2004 DACIA SUPERNOVA wheel

ENGINE E7J-A-2/6010
10 - 30
ENGINE AND LOWER ENGINE UNITS
Mount the lower c asing and tighten the scre ws at a moment of 1daNm.
The watertight-sealing is done with RHODORSEAL 5661; girdle D must be 3 mm thick.
Do not forget to replace the two crescent-shaped fittings (in the A are a) with new
ones.
-the fl ywheel: beforehand oil t he face for t he pl acing of the flywheel on the crank-
s haft, using LOCTITE AUTOFORM; apply on the screws one drop of LOCTITE
FRENETANCH and tighten them at 5 - 5.5 daNm, after having blocked the flywheel
by means of the cogged sector MOT 582.
-the clutch (be cautious about the centring): scre ws are tightened at 2 daNm;
-the water-pump (the watertight-sealing is done with LOCTITE 518, the H girdle
must be of 0.6 - 1 mm). The screws are tightened at a couple of 1 - 2 daNm.
LOWER CASE
RE-MOUNTING
THIS OPERATION IS ALSO VALID IN CASE THE CRANKCASE IS RE- MOUNTED ON THE CAR (SEE PAGE 10-36)
RECO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 37
ENGINE AND LOWER ENGINE UNITS
TIG H TENING CO UPL E S (daNm)
Screws for fixing at front of motor-propelling frame 6.2
Screws for fixing at back of motor-propelling fram 10.2
Lower crankcase screws 1
Screws for fixing steