Page 979 of 3870
Fig. 108: Reducing Speed
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Check to be sure that deceleration continues while the switch is pressed, and
that after it is released the constant speed at the time when it was released
becomes the driving speed.
RETURN TO THE SET SPEED BEFORE CANCELLATION AND AUTO-CRUISE CONTROL
CANCELLATION
NOTE: When the vehicle speed reaches the low limit
[approximately 40 km/h (25 mph)] during deceleration,
the auto-cruise control will be cancelled.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 980 of 3870
1. Set the auto-cruise speed control.
2. When any of the following operations are performed while at constant speed
during auto-cruise control, check if normal driving is resumed and deceleration
occurs.
1. The auto-cruise control switch is pulled in the direction of arrow.
2. The brake pedal is depressed.
3. The selector lever is moved to the "N" range.
3. At a vehicle speed of 40 km/h (25 mph) or higher, check if when the
"ACC/RES" switch is switched ON, the vehicle speed returns to the speed
before auto-cruise control driving was cancelled, and constant speed driving
occurs.
Fig. 109: Resuming Set Speed
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. When the "CRUISE" (MAIN) switch is turned to the "OFF" while driving at
constant speed, check if normal driving is resumed and deceleration occurs.
AUTO-CRUISE CONTROL SYSTEM COMPONENT CHECK STOPLIGHT SWITCH
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 981 of 3870
1. Disconnect the connector.
2. Check for continuity between the terminals of the switch.
Fig. 110: Checking Connector
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 982 of 3870
Fig. 111: Identifying Condition Table
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
TRANSMISSION RANGE SWITCH ("N" POSITIN) Refer to ESSENTIAL SERVICE
.
THROTTLE POSITION SENSOR Refer to THROTTLE ACTUATOR CONTROL MOTOR CHECK
.
AUTO-CRUISE CONTROL SWITCH CHECK 1. Remove the auto-cruise control switch. (Refer to AUTO
-CRUISE
CONTROL
).
2. Measure the resistance between terminal 2 and terminal 3 when each of the
"COAST/SET", "ACC/RES", "CANCEL" and "CRUISE" (MAIN) switches is
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 983 of 3870
pressed. If the values measured at the time correspond to those in the table below, the resistance values are correct.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 984 of 3870
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 985 of 3870
Fig. 112: Checking Auto Cruise Control Switc
h
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 113: Identifying Switch Position And Specified Condition Table
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
AUTO-CRUISE CONTROL REMOVAL AND INSTALLATION
WARNING:Before removal of the air bag module, refer to AIR
BAG SAFETY PRECAUTIONS
and DRIVER
-SIDE AIR
BAG MODULE & CLOCKSPRING
.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 986 of 3870
Fig. 114: Identifying Auto Cruise Control Components
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
