2004 INFINITI FX35 air condition

NAVIGATION SYSTEM
AV-153
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
2. CHECK REVERSE SIGNAL
1. With the selector lever in R-position, check voltage between
NAVI control unit and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Reverse Signal Check for Display Control UnitAKS00BNI
1. CHECK REVERSE LAMP
1. Turn ignition switch ON.
2. Selector lever into R-position.
Does
“R” in the shift position indicator come on?
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT- 1 2 5 , "
BACK-UP LAMP" .
2. CHECK REVERSE SIGNAL
1. With the selector lever in R-position, check voltage between dis-
play control unit and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or cnnector.
When Malfunctioning Connection Between Display Control Unit and NAVI Con-
trol Unit
AKS00BNJ
1. CHECK NAVI CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
1. Check NAVI control unit power supply and ground circuit. Refer to AV- 1 4 5 , "
Power Supply and Ground
Circuit Check for NAVI Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
Terminals
Condition Voltage (+)
(–)
ConnectorTe r m i n a l
(Wire color)
B207 27 (OR) GroundSelect
leverR-position Approx. 12V
Except R-
positionApprox. 0V
SKIA9498E
Terminals
Condition Voltage (+)
(–)
ConnectorTe r m i n a l
(Wire color)
M75 6 (OR) GroundSelect
leverR-position Approx. 12V
Except R-
positionApprox. 0V
SKIA8942E

NAVIGATION SYSTEM
AV-167
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
Guide Sound is Not HeardAKS00BP7
1. CHECK VOICE GUIDE SETTING

While driving in the dark pink route, voice guide does not operate. (note)

Is volume setting not switched ON?
NOTE:
Voice guide is only available at intersections that satisfy certain conditions (indicated by

on the map). There-
fore, guidance may not be given even when the route on the map changes direction.
YES or NO
YES >> GO TO 2.
NO >> Switch the setting ON and turn the volume up.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector and audio unit connector.
3. Check continuity between NAVI control unit harness connector
B208 terminals 7 (LG), 8 (PU) and audio unit harness connector
M60 terminals 36 (B/R), 34 (W/R).
4. Check continuity between NAVI control unit harness connector
B208 terminals 7 (LG), 8 (PU) and ground.
Ok or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK VOICE GUIDE
1. Connect NAVI control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Check signal between NAVI control unit harness connector
B208 terminal 7 (LG) and 8 (PU) with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace audio unit.
NG >> Replace NAVI control unit.
Screen is Not ShownAKS00BNW
1. CHECK DISPLAY POWER SUPPLY AND GROUND CIRCUIT
Check display power supply and ground circuit. Refer to AV- 1 4 7 , "
Power Supply and Ground Circuit Check for
Display" .
OK or NG
OK >> Replace display.
NG >> Repair malfunctioning parts.7 – 36 : Continuity shold exist.
8 – 34 : Continuity shold exist.
7, 8 – Ground : Continuity shold not exist.
PKIA2906E
7 – 8 : Refer to AV- 1 2 1 , "Te r m i n a l s
and Reference Value for NAVI
Control Unit" .
PKIA2907E

NAVIGATION SYSTEM
AV-173
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
in the unit, display the track of the vehicle on the map screen and compare it with the actual road configu-
ration.

Sample tests
– matching or by GPS>
Perform test pattern 1.
–;
Perform test pattern 1 & 2.
Compare the track of the vehicle on the map screen and the actual road configuration. For fairly accurate
tracking, plotting shall be made every several hundred meters.
–;
Perform test pattern 1 & 2.
Drive on a road of which distance is accurately known (by utilizing distance posts on a highway). Calculate
the rate of change (increased/decreased) of the distance by comparing with the actual distance.
Correction = 1 – A/B
A: Distance shown on the screen
B: Actual distance
YES or NO
YES >>
If adjustment is insufficient, perform adjustment again.

If any error is found in the map, please let us know.

