2004 ISUZU TF SERIES lock

FRONT WHEEL DRIVE 4C1-63

13. Wheel Pin
(1) Place hub on a wood workbench or a block of wood,
approx. 6” by 6” to protect the wheel stud ends and threads.
(2) Install wheel stud using a hammer.
Be sure wheel stud is started squarely and seats
completely.

(3) Align index marks and install hub to disc.


14. Bolt
Torque N
m (kgf
m/lb
ft)
103 
10 (10.5 
1/75.9 
7.2)



15. ABS sensor rotor
(1) Set a new ABS sensor rotor, if replacement is required.
(2) Install the ABS sensor rotor in the hub, using special tools.
Installer : 5-8840-2789-0
Grip : 5-8840-0007-0
Refer to the section Brake.


16. Inner Bearing
Outer race ; outer bearing
Install the outer race by driving it into the hub.
Installer : 5-8840-2119-0
(J-36829)
Grip : 5-8840-0007-0
(J-8092)

FRONT WHEEL DRIVE 4C1-65


Preload Adjustment
Tighten the hub nut at 29.4 Nm (3 kgfm / 21.716 lb.ft), then
loosen the nut to the full.
Tighten the hub nut at the value given below, using a spring
scale on the wheel pin.
Bearing Preload N(lb)

New bearing and New oil seal 20 - 25 (4.4 - 5.5)
Used bearing and New oil seal 12 - 18 (2.68 - 4.0)
If the measured bearing preload is outside the specifications,
adjust it by loosening or tightening the bearing nut.



21. Lock Washer
Turn the side with larger diameter of the tapered bore to the
vehicle outer side, and attach the washer.
If the bolt holes in the lock plate are not aligned with the
corresponding holes in the nut, reverse the lock plate.
If the bolt holes are still out of alignment, turn in the nut just
enough to obtain alignment,. Screw is to be fastened tightly so
its head may come lower than the surface of the washer.


22. Body Assembly
Apply adhesive (Loctite 15 or equivalent) to the both joining
faces.


23. Snap Ring and Shims
Adjust the clearance between the free wheeling hub body and
the snap ring.
Clearance mm(in)
0 - 0.2 (0 - 0.08)
Adjust Shims Available mm(in)
0.2, 0.3, 0.5, 1.0
(0.008, 0.011, 0.020, 0.039)


24. Cover Assembly
Align stopper nails to grooves of body.

FRONT WHEEL DRIVE 4C1-77
ITEM NO. ILLUSTRATION PART NO. PART NAME


FAL-58

5-8522-0054-0
(J-29015)
Inner bearing installer
(for 2WD)


FAL-54

5-8522-0051-0
(J-33161)
Hub oil seal installer
(for 2WD)


FAL-62

5-8840-2117-0
(J-36827)

Hub nut wrench


FAL-17

5-8840-2119-0
(J-36829)
Outer bearing inner race
installer (for 4WD)


FAL-19

5-8840-2120-0
(J-36830)

Oil seal installer (for 4WD)


FAL-18

5-8522-0054-0
(J-29015)
Outer bearing outer race
installer (for 4WD)


FAL-61

5-8840-2137-0
(J-38194)

Inner cam installer


FAL-39


5-8840-2126-0
Auto locking shim gauge
(for 4WD)


FAL-60


5-8840-2125-0
Snap ring installer
(for 4WD)

SHIFT ON THE FLY SYSTEM 4C2-1

DRIVELINE/AXLE
SHIFT ON THE FLY SYSTEM
CONTENTS

Service Precaution............................................. 4C2-1
Shift On The Fly System .................................... 4C2-2
Outline of Shift on The Fly System ................. 4C2-2
Shift On The Fly Electrical Equipment ............... 4C2-3
Axle Shaft Connection and Disconnection ..... 4C2-3
Actuator Assembly.......................................... 4C2-3

Shift On The Fly System and Association
Parts ................................................................. 4C2-4
Disassembly ................................................... 4C2-5
Inspection and Repair..................................... 4C2-6
Reassembly .................................................... 4C2-9
Torque Specifications ..................................... 4C2-12
Special Service Tool ....................................... 4C2-13



Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.


CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners o
r
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

