2004 DACIA SUPERNOVA wheel

DRIVE SHAFTS
29
FRONT TRANSVERSAL TRANSMISSION
DISMOUNTING - THE SIDE TO WHEEL
Loosen the left wheel screws.
Lift the vehicle on an elevator with two columns.
Di smount the wheels.
Di smount the scre ws that attach the brake disk assembly on the steering knuckle.
Un screw the transmission nut by means of the RO 604 – 01 device.
Di smount :
- the nut of t he steering ball joint;
- steering ball joint from the steering knuckle, by means of the PF 476 extractor; the
attachment screws of the steering knuckle on the shock absorber end. S
PECIAL TOOLS
- RO 604-01 Hub immobilizing device
- PF 476 Ball joint extractor
TIGHTENING MOMENTS (daN/m)
- Transmission nut 21\
- Screw for fixing the bellows lid on the gearbox 2,5
- Wheels attachment screw 7,5
- Screws, nuts for fixing the steerin g knuc kle on the shock absorber 7,5
- Screw for fixing the caliper on the steeri ng knuckle 6,5
- Nut for steering ball joint 4
Pu sh the transmission in the steering knuckle and incline the latter.
Di smount the transmission, the wheel side.
29 - 1
vnx.su

DRIVE SHAFTS
29
FRONT TRANSVERSAL TRANSMISSION
REMOUNTING – THE SIDE TO THE GEARBOX
The left side
Engage the t ransmission GI joint in the ge arbox (the transmission position as horizontally
as possible).
Mount the thre e attachment screws of the bellows lid on the gearbox.
The right side
Grease the t ulip fra me grooves (the grooves area) and t he tra nsmission shaft of t he
gearbox with transmission oil.
Engage the transmission GI joint (the tulip) on the transmission shaft of the gearbox
(the tra nsmission position must be as horizontally as possible).
REMOUNTING – THE SIDE TO THE WHEEL
For both sides
Engage the transmission in the steering knuckle, this one being necessary to freely enter,
so that threaded area of the steering knuckle is allowing to remounting the transmission nut.
Pe rform then the dismounting opera tions in the reverse orde r.
Ob serve the tightening moments.
Remount the brake disk assembly.
Refill the gearbox with oil.
Pr ess several times the brake pedal to enable caliper piston coming in contact with the
brake pads.
29 - 3
vnx.su

DRIVE SHAFTS
29BELLOWS-BEARING ASSEMBLYTO THE GEARBOX
M aintaining the transmission on the press, on both sides, shall be ensured on the G
groove made on shaft, by means of a device type FACOM U 53 G, ( the flat side towards
bellows) in order t o avoid the defl ector damages on the wheel side. The pressing effort of the beari ng on the tra nsmission shaft ahas the value of = 100 –
700 daN. Press again the assembled tripod on the tra nsmission shaft observing the marks made
when depressing. The pre ss effort of t he tripod assembly on t he groove d area of t he shaft end, shall be
between 60 – 600 daN. Remount the blocking ring (Zeger lock) in the groove made on the tra nsmission shaft.
29 - 6Left
transmi ssion
G
vnx.su

DRIVE SHAFTS
29
BELLOWS TO WHEEL
JOINT TOWARDS WHEEL
1. Steeri ng knuckle casing ass.
2. Retainer star
3. Tripod to the wheel
4. Tulip shaft
5. Maintaining collars
6. Rubber protection bellow S
PECIAL TOOLS
GE 86 joint bellows replacement device PF 537-03
DISMOUNTING
Dismount the two maintaining collars
off t he be l lows by means of t wo rods,
locally manufactured (see the dra wing) Cut and remove the damaged bellows.
Remove as much grease as possible.
Mark one of the groove routes of the shaft
subject to its working corresponding clog by
marking w ith a centre punch on casing outer
conse quently on the shaft.
Detach th e connection be twe en the
transmission shaft and the steering knuckle
casing, lift ing one by one the arms of the
reta ining star from the three stamps performed
on the pe tals of the shaft tulip.
WHEN DISMOUNTING, DO NOT DEFO RM
THE ARMS OF THE RETAINING ST AR
Retrieve the head and the spring from the
tripod to wheel.
29 - 7
Left
transmi ssion
vnx.su

DRIVE SHAFTS
29BELLOWS TO WHEEL
REMOUNTING
The mounting of the new bellows is to be
pe rform e d by m e a ns of t he PF 573 – 03
device.
Catch the inclined transmission in a vice
w ith soft jaws in ord er to avoid the sha ft
damaging. Engage t he PF 537 – 03 device over t he
tulip of the transmission shaft.
Obturate the small e xtremity of the bellows
and, abundantly grease with automatic
transmission oil or ELF CARDREXA RNT
2 grease: - the all outer surface of t he PF 537 – 01
device - the inner part of t he bellows, especially
its smaller diameter part (this operation is
performed for slipping help).
29 - 8
Left
transmi ssion
vnx.su

DRIVE SHAFTS
29
BELLOWS TO WHEEL
Introduce the smaller di ameter of the
bellows on the PF 537 – 03 device.
Cove r a ha nd with c lean ga uz e a nd
place it on the bellows in such a way as to
str etch the first fol d.
T ake support with the hip on the edge
of the vice (latera l side). Place the ot her hand around the first one
and strongly pull it, taking c are that first
fold is not huddled together. Bring the bellows a s close as possible
to the device cylindri cal par t and l et i t
release till half stroke. It is recommended to perfo rm many
times this opera tion (m aximum 5 times). When e asy slipping i s noticed, make so
that bellows is passing ove r the de vice
cylindrical part, the operation being
performed without stopping.
29 - 9
Left
transmi ssion
vnx.su

DRIVE SHAFTS
29BELLOWS TO WHEEL
Catch the steering knuc kle c asing in a vice
with soft jaws. Put the spri ng a nd he a d i n t he t ri pod
groove.
Brings the clogs to the center.
Position the retaining star (s), and each of
its arm s, being at the bi secting lines of t he
angles formed by the tri pod arms.
Int roduc e the tra nsm ission sha ft i n the
s teering knuckle casing, positioning it, subject
to the m arks (the t hree c logs penetrating in
the thre e rolling routes of the shaft). Slide slowl y t he t ransm i ssi on sha ft, i n
order to engage one arm of the re taining star
in the marked poi nt of the transmission shaft,
and press it for correct centeri ng.
Placing the other re taining star t wo arms,
it will be made easy by a screwdriver, with its
end modifi ed as per dra wing:
A = 5 mm B = 3 mm
Ensure that retaining star arms are correctly
positioned in the shaft marks. Check by hand, the joint operation.
Must not exist any hard point.
Di stribute in the bellows and in the steering
knuckle casing the gre ase pre scribed dosage.
NOTE It is obligatory to observe the quantity and
type of t he prescribed grease, 2 l +1 c l, ELF
CARDREXA RNT 2.
29 - 10
Left
transmi ssion
S
vnx.su

DRIVE SHAFTS
29
BELLOWS TO WHEEL
Po sition t he two be l l ows be ads i n t he groove s of t he st e e ri ng knuc kl e c asi ng,
consequently on the transmission shaft tube. Place a non-cutting, round headed rod between the transmission shaft and the bellows
in order to dose the amount of air inside. Mount the two collars, by means of the two rods used also at t he di smounting ope ration.
29 - 11
Left
transmi ssion
vnx.su