Replace NAVI control unit.
NO >> Limit of the location detection capacity of the navigation system.
Example of Symptoms Judged Not MalfunctionAKS007KH
BASIC OPERATION
VEHICLE MARK
Symptom Cause Remedy
No image is shown. Display brightness adjustment is set fully to
DARK side.Adjust the display brightness.
No guide sound is heard.
Audio guide volume is too low or
too high.Volume control is set to OFF, MIN or MAX. Adjust the audio guide volume.
Audio guidance is not available while the vehicle
is driving on a dark pink route.System is not malfunction.
Screen is too dark.
Motion of the image is too slow.Temperature inside the vehicle is low. Wait until the temperature inside the vehicle
reaches the proper temperature.
Small black or bright spots appear
on the screen.Symptom peculiar to a liquid crystal display. System is not malfunction.
Symptom Cause Remedy
Map screen and BIRDVIEW™
Name of the place vary with the
screen.Some thinning of the character data is done to
prevent the display becoming to complex. In
some cases and in some locations, the display
contents may differ.
The same place name, street name, etc. may not
be displayed every time on account of the data
processing.System is not malfunction.
Vehicle mark is not positioned cor-
rectly.Vehicle is transferred by ferry or by towing after its
ignition switch is turned to OFF.Drive the vehicle for a while in the GPS sat-
ellite signal receiving condition.
Screen will not switch to nighttime
mode after the lighting switch is
turned ON.The daytime screen is selected by the “SWITCH
SCREENS” when the last time the screen dim-
ming setting is done.
Switching between daytime/nighttime screen may
be inhibited by the automatic illumination adjust-
ment function.Perform screen dimming and select the
nighttime screen by “SWITCH SCREENS”.
Map screen will not scroll in accor-
dance with the vehicle travel.Current location is not displayed. Press “MAP” button to display the current
location.
Vehicle mark will not be shown. Current location is not displayed. Press “MAP” button to display the current
location.

AV-178
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
PlaceIn a parking lot When driving in a parking lot, or other loca-
tion where there are no roads on the map,
matching may place the vehicle mark on a
nearby road. When the vehicle returns to
the road, the vehicle mark may have devi-
ated from the correct location.
When driving in circle or turning the steer-
ing wheel repeatedly, direction errors accu-
mulate, and the vehicle mark may deviate
from the correct location.
If after travelling about 10km
(6miles) the correct location
has not been restored, perform
location correction and, if nec-
essary, direction correction. Turn ta ble
When the ignition switch is OFF, the navi-
gation system cannot get the signal from
the gyroscope (angular speed sensor).
Therefore, the displayed direction may be
wrong and the correct road may not be
easily returned to after rotating the vehicle
on a turn table with the ignition OFF.
Slippery roads On snow, wet roads, gravel, or other roads
where tires may slip easily, accumulated
mileage errors may cause the vehicle mark
to deviate from the correct road.
Slopes When parking in sloped garages, when
travelling on banked roads, or in other
cases where the vehicle turns when tilted,
an error in the turning angle will occur, and
the vehicle mark may deviate from the
road.
Map dataRoad not displayed on the map screen
When driving on new roads or other roads
not displayed on the map screen, map
matching does not function correctly and
matches the location to a nearby road.
When the vehicle returns to a road which is
on the map, the vehicle mark may deviate
from the correct road.
Different road pattern
(Changed due to repair)
If the road pattern stored in the map data
and the actual road pattern are different,
map matching does not function correctly
and matches the location to a nearby road.
The vehicle mark may deviate from the
correct road.
Vehicle Use of tire chainsWhen tire chains are used, the mileage is
not correctly detected, and the vehicle
mark may deviate from the correct road.Drive the vehicle for a while. If
the distance is still deviated,
adjust it by using the distance
adjustment function. (If the tire
chain is removed, recover the
original value.) Cause (condition) –: While driving ooo: Display Driving condition Remarks (correction, etc.)
SEL709V
SEL710V
SEL699V
ELK0201D

INFINITI MOBILE ENTERTAINMENT SYSTEM
AV-191
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
DVD Player Is Not WorkAKS00BOZ
1. CHECK FUSE
Make sure that the following fuse of the DVD player are not blown.
OK or NG
OK >> GO TO 2
NG >> If fuse is blown be sure to eliminate case of problem before installing new fuse, refer to PG-3,
"POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between DVD player harness connector terminals
and ground.
OK or NG
OK >> GO TO 3
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect DVD player connector.
3. Check continuity between the following DVD player harness
connector B19 terminal 22 (B) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
Unit Signal Fuse NO.
DVD playerBattery power supply 32
ACC power supply 6
Terminals
Condition Voltage (+)
(-)
ConnectorTerminal
(Wire color)
M7316
(W/L)
GroundIgnition switch
OFFBattery voltage
15
(LG/R) Ignition switch
ACCBattery voltage
SKIB0323E
22 – Ground : Continuity should exist.
SKIA5846E

