2004 ISUZU TF SERIES engine

SHEET METAL 2B-3



Important Operations - Removal
1. Washer Nozzle Tube

1) Open the hood.
2) Support the hood.
3) Remove the windshield washer nozzle tube.




2. Hood Hinge Bolts



Before removing
the hinges from the engine hood, scribe a
mark showing location of
the hinges to facilitate installation in
the original position.

RTW32BSH000101

Important Operations - Installation
3. Engine Hood


Check the engine hood and fender. (1)




Clearance : 4.0 mm (0.16 in)


Height (step) : Flushness


Adjust clearance with the hinges on the engine hood.











Adjust height (step) with the hood rests (1).






Engine Hood Striker


Apply a light coat of grease to the striker.

2B-4 SHEET METAL


2. Hood Hinge Bolts


Tighten the engine hood hinge fixing bolts to the specified
torque.

Torque N
m(kgf
m/lb
in)
10 (1.0
/ 87)

SHEET METAL 2B-5
ENGINE HOOD LOCK
REMOVAL AND INSTALLATION



This illustration is based on the RHD model.
RTW42BMF000101

Removal Steps
Installation Steps


1. Radiator grille


4. Control cable


2. Engine food lock assembly
3. Hood lock control lever
3. Hood lock control lever


2. Engine food lock assembly


4. Control cable
1. Radiator grille



Important Operations - Removal
1. Radiator Grille
Refer to the Radiator Grille in this section.


2. Engine Hood Lock Assembly

Apply setting marks (1) to the hood lock assembly and the
body prior to removal.

4. Control Cable
Pull out the control cable toward the passenger compartment.

2B-6 SHEET METAL


Important Operations - Installation
4. Control Cable

Reroute the control cable to its original position, and check and
see if the lock assembly and control lever work normally.


2. Engine Hood Lock Assembly

Adjustment
1) Install the engine hood lock assembly (4) and temporaril
y
tighten the bolts securing it.
2) Close the hood.
3) Position the hood so that the stepped portion between the
hood (1) and the fender (2) is precisely 1.5 mm (0.06 in)
high.
4) Final tighten the bolts securing the engine hood lock
assembly.



5) Turn the buffers (3) counterclockwise until the stepped
portion between the hood and the fender disappears.
6) Tighten the hood lock assembly fixing bolts to the specified
torque.

Torque N
m(kgf
m/lb
in)
10 (1.0
/ 87)

GENERAL INFORMATION 0A-5

7. Measurement criteria are defined by the terms "standard" and "limit".

A measurement falling within the "standard" range indicates that the applicable part or parts are serviceable.
"Limit" is an absolute value.

A measurement falling outside the "limit" indicates that the applicable part or parts must be repaired or replaced.
8. Components are parts are listed in the singular form throughout the Workshop Manual.
9. The following directional criteria are used throughout the Workshop Manual:

Front:

The cooling fan side of the engine.
Right:

The right-hand side of the engine viewed from the flywheel.

Left:
The left-hand side of the engine viewed from the flywheel.

Rear:

The flywheel side of the engine.
Cylinder numbers are counted from the front of the engine towards the rear.

The engine's rotation is clockwise viewed from the front of the engine.

0A-6 GENERAL INFORMATION
IDENTIFICATION



CHASSIS NUMBER
The chassis number is stamped on the right-hand side of the
chassis side member under the right door.




VEHICLE IDENTIFICATION PLATE
The vehicle identification plate is attached to the upper face of
the radiator sill in the engine compartment.




BODY AND OPTION IDENTIFICATION
PLATE
The body and option plate shows body style, body serial
number, paint and trim colour combination, paint number,
engine transmissions, axle ratio options and built date. The
built date is defined as 'the date of manufacture' by the
calendar month and year in which the body shell and power
train sub-assemblies are co-joined or moved from the
production line.

0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE (For GENERAL EXPORT)
Items followed by an asterisk (*) require more frequent maintenance if the vehicle is driven under severe conditions.
Refer to "SEVERE CONDITIONS MAINTENANCE SCHEDULE."

I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate


SERVICE INTERVAL:

1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60or months whichever
comes fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
ENGINE Idling speed and acceleration
(GASOLINE) I I - I - I - I - I - I - I - I - I - I
(DIESEL) I I I I I I I I I I I I I I I I I I I I * Air cleaner element
(GASOLINE) - I - I - I - R - I - I - I - R - I - I
(DIESEL) I I I I I I I R I I I I I I I R I I I I * P Engine oil (6VE1) - R - R - R - R - R - R - R - R - R - R * P Engine oil (C24SE) Replace every 12,000km * D Engine oil (4JH1-TC) - R - R - R - R - R - R - R - R - R - R * D Engine oil (4JA1-TC) - - R - - R - - R - - R - - R - - R - - * D Engine oil (4JA1-T) RR R R RR RRRRRRRR R R R RRR * P Engine oil filter (6VE1) - R - R - R - R - R - R - R - R - R - R * P Engine oil filter (C24SE) Replace every 12,000km * D Engine oil filter (4JH1-TC, 4JA1-T) - R - R - R - R - R - R - R - R - R - R * D Engine oil filter (4JA1-TC) - - R - - R - - R - - R - - R - - R - - Oil leakage and contamination
(GASOLINE) - I - I - I - I - I - I - I - I - I - I
(DIESEL) I I I I I I I I I I I I I I I I I I I I Fuel leakage I I - I - I - I - I - I - I - I - I - I Fuel tank - - - | - - - | - - - | - - - | - - - | P O2 Sensor Replace every 160,000km P Valve clearances (6VE1) Check and adjust if noisy D Valve clearances A - - A - - - A - - - A - - - A - - - A P Spark plugs (C24SE) (for leaded
fuel use) - R - R - R - R - R - R - R - R - R - R
P Spark plugs (C24SE) (for unleaded
fuel use) - - - - - R - - - - - R - - - - - R - -
P Spark plugs (6VE1) Replace every 160,000km Spark plug wire | | - | - | - | - | - | - | - | - | - | Fuel filter (GASOLINE) - - - R - - - R - - - R - - - R - - - R Fuel filter (DIESEL) - - R - - R - - R - - R - - R - - R - - Engi ne / Accessory dri ve belt
(GASOLINE) - - - - - - - - - R - - - - - - - - - R
Fan belt tension and damage
(DIESEL) I I I I I I I I I I I I I I I I I I I I
* Exhaust system I I - I - I - I - I - I - I - I - I - I Engine coolant concentration (6VE1) - - - - - - - - - R - - - - - - - - - R (C24SE) - | - | - | - | - R - | - | - | - | - R Engine coolant level concentration
(DESEL) I I I I I I I I I R I I I I I I I I I R
Cooli ng sy stem for water l eakage - I - I - I - I - I - I - I - I - I - I All hoses and pipes in engine
compartment for clogs or damage - I - I - I - I - I - I - I - I - I - I
P Timing belt (C24SE) - - - - - - - - - - - - - - - I - - - - (Replace every 120,000km) P Timing belt (6VE1) Replace every 160,000km CLUTCH Cl utch fl ui d I I - I - I - I - I - I - I - I - I - I Clutch pedal travel and free play I I - I - I - I - I - I - I - I - I - I

MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SCHEDULE (For EUROPE)
Items followed by an asterisk (*) require more frequent maintenance if the vehicle is driven under severe conditions.
Refer to "SEVERE CONDITIONS MAINTENANCE SCHEDULE."
Diesel Engine model (ACEA B2 specification engine oil)

I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate


SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
DIESEL ENGINE * Engine oil (4JH1-TC) - R - R - R- R- R- R- R - R - R- R* Engine oil (4JA1-TC) - - R - - R - - R - - R - - R - - R - - * Engine oil filter(4JH1-TC) - R - R - R- R- R- R- R - R - R- R* Engine oil filter (4JA1-TC) - - R - - R - - R - - R - - R - - R - - Oil leakage and contamination I I I I I I I I I I I I I I I I I I I I Idling speed and acceleration I I I I I I I I I I I I I I I I I I I I Fan belt tension and damage I I I I I I I I I I I I I I I I I I I I Exhaust system I I - I - I - I - I - I - I - I - I - I All hoses and pipes in engine
compartment for clog of damage - I I I I I I I I I I I I I I I I I I I
Valve clearance (4JH1-TC) - - - A - - - A - - - A - - - A - - - A Valve clearance (4JA1-TC) - - A - - A - - A - - A - - A - - A - - * Air cleaner element (4JH1-TC) I I I I I I I R I I I I I I I R I I I I * Air clearance element (4JA1-TC) - - I I I I I I R I I I I I I I I R I I Fuel filter (4JH1-TC) - - R - - R - - R - - R - - R - - R - - Fuel filter (4JA1-TC) - - - - - - - - R - - - - - - - - R - - Engine coolant concentration (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Engine coolant concentration
(4JA1-TC) - - I - - I - - I - - I - - I - - I - - Cooling system for water leakage
(4JH1-TC) - I - I - I - I - I - I - I - I - I - I Cooing system for water leakage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - CLUTCH Clutch fluid (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Clutch fluid (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Clutch pedal travel and play (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Clutch pedal travel and play (4JA1-TC) - - I - - I - - I - - I - - I - - I - - TRANSMISSION OR TRANSMISSION
WITH TRANSFER CASE
* Manual transmission with fluid (4JH1-TC) - R - I - - - R - - - I - - - R - - - I * Manual transmission with fluid
(4JA1-TC) - - R - - I - - R - - I - - R - - I - - * Transfer case oil (4JH1-TC) - - - I - - - I - - - I - - - I - - - I * Transfer case oil (4JA1-TC) - - R - - I - - R - - I - - R - - I - - Oil leakage (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Oil leakage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Gear control mechanism for
looseness (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Gear control mechanism for
looseness (4JA1-TC) - - - - - - - - I - - - - - - - - I - I * AT Automatic transmission fluid
(4JH1-TC) - - - I - - - I - - - I - - - I - - - I * AT Automatic transmission fluid (4JA1-TC) - - - - - - - - I - - - - - - - - I - I * AT Transfer case oil (4JH1-TC) - R - I - - - R - - - I - - - R - - - I * AT Transfer case oil (4JA1-TC) - - R - - I - - R - - I - - R - - I - -