2004 ISUZU TF SERIES wheel bolt torque

4C1-66 FRONT WHEEL DRIVE

25. Bolt
Torque Nm (kgfm/lbft)
12.0 
2.0 (1.2 
0.2 / 8.7 
1.4)

ANTI-LOCK BRAKE SYSTEM 5B-7

Electronic Hydraulic Control Unit
Electronic Hydraulic Control Unit and Associated Parts



RHD model LHD model
350R300001-X

Legend


1.
Flare Nut from master cylinder front

2.
Flare Nut to front right wheel cylinder

3. Flare Nut to front left wheel cylinder

4.
Flare Nut to rear wheel cylinder


5.
Electronic Hydraulic Control Unit (EHCU)

6.
Flare Nut from master cylinder rear

7.
Bolt

8.
Front

Removal
1. Disconnect the harness connector.
2. Loosen five flare nuts and remove brake pipes.


After disconnecting brake pipe, cap or tape the
openings of the brake pipe to prevent the entry o
f
foreign matter.
3. Remove three bracket fixing bolts.

Installation
1. Install EHCU and tighten the bolt to the specified
torque.

Torque : 8 N
m (0.8 kg
m /69 lb in)
2. Tighten the flare nuts to the specified torque.

Torque : 16 N
m (1.6 kg
m /12 lb ft)

3. Connect the harness connector.

ANTI-LOCK BRAKE SYSTEM 5B-13

Front Speed Sensor Rotor
Front Sensor Rotor and Associated Parts
411R300010
Legend


1.
Sensor Rotor

2.
Hub and Disc


3.
Disc Rotor fixing Bolt

4. Hub and Disc Assembly

Removal
1. Remove the hub and disc assembly (4). (Refer to
the section Front wheel Drive).
2. Remove two disc rotor fixing bolts (3) on a diagonal.
3. Drive out the sensor rotor using a metal bar and
hammer through the two bolt holes.


Discard the used sensor rotor.
4. Install disc rotot fixing bolts and tighten them to the
specified torque.

Torque : 103 N
m (10.5 kg
m /76 lb ft)

5C-48 BRAKES



Important Operations
Note :


Wash the disassembled parts in clean brake fluid.


Use compressed air to clean the ports.


Protect the disassembled part surfaces from dust and othe
r
foreign material contamination.


Before reassembly, check the part surfaces for dust and
other foreign material contamination.


Be sure to replace the designated parts with new ones.

4. Piston Assembly
Install new piston cups on each piston so that the flared end of
the cups are turned to the inboard side of the pistons.
Attach the return spring and the boot to the piston.
Be sure to use new piston cup and boot.




Apply brake fluid to the piston and the inner face of the
boots.


Note the direction of piston cup.



5. Bleeder ; Wheel Cylinder
Torque Nm(kgfm/Ibin)
6 - 8 (0.6 – 0.8 / 52 - 69)



9. Wheel Cylinder Assembly
10. Bolt ; Wheel cylinder
Torque N
m(kgf
m/Ib
ft)
7 - 11 (0.7 – 1.1 / 61 - 95)

5D-10 PARKING BRAKE SYSTEM

Removal
1. Remove wheel and tire.
2. Remove brake drum.
3. Remove tension pin (1) and shoe clamp spring (2).
4. Remove return spring (3).
5. Remove shoe assemblly with parking brake leve
r
(4).
6. Remove shoe assembly with adjuster lever (5) and
spring (6).
7. Remove parking brake inner cable from parking
brake lever (4).
8. Use offset box wrench (12mm hex.) to compress
locking lugs on the cable, then remove parking
brake outer cable from back plate.
NOTE: Do not twist or bend the cable too much.
A damaged cable will cause poor operation or a cable
break down.





311RS012

Legend
(1) Offset Box Wrench (12mm hex)
9. Remove nut (8) to fix the cable (7) on the leaf
spring.
10. Take out parking brake rear cable (7) from the
back plate.
11. Remove bolt (9) and nut (10).
12. Disconnect T-end (11) from the equalizer of front
cable.

Installation
NOTE: Be sure to use the new shoe clamp spring (2)
and the new adjuster lever clip (14).
1. Apply grease (multipurpose type grease) to the
connecting portion of the rear cable (11) and
equalizer (13). (aroow mark).
2. Install parking brake outer cable in back plate and
inner cable in parking brake lever (4).
3. Install return spring (3).
4. Install shoe clamp spring (2) and tension pin (1)
5. Install shoe assembly with adjuster lever, shoe
assembly with parking brake lever (4) and spring
(6). ---- snap action
6. Install nut (8) and tighten it to the specified torque.
Torque: 7N




m (0.7 kg




m/61 lb in)
7. Connect T-end (11) with equalizer (13) through
outer cable retainer (12).
8. Install nut (10) and tighten it to the specifed
torque.
Torque: 15 N





m (1.5 kg





m/11 lb ft)
9. Install bolt (9) and tighten it to the specified
torque.
Torque: 7 N




m (0.7 kg




m/61 lb in)
10. Install brake drum.
11. Install wheel and tire.
12. Pull parking brake lever with a force equivalent to
poerating force: 490 N (50 kg/110 lb), 10 times fo
r
conditioning.
13. Adjust parking brake lever adjusting nut so that
parking brake lever goes through 8

14 (bench
seat) or 6

8 (bucket seat) notches, when pulled
with a operation force of 294N (30 kg/66 lb).
14. Check brake for no drag.

CAB 10-33
Important Operations
15. Instrument Panel & Crass Beam Assembly
1) Tighten the 4 bolts fixing the cross beam and body panel
to the specified torque.
Torque N
m (kgf
m/lb
ft)
19 (1.9/14)

2) A Bolt: Steering Column to Cross Beam
Torque N
m (kgf
m/lb
ft)
20 (2.0/14)
B Bolt: Pedal Bracket to Cross Beam
Torque N
m (kgf
m/lb
ft)
15 (1.5/11)


3) C Bolt: Parking Brake Bracket to Cross Beam
Torque Nm (kgfm/lbft)
15 (1.5/11)

21. Steering Wheel/Steering Cowl

Tighten the steering wheel fixing nut to the specified
truque.
Torque N
m (kgf
m/lb
ft)
35 (3.6/26)

CLUTCH 7C-23
015RW053
6. Flywheel Assembly and Crank Bearing (6VE1)
(1) Remove flywheel assembly and crankshaft bearing. Do no
t
remove except for replacement.
(2) Use the remover 5-8840-2000-0 (J-5822) and sliding
hammer 5-8840-0019-0 (J-23907) to remove the crankshaf
t
bearing



Important Operations - Installation
Follow the removal procedure in reverse order to perform the
installation procedure.
Pay careful attention to the important points during the
installation procedure.

015RW054
6. Flywheel Assembly and Crank Bearing (6VE1)
(1) Install flywheel assembly and crankshaft bearing. Use the
installer 5-8840-0125-0 (J-26516-A) and driver handle 5-
8840-0007-0 (J-8092) to install the crankshaft bearing then
clean and lubricate with grease.
015RS047
(2) Install new flywheel fixing bolts in the order illustrated and
tighten them to the specified torque.
N
m (kg
m/lb ft)

6VE1 54 (5.5/40)
NOTE: Do not reuse the bolt and do not apply oil or thread lock
to the bolt.

CLUTCH 7C-25


(4) Clean the pressure plate surfaces.
(5) Align the pressure plate assembly

4 with the flywheel
knock pin

5.
(6) Install the pressure plate assembly to the flywheel.
(7) Tighten the clutch cover bolts a little at a time in the
numerical order shown in the illustration.
Clutch Cover Bolt Torque N
m (kgf
m/lb
ft)
18 
3 (1.8 
0.3 / 13.0 
2.2)

201RS017




(8) Remove the clutch pilot aligner.
Note:
Do not strike the clutch pilot aligner with a hammer to
remove it.


4JH1-TC, C24SE
6VE1