2004 MITSUBISHI ENDEAVOR window

Fig. 14: Checking Power Window Fuse Voltage

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
POWER WINDOW RELAY CHECK POWER WINDOW RELAY CHECK SPECIFICATION BATTERY VOLTAGE
TESTER CONNECTION
SPECIFIED
CONDITION
Not applied
4-5
Open circuit
Connect terminal
No. 3 and the
negative battery
terminal. Connect terminal
No. 1 and the
positive battery
4-5
Less than 2 ohms

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 15: Identif
ying Power Window Rela
y

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
CIRCUIT BREAKER (INCORPORATED IN THE POWER WINDOW MOTOR) INSPECTION 1. Pull the power window switch to the UP position to fully close the door
window glass, and keep pulling the switch for an additional ten seconds.
2. Release the power window switch from the UP position and immediately press
it to the DOWN position. The condition of the circuit breaker is good if the
door window glass starts to move downwards within about 60 seconds. POWER WINDOW CHECK 1. Operate the power window switch of each door to verify that the power
windows operate properly. If they don't, then troubleshoot as described in
SYMPTOM CHART
.
2. Turn ON the power window lock switch of the power window main switch.
Then operate the passenger's door and rear door power window sub-switches to
ensure that they do not operate. If they do, replace the power window main
switch (Refer to DOOR GLASS AND REGULATOR
).
CENTRAL DOOR LOCKING SYSTEM INSPECTION Check the following. Troubleshoot if operations malfunction (Refer to SYMPTOM CHART
).
Insert the key into the driver's key cylinder and turn once to the unlock side to
unlock the driver's door. Turn the key once again to the unlock side to unlock
all doors and the liftgate. All doors and liftgate can be locked using the door lock switch built into the
front power window (main or sub < RH>) switch.
DOOR OUTSIDE HANDLE PLAY CHECK 1. Check that the door outside handle play is within the standard value range.
Standard value (B):
Front door: 10 +/- 3.5 mm (0.39 +/- 0.138 inch)
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Required Special Tools:
MB990480: Window Glass Holder MB990784: Ornament Remover MB991223: Harness Set
REMOVAL SERVICE POINTS << A >> WINDOW REGULATOR ASSEMBLY REMOVAL 1. Remove the door window glass installation bolts.
2. Lift the door window glass, and attach special tool MB990480 to the glass as
shown to prevent the glass from falling.
3. Remove the window re
gulator assembl
y and
power win
dow motor assembl
y.
CAUTION: If tinting film is adhered to the door window
glass, attach special tool MB990480 to the
outside of the glass to prevent the film from
peeling off.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 24: Removing Window Regulator Assembly

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
<< B >> POWER WINDOW SWITCH PANEL ASSEMBLY REMOVAL Insert special tool MB990784 as shown to remove the power window switch panel
assembl
y.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 25: Removing Power Window Switch Panel Assembly

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION POWER WINDOW SWITCH CONTINUITY CHECK Remove the power window switch (Refer to DOOR GLASS AND REGULATOR
).
POWER WINDOW MAIN SWITCH'S FRONT < LH> SWITCH CHECK Connect the terminal number 13 to the battery (+) post, and the terminal number 12
to the battery (-) post. MAIN SWITCH MAIN SWITCH SPECIFICATION
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
FRONT (LH)
UP
8-13, 9-12,
Less than 2 ohms
OFF
8-12, 9-12
Less than 2 ohms
DOWN
9-13, 8-12
Less than 2 ohms
FRONT (RH)
UP
3-13, 11-12*
Less than 2 ohms
OFF
3-11, 3-12*, 11-12*
Less than 2 ohms
DOWN
11-13, 3-12*
Less than 2 ohms
REAR (LH)
UP
1-13, 2-12*
Less than 2 ohms
OFF
1-2, 1-12*, 2-12*
Less than 2 ohms
DOWN
2-13, 1-12*
Less than 2 ohms
REAR (RH)
UP
13-14, 6-12*
Less than 2 ohms
OFF
6-14, 6-12*, 12*--14
Less than 2 ohms
DOWN
6-13, 12*--14
Less than 2 ohms
NOTE: *: Set the window lock switch to UNLOCK position.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 28: Identifying Sub Rear Switch Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DOOR WINDOW REGULATOR CHECK 1. Connect a battery directly to the motor terminals and check that the motor runs
smoothly.
2. Check that the motor runs in the opposite direction when the battery is
connected with the polarity reversed.
3. If defect is found, re
place the window re
gulator as an assembl
y.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor