2004 MITSUBISHI ENDEAVOR lock

14. If not DTC is shown, terminate scan tool MB991958.
15. Turn the ignition switch to "LOCK" (OFF) position.
16. Disconnect scan tool MB991958. REGISTRATION OF ADDITIONAL KEYS WITH THE SCAN TOOL Additional key(s) can be registered with the scan tool while keeping all existing key
data.
1. Connect scan tool MB991958 to the 1
6-pin data link connector.
CAUTION: To prevent damage to scan tool MB991958, always
turn the ignition switch to "LOCK" (OFF) position
before connecting or disconnecting scan tool
MB991958.
NOTE: To register additional keys with the scan tool, no registered
keys must be lost.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 110: Displaying "Transponder ID Addition" (3 Of 3)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
8. This completes the registration operation. Turn the ignition switch
"LOCK" (OFF) and leave it off for approximately ten seconds.
9. Check that the engine can be started with each of the ignition keys.
10. Check that the immobilizer system DTC and MFI system DTC did not set.
11. If not DTC is shown, terminate scan tool MB991958.
12. Turn the ignition switch to "LOCK" (OFF) position.
13. Disconnect scan tool MB991958.
REGISTRATION OF ADDITIONAL KEY(S) WITHOUT USING THE SCAN TOOL
NOTE: A maximum of eight different keys can be registered.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
8. If a new ignition key is registered further, repeat steps 1 to 7 above.
A maximum of eight ignition keys can be registered to one vehicle (If you
attempt to register the ninth key, the immobilizer-ECU rejects the key). If any
of the following conditions are satisfied, the additional key registration mode
will terminate:
The immobilizer indicator starts blinking for more than 30 seconds. After the ignition key has been turned to the "LOCK" (OFF), the engine
control relay is turned off. The scan tool has started communicating with vehicle systems.
9. After the registration mode has terminated, the additionally registered key(s)
should allow you to start the engine.
TRANSPONDER LOCK CHECK Required Special Tools:
MB991958: Scan Tool (MUT-III Sub Assembly)
MB991824: Vehicle Communication Interface (V.C.I.) MB991827: MUT-III USB Cable MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system)
Follow the procedure below to judge if the ignition key can be overwritten (i.e. the
ignition key is correct) or not.
1. Connect the scan tool MB991958 to the data link connector. CAUTION: To prevent damage to scan tool MB991958, always
turn the ignition switch to "LOCK" (OFF) position
before connecting or disconnecting scan tool
MB991958.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 118: Identifying TP Lock Check Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
IGNITION SWITCH REMOVAL AND INSTALLATION < UP TO DECEMBER 2003 > Fig. 119: Removing/Installing Ignition Switch

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS
< < A > > STEERING COLUMN UPPER COVER/STEERING COLUMN LOWER COVER REMOVAL 1. Rotate the steering wheel with a slightly from side-to-side to access and
remove the mountin
g screws.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 120: Removing Steering Column Upper/Lower Cover

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
< < B > > STEERING LOCK CYLINDER REMOVAL 1. Insert the key in the steering lock cylinder and turn it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the steering lock cylinder toward
you.
Fig. 121: Removing Steering Lock Cylinder

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL AND INSTALLATION < FROM TO JANUARY 2004 >
WARNING:
Before removing the steering wheel, air bag
module assembly and clock spring refer to AIR BAG RESTRAINT SYSTEMS
).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 123: Removing Steering Column Upper/Lower Cover

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
< < B > > STEERING LOCK CYLINDER REMOVAL 1. Insert the key in the steering lock cylinder and turn it to the "ACC" position.
2. Using a small Phillips head screwdriver pull the steering lock cylinder toward
you
Fig. 124: Removing Lock Cylinder

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION < UP TO DECEMBER 2003 > IGNITION SWITCH CONTINUITY CHECK Disconnect ignition switch connector C-308 without removing the ignition switch
and steering lock cylinder. Then check the continuity.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 126: Checking Ignition Switch Continuity

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
KEY REMINDER SWITCH CHECK Disconnect key reminder switch connector C-310 without removing the key
reminder switch and steerin
g lock c
ylinder.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 128: Checking Key Reminder Switch Continuit
y
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION < FROM TO JANUARY 2004 > IGNITION SWITCH CONTINUITY CHECK Disconnect ignition switch connector C-308 without removing the ignition switch
and steering lock cylinder. Then check the continuity.
Fig. 129: Disconnecting Ignition Switch Connector C
-308

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor