2004 INFINITI QX56 Back up

ATC-72
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
3. CHECK PBR REFERENCE SIGNAL VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect air mix door motor (Passenger) connector M143.
3. Turn ignition switch ON.
4. Check voltage between air mix door motor (Passenger) harness
connector M143 terminal 3 (Y) and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK PBR REFERENCE VOLTAGE CIRCUIT BETWEEN AIR MIX DOOR (PASSENGER) AND
FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between air mix door motor (Passenger) har-
ness connector M143 terminal 3 (Y) and front air control harness
connector M49 terminal 2 (Y).
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> Repair or replace harness as necessary.
5. CHECK PBR GROUND REFERENCE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between air mix door motor (Passenger) har-
ness connector M143 terminal 2 (P) and front air control harness
connector M49 terminal 15 (P).
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness as necessary.
6. CHECK PBR FEEDBACK SIGNAL
1. Reconnect front air control connector and air mix door motor
(Passenger) connector.
2. Turn ignition switch ON.
3. Check voltage between front air control harness connector M50
terminal 41 (R/W) and ground.
4. Rotate temperature dial (Passenger) through complete range.
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> GO TO 7. 3 - Ground : Approx.5V
LJIA0044E
3 - 2 Continuity should exist.
LJIA0045E
2 - 15 Continuity should exist.
WJIA0549E
41 - Ground : Approx. 0 - 5V
LJIA0047E

TROUBLE DIAGNOSIS
ATC-73
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
7. CHECK PBR FEEDBACK CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect air mix door motor (Passenger) connector M143 and
front air control connector M50.
3. Check continuity between air mix door motor (Passenger) har-
ness connector M143 terminal 4 (R/W) and front air control har-
ness connector M50 terminal 41 (R/W).
OK or NG
OK >> Replace air mix door motor (Passenger). Refer to AT C -
154, "FRONT AIR MIX DOOR MOTOR (PASSENGER)"
.
NG >> Repair or replace harness as necessary.
DIAGNOSTIC PROCEDURE FOR AIR MIX DOOR MOTOR (REAR)
1. CHECK RESULT FROM FRONT AIR CONTROL SELF-DIAGNOSIS
Self-diagnosis code 38 is present. Refer to ATC-53, "
A/C System Self-diagnosis Function" .
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. CHECK POWER SUPPLY CIRCUIT FOR AIR MIX DOOR MOTOR (REAR)
1. Turn ignition switch OFF.
2. Disconnect front air control connector M50 and air mix door
motor (Rear) connector B155.
3. Check continuity between front air control harness connector
M50 terminal 27 (GR/R) and air mix door motor (Rear) harness
connector B155 terminal 1 (GR/R) and between front air control
harness connector M50 terminal 28 (L/Y) and air mix door motor
(Rear) harness connector B155 terminal 6 (L/Y).
OK or NG
OK >> Replace air mix door motor (Rear). Refer to ATC-154, "REAR AIR MIX DOOR MOTOR" .
NG >> Repair or replace harness as necessary.
3. CHECK PBR REFERENCE SIGNAL VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect air mix door motor (Rear) connector B155.
3. Turn ignition switch ON.
4. Check voltage between air mix door motor (Rear) harness con-
nector B155 terminal 3 (Y) and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.4 - 41 : Continuity should exist.
WJIA0550E
27 - 1 Continuity should exist.
28 - 6 Continuity should exist.
LJIA0049E
3 - Ground : Approx. 5V
LJIA0050E