AV-192
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2004 November 2004 FX35/FX45
4. CHECK HARNESS
1. Disconnect audio unit connector.
2. Check continuity between DVD player harness connector M73
terminals 9 (Y/B), 11 (L/W) and audio unit harness connector
M65 terminals 38 (Y/B), 40 (L/W).
3. Check continuity between DVD player harness connector M73
terminal 9 (Y/B), 11 (L/W) and ground.
OK or NG
OK >> GO TO 5
NG >> Repair harness or connector.
5. CHECK CONTROL SIGNAL
1. Connect DVD player connector and audio unit connector.
2. Turn ignition switch ACC.
3. Check voltage between DVD player harness connector M73 ter-
minal 9 (Y/B) and ground.
OK or NG
OK >> GO TO 6
NG >> Replace DVD player.
6. CHECK CONTROL SIGNAL
1. Check voltage between DVD player harness connector M73 ter-
minal 11 (L/W) and ground.
OK or NG
OK >> Replace DVD player.
NG >> Replace audio unit.9 – 38 : Continuity should exist.
11 – 40 : Continuity should exist.
9, 11 – Ground : Continuity should not exist.
SKIB0513E
Terminals
Condition Voltage (+)
(-)
ConnectorTerminal
(Wire color)
M739
(Y/B)GroundPush “power”
switch of DVD-
player Approx. 5V
SKIB0326E
Terminals
Condition Voltage (+)
(-)
ConnectorTerminal
(Wire color)
M7311
(L/W)GroundPush “power”
switch of DVD
playerApprox. 5V
SKIB0328E

AV-194
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2004 November 2004 FX35/FX45
Screen is not Shown (Sounds Come Out of Both an Audio Speaker and a Head
Phone)
AKS00BP1
1. CHECK HARNESS
1. Disconnect DVD player connector and DVD display connector.
2. Check continuity between DVD player harness connector B19
terminals 23 (OR), 24 (W) and DVD display harness connector
B192 terminals 7 (OR), 8 (W).
3. Check continuity between DVD player harness connector B19
terminals 23 (OR), 24 (W) and ground.
OK or NG
OK >> GO TO 2
NG >> Repair harness or connector.
2. CHECK VIDEO SIGNAL
1. Connect DVD player connector and DVD display connector.
2. Turn ignition switch ACC.
3. Check the signal between DVD player harness connector B19
terminals 23 (OR) and 24 (W) with CONSULT-II or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace DVD player.
3. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD player connector and DVD display connector.
3. Check continuity between DVD player harness connector B19
terminal 29 (GY) and DVD display harness connector B192 ter-
minal 13 (GY).
4. Check continuity between DVD player harness connector B19
terminal 29 (GY) and ground.
OK or NG
OK >> GO TO 4
NG >> Repair harness or connector.23 – 7 : Continuity should exist.
24 – 8 : Continuity should exist.
23, 24 – Ground : Continuity should not exist.
SKIB0516E
Te r m i n a l
Condition Reference value
(+) (-)
23 24 Play DVD videoRefer to AV- 1 8 8 , "
Te r m i -
nals and Reference Value
for DVD Player" .
SKIA7050E
29 – 13 : Continuity should exist.
29 – Ground : Continuity should not exist.
SKIB0333E

AV-198
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2004 November 2004 FX35/FX45
3. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD player connector and audio unit connector.
3. Check continuity between DVD player harness connector M73
terminals 1 (L), 2 (R), 3(LG), 4 (PU) and audio unit harness con-
nector M65 terminals 37 (L), 39 (R), 43 (LG), 42 (PU).
4. Check continuity between DVD player harness connector M73
terminals 1 (L), 2 (R), 3 (LG), 4 (PU) and ground.
OK or NG
OK >> GO TO 4
NG >> Repair harness or connector.
4. CHECK MES SOUND SIGNAL
1. Connect DVD player connector and audio unit connector.
2. Turn the ignition switch ACC and push “POWER” switch of DVD
player.
3. Check the signal between DVD player harness connector M73
terminals 1 (L) and 2 (R), 3 (LG) and 4 (PU) with CONSULT-II or
oscilloscope.
OK or NG
OK >> Replace audio unit.
NG >> Replace DVD player.
Removal and Installation for DVD PlayerAKS00BP5
REMOVAL
1. Remove center console. Refer to IP-12, "(H) Center Console" .
2. Remove center console rear finisher. Refer to IP-18, "
CENTER
CONSOLE" .
3. Remove screws (2) with power tool and remove DVD player.1 – 37 : Continuity should exist.
2 – 39 : Continuity should exist.
3 – 43 : Continuity should exist.
4 – 42 : Continuity should exist.
1, 2, 3, 4 – Ground : Continuity should not exist.
SKIA7034E
Te r m i n a l
Condition Reference value
(+) (-)
12
Play CD or DVD videoRefer to AV- 1 8 8 , "
Te r m i -
nals and Reference Value
for DVD Player" . 34SKIB0518E
SKIA5810E