Page 156 of 933
E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 66
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
STARTING PROBLEMS
1.
Do not use this information before having done the complete check-up
with the tester!
SUGGESTIONS
♦♦
♦♦
Check if there is petrol in the fuel tank (do not rely on the
on-board in
dices). Check if it is the fuel recommended by
the manufacturer.
Disconnect the tube between the draining valve and the
intake collector and strangle it up. If the disturbances disap-
pear, the cause was the draining valve.
Connect the “CLIP TEHNIC” device to do this test in ac-
cordance with the usual manner of work.
Connect the tester “CLIP” and do the test corresponding to
the check-up of the rotation signal.
Gently touch the step-by-step engine in order to possibly
unbloc k it.
Check the fuel
Check the canister
draining valve♦♦♦♦
Check the engine
co
mp ression
Check the
engine flywheel
Check the step-by-
step engine
♦♦ ♦♦
♦
♦
Check if there are no broken tubes.
Check the state of the sparking plugs and the ignition coil.
Check the tubes and
hoses
♦♦♦♦
Check the ignition♦♦♦♦
Check the flow and the pressure of the fuel: the condition
of
the petrol-pump, of the pressure regulator. Check the
injectors (flow, shape of jet)
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.
Check the fuel-
supply circuit
♦♦♦♦
Check the exhaust
system
♦♦♦♦
vnx.su
Page 157 of 933
E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 67
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
IDLE MODE PROBLEMS
Do not use this information before having done the complete check-
up w ith the tester!2.
SUGGESTIONS
Check if there is petrol in the fuel tank (do not rely on the
on-board indi ces). Check if it is the fuel recommended by
the manufa cturer.
Check the fuel
Check if there are no broken tubes.
Check the tubes and hose
s.
♦
♦
Check the state of the sparking plugs and the ignition coil.
Check, on the o il ga uge , if the le ve l of the oil is not too h igh.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Gently touch the step-by-step engine in order to possibly
unblock it.
Check the condition of the fittings.
Check, after taking them apart, whether the injectors leak.
Check if the clapper body is not clogged.
Check the ignition
Check the engine oil level
Ch eck the step-by-step engine
Check the intake collector
Check the injectors
Ch eck the body of the clapper
♦
♦
Check the engine flywheel♦
♦
♦
♦
♦
Check the flow and the pressure of the fuel: the condition
of the pe trol-pump, of the pressure regulator. Check the
injectors (flow, shape of jet)
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.
Check the fuel-supply
circuit
Check the exhaust system
♦
♦
A
vnx.su
Page 160 of 933
E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 70
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
Check if the clapper body is not clogged.
Check if there are cases of lack of watertightness (noise)
on the powe r-brakes.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Check if the spurs, the brake cylinders and the wheel ball-
rings are no t seized-up.Check the body o f
the clapper♦
Ch eck t he power-br akes
Check the engine
flywheel
Check the running
train
Check the cooling
of the engine
♦
♦
♦
Check if there is enough engine cooling.♦
Check the canister
draining valve Disconnect the tube between the draining valve and the in-
take collector and strangle it up. If the disturbances disap-
pear, the caus
e was the draining valve.
Check the engine
comp ression Connect the “CLIP TEHNIC” device to do this test in accor-
dance w ith the usual manner of work.
AFTER REPAIR Erase the defec
ts memorized. If there are no other problems,
eras e the parameters memorized by the calculator.
♦
♦
A
vnx.su
Page 172 of 933
19 - 12
19
COOLING - EX HA U ST - FU EL TANK
DISMOUNTING
The car is set on a two-column lifting stand.
The ba ttery is disconnected.
Th e co oling circuit is emptied at the filling stopper placed at the lower part of the radiator.
The fo llowing are taken apart.
- the distribution belt (see Chapter “ Distribution belt”) ;
- the ex tending pulley / runner (1);
- the fixing screws of the water-pump.
The water-pump is taken out at the upper end of the engine compartment.
SPECIAL DEVICES
MOT. 1202-02 Pincers for elastic collars
MOT. 1505 Device for measuring the belt tension
TIGHTENING COUPLES (daNm)
Screw-nut for extending pulley / runner 5
Screw for the crankshaft pulley 2+68
o+/-6o
Screws for right-side pendular stand 6.2
Screw-nut for hydro-elastic buffer 4.4
Screws for water-pump 2.2
Screw-nuts for water-pump 1
Screws for wheels 7.5
WATER PUMP
vnx.su
Page 180 of 933
19 - 20
19
COOLING - EX HA U ST - FU EL TANK
DIS M OUNT ING
In order to take apart the petrol tank from the car the following opera tions are in order:
The battery i s disconnected;
The tank is emptied of fue l;
The carpet in the boot is taken out;
The cabling case of the fuel-level transmitter i s taken off;
The collar fi xing the airi ng conduit on the tank lid is taken off;
The junctures of t he fue l-supply c onduits (goi ng- and return-) are taken off t he tank lid;
The driving axis of the spare-wheel stand is taken off;
The car is suspended on an elevator;
The spare-wheel is taken out of i ts holder;
The scre ws fixing the protection screen of the tank, and then the tank itself, are taken
off; The collars fixing the anti-t ilt valve juncture are taken off.
R
EMOUNTING
It is done in the reverse orde r of the taking apart opera tions. T
ANK FUEL
vnx.su
Page 191 of 933
20
CLUTCH
CLUTCH DISC MECHANISM
REPLACEMENT
This operation is done after taking apart the engine - gearbox ensemble and after
their separation.
The stopping sector MOT 582 is mounted.
The screws fixi ng th e mechan ism are taken off.
The mechan ism and the clutch disc are taken apart.
Visual inspection is done: - wear of engi ne flywheel;
- co ndition of the starter crown;
- watertightness at the level of the crankshaft fitting;
- co ndition of the flywheel surface (it must not have scratches).
The fau lty parts are replaced and the grooves of the clutch shaft are cleaned.
SPECIAL DEVICES
MOT 582 Flywheel immobilizing sector
AMB 1518 Clutch centering device
TIGHTENING COUPLES (daNm)
Clutch mechanism screws 2
20 - 9
vnx.su
Page 192 of 933
20
CLUTCH
The clutch disc is mounted with the A damping flange towards the gearbox
The clutch d isc is centered with the AMB 1518 centering device
The clutch mech anism is mounted;
Th e fixing screws are progressively put on the thread of the mechanism, then they are tight-
ened to the couple;
The MOT 582 fly wheel-stopping sector is taken off.
CLUTCH DISC MECHANISM
20 - 10
vnx.su
Page 212 of 933
CV JH3 - 05021
MANUAL GEARBOX
21 - 20
The differential of the
JH3050 gearbox is the simple type (with two satellite s and two planetary
wheels, one of which making a common body with the tulip of the planetary transmission).
This differential is supported in the clutch – differential crankcase by means of two cylindrical
bearings equipped with balls of various sizes.
The two bearings are pressed in the clutch – differential crankcase.
The crown of the main transmission is assembled by hooping, on the differential crankcase.
DIFFERENTIAL DISMOUNTING
This operation is performed after separating the crankcases. The zero ring (1) is removed from the right planetary shaft, then by means of a pins extractor
and a hammer, the sealing gasket (2 ) is gently hit with a hammer in order to make it pivoting.
The oil seal ring is carefully pulled along the grooved part of the planetary pinion in order
not to deteriorate the grooves.
GEARBOX DISMOUNTING
DIFFE RENTIAL
vnx.su