ATC-74
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
4. CHECK PBR REFERENCE VOLTAGE CIRCUIT BETWEEN AIR MIX DOOR MOTOR (REAR) AND
FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between air mix door motor (Rear) harness
connector B155 terminal 3 (Y) and front air control harness con-
nector M49 terminal 2 (Y).
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> Repair or replace harness as necessary.
5. CHECK PBR GROUND REFERENCE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between air mix door motor (Rear) harness
connector B155 terminal 2 (P) and front air control harness con-
nector M49 terminal 15 (P).
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness as necessary.
6. CHECK PBR FEEDBACK SIGNAL
1. Reconnect front air control connector and air mix door motor
(Rear) connector.
2. Turn ignition switch ON.
3. Check voltage between front air control harness connector M50
terminal 42 (R/Y) and ground.
4. Rotate rear temperature/mode dial (Front) through complete
range.
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> GO TO 7.3 - 2 Continuity should exist.
LJIA0051E
2 - 15 Continuity should exist.
LJIA0052E
42 - Ground : Approx. 0 - 5V
LJIA0053E

TROUBLE DIAGNOSIS
ATC-75
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
7. CHECK PBR FEEDBACK CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect air mix door motor (Rear) connector B155 and front
air control connector M50.
3. Check continuity between air mix door motor (Rear) harness
connector B155 terminal 4 (R/Y) and front air control harness
connector M50 terminal 42 (R/Y).
OK or NG
OK >> Replace air mix door motor (Rear) ATC-154, "REAR AIR
MIX DOOR MOTOR" .
NG >> Repair or replace harness as necessary.4 - 42 Continuity should exist.LJIA0054E

ATC-82
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
5. CHECK PBR GROUND REFERENCE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between defroster door motor harness connec-
tor M144 terminal 2 (P) and front air control harness connector
M49 terminal 15 (P).
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness as necessary.
6. CHECK PBR FEEDBACK SIGNAL
1. Reconnect front air control connector and defroster door motor
connector.
2. Turn ignition switch ON.
3. Check voltage between front air control harness connector M49
terminal 25 (LG/B) and ground.
4. Change mode between floor, defroster, and panel.
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> GO TO 7.
7. CHECK PBR FEEDBACK CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect defroster door motor connector M144 and front air
control connector M49.
3. Check continuity between defroster door motor harness connec-
tor M144 terminal 4 (LG/B) and front air control harness connec-
tor M49 terminal 25 (LG/B).
OK or NG
OK >> Replace defroster door motor. Refer to ATC-150,
"Removal and Installation" .
NG >> Repair or replace harness as necessary.2 - 15 : Continuity should exist.
WJIA0556E
25 - Ground : Approx. 0 - 5V
WJIA0770E
4 - 25 : Continuity should exist.
WJIA0558E

REFRIGERANT LINES
ATC-173
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
5. Remove the front and rear bumper fascia. Refer to EI-13, "FRONT BUMPER" (front), EI-15, "REAR
BUMPER" (rear).
6. Reposition the front fender protector out of the way. Refer to EI-23, "
FENDER PROTECTOR" .
7. Disconnect the chassis harness connector.
8. Remove the spare wheel and tire.
9. Remove the tailpipe and tailpipe hanger bracket. Refer to EX-3, "
Removal and Installation" .
10. Remove the seatbelt latch anchor. Refer to RSU-25, "
Components" .
11. Remove the front floor heat shield.
12. Disconnect each end of the underfloor rear high- and low-pressure A/C and heater core pipes. Refer to
ATC-164, "
Components" .
CAUTION:
Cap or wrap the joint of the pipes with suitable material such as vinyl tape to avoid the entry of air.
13. Set two suitable jacks at the RH body mount points to support the vehicle body when it is separated from
the RH side of the frame.
14. Remove the RH body mount bolts. Refer to BL-159, "
Body Mounting" .
15. Use the vehicle hoist to lower the RH side of the frame from the RH side of the body [approximately 305
mm (12 in)] until there is sufficient clearance to remove the underfloor rear high- and low-pressure A/C
and heater core pipes from between the body and the frame.
16. Remove the underfloor rear high- and low-pressure A/C and heater core pipes from the back of the vehi-
cle.
INSTALLATION
Installation is in the reverse order of removal.
Refer to ATC-164, "
Components" .
CAUTION:

Replace the O-ring of the high/low-pressure pipe with a new one, then apply compressor oil to it
when installing it.