BRAKE CONTROL SYSTEM 5A-1


SECTION 5A
BRAKE CONTROL SYSTEM
CONTENTS

Service Precaution ............................................................................................................. 5A-4
General Description ........................................................................................................... 5A-5
EHCU, Brake Pipe Diagram .......................................................................................... 5A-6
Hydraulic Unit (H/U)....................................................................................................... 5A-7
Normal Braking ......................................................................................................... 5A-8
Pressure Isolation (Pressure Maintain) .................................................................. 5A-9
Pressure Reduction .................................................................................................. 5A-10
Brake Release ........................................................................................................... 5A-11
Circuit Diagram.............................................................................................................. 5A-12
Connector List ............................................................................................................... 5A-13
Part Location ................................................................................................................. 5A-15
EHCU Pin-outs ............................................................................................................... 5A-17
System Components ..................................................................................................... 5A-19
Electronic Hydraulic Control Unit (EHCU) .............................................................. 5A-19
ABS Warning Lamp .................................................................................................. 5A-19
Wheel Speed Sensor (WSS)..................................................................................... 5A-19
G-Sensor ................................................................................................................... 5A-19
Normal and Anti-lock Braking ................................................................................. 5A-19
Electronic Brake-force Distribution (EBD) System ................................................ 5A-20
Brake Pedal Travel.................................................................................................... 5A-20
Acronyms and Abbreviations ....................................................................................... 5A-20
General Diagnosis ............................................................................................................. 5A-20
General Information ...................................................................................................... 5A-20
ABS Service Precautions.............................................................................................. 5A-20
Computer System Service Precautions....................................................................... 5A-21
General Service Precautions........................................................................................ 5A-21
Note on Intermittents .................................................................................................... 5A-21
Test Driving ABS Complaint Vehicles ......................................................................... 5A-21
"ABS and Brake" Warning Lamp ................................................................................. 5A-22
Normal Operation .......................................................................................................... 5A-22

5A-2 BRAKE CONTROL SYSTEM

Brake (EBD) Warning Lamp.......................................................................................... 5A-22
Tech 2 Scan Tool ........................................................................................................... 5A-23
DATA LIST (Tech 2) ....................................................................................................... 5A-26
Actuator Test (Tech 2)................................................................................................... 5A-27
Diagnostic Trouble Codes................................................................................................. 5A-30
Diagnosis By "ABS" Warning Lamp Illumination Pattern .............................................. 5A-32
Basic Diagnostic Flow Chart ............................................................................................ 5A-35
Basic Inspection Procedure .............................................................................................. 5A-37
1. Basic Inspection of Service Brake ........................................................................... 5A-37
2. Ground Inspection .................................................................................................... 5A-37
Wheel Speed Sensor Inspection Procedure .................................................................... 5A-38
Symptom Diagnosis........................................................................................................... 5A-39
ABS Works Frequently But Vehicle Does Not Decelerate ......................................... 5A-39
Uneven Braking Occurs While ABS Works ................................................................. 5A-40
The Wheels Are Locked ................................................................................................ 5A-40
Brake Pedal Feed Is Abnormal ..................................................................................... 5A-41
Braking Sound (From EHCU) Is Heard
While Not Braking ....................................................................................................... 5A-42
No ABS Warning Lamp ................................................................................................. 5A-43
DTC C0221 (Flash Code 21) Front Right Wheel Speed Sensor
Short Circuit or Circuit Open ......................................................................................... 5A-44
DTC C0222 (Flash Code 22) Front Right Wheel Speed Sensor Incorrect Signal.......... 5A-46
DTC C0223 (Flash Code 23) Front Right Wheel Speed Sensor
Signal - Tooth Chipping................................................................................................... 5A-48
DTC C0225 (Flash Code 25) Front Left Wheel Speed Sensor Short Circuit or
Circuit Open .................................................................................................................... 5A-50
DTC C0226 (Flash Code 26) Front Left Wheel Speed Sensor Incorrect Signal ............ 5A-52
DTC C0227 (Flash Code 27) Front Left Wheel Speed Sensor Signal - Tooth
Chipping ........................................................................................................................... 5A-54
DTC C0231 (Flash Code 31) Rear Right Wheel Speed Sensor Short Circuit or
Circuit Open .................................................................................................................... 5A-56
DTC C0232 (Flash Code 32) Rear Right Wheel Speed Sensor Incorrect Signal ........... 5A-58
DTC C0233 (Flash Code 33) Rear Right Wheel Speed Sensor Signal - Tooth
Chipping ........................................................................................................................... 5A-60

5A-4 BRAKE CONTROL SYSTEM

DTC C0277 (Flash Code 77) Power Supply Low Input .................................................... 5A-84
DTC C0278 (Flash Code 78) Power Supply High Input ................................................... 5A-84
DTC C0282 (Flash Code 82) 4 Wheel Drive State Input Signal Failure .......................... 5A-86
DTC C0285 (Flash Code 85) Assembly Error (G-sensor) ................................................ 5A-88
Special Tools ...................................................................................................................... 5A-90


Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.



CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

BRAKE CONTROL SYSTEM 5A-5

General Description
EHCU has controlled ABS (Anti-lock Brake System)
and EBD (Electronic Brake-force Distribution System).
ABS works on all four wheels. EBD system works on
rear 2 wheels. A combination of wheel speed sensor
and Electronic Hydraulic Control Unit (EHCU) can
determine when a wheel is about to stop turning and
adjust brake pressure to maintain best braking. This system helps the driver maintain greater control of
the vehicle under heavy braking conditions.

Note: The Electronic Hydraulic Control Unit (EHCU)
comprises the Hydraulic Unit (H/U) and Control Unit.













This illustration is based on RHD model
C05L300010
Legend

(1) Electronic (6) Front Left Wheel Speed Sensor
(2) Hydraulic (7) Rear Right Wheel Speed Sensor
(3) Hydraulic Unit (H/U) (8) Rear Left Wheel Speed Sensor
(4) Control Unit (9) G-sensor (4WD only)
(5) Front Right Wheel Speed Sensor (10) 2-4WD Control Unit (4WD only)