After charging refrigerant, check for leaks.
Removal and Installation for Refrigerant Pressure SensorEJS002DP
REMOVAL
1. Discharge the refrigerant. Refer to ATC-162, "HFC-134a (R-134a) Service Procedure" .
2. Disconnect the refrigerant pressure sensor electrical connector
and remove the refrigerant pressure sensor from the condenser.
CAUTION:
Be careful not to damage the condenser fins.
INSTALLATION
Installation is in the reverse order of removal.
Refer to ATC-164, "
Components" .
CAUTION:

Be careful not to damage the condenser fins.

Replace the O-ring of the refrigerant pressure sensor with a new one, then apply compressor oil to
it when installing it.

After charging refrigerant, check for leaks.
Removal and Installation for CondenserEJ S00 2DQ
REMOVAL
1. Discharge the refrigerant. Refer to ATC-162, "HFC-134a (R-134a) Service Procedure" .
LJIA0145E

NAVIGATION SYSTEM
AV-67
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
Display with Pushed “SETTING” button
The function of each icon is as follows:
Display Settings
How To Perform Display Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “Display” with "ENTER" button.
Application Items
Brightness/Contrast/Map Back ground
How To Perform Navigation Setting
1. Select “Brightness/Contrast/Map Background”.

Brightness, Contrast and Background are shown at the lower part of the screen, and it can be set with the
joystick.
Display Off
How To Perform Navigation Setting
1. Select “Display Off”.

When setting is turned on (Indicator light ON), the display will be under sleep mode.
SKIA4496E
Icon Description
Display Settings of display can be performed.
Vehicle Electronic Systems Settings of vehicle electrical equipment can be performed.
System Settings Settings of linguistic select, time adjusting and beep sound can be performed.
Navigation Settings and adjusting of navigation can be performed.
Short Menus Easy Mode and Expert Mode can be switched.
Guidance Volume The volume and/or on/off of voice prompt can be controlled by the joystick.
Help (only easy mode) Explanation of navigational functions appear on the display.
SKIA5791E
Icon DescriptionReference
page
Brightness/Contrast/Map Background Brightness, Contrast and Map Background can be set.AV- 6 7
Display Off Display sleep mode ON/OFF can be switched.AV- 6 7
Setting of the under section display The setting status of A/C or AV can be shown. AV- 6 8

AV-68
NAVIGATION SYSTEM
Revision: August 20072004 QX56
Setting of the under section display
How To Perform Under Section Display Setting
1. Select “Setting of the Under Section Display”.

The setting status that is selected from A/C or AV is shown at the lower part of the screen.
Vehicle Electronic Systems
Application Items
How To Perform Navigation Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “Vehicle Electronic Systems”.
System Settings
How To Perform System Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “System Settings”.
Icon Description
Adjust Driver Seat When Exiting Vehicle The driver's seat automatically moves back and returns to the original position.
Lift Steering Column When Exiting Vehicle The steering column automatically tilts up and returns to the original position.
Remote Unlock Driver's Door FirstThis option allows selection of which doors will unlock first during an unlocking oper-
ation.
Keyless Remote Response — HornThis option allows the horn chirp mode when pressing the LOCK or UNLOCK button
on the keyfob to be changed.
Keyless Remote Response — LightsThis option allows the hazard flash mode when pressing the LOCK or UNLOCK but-
ton on the keyfob to be changed.
Auto Re-Lock Time This option allows the length of time before doors auto re-lock to be set.
Sensitivity of Automatic Headlights This option allows the sensitivity of the autolights to be set.
Automatic Headlights Off Delay This option allows the length of time before the autolights turn off to be set.
Speed Dependent Wiper This option allows the driving speed dependent wiper function to be turned on or off.
Return All Settings to Default All settings will return to the initial conditions.
WKIA1802E
SKIA4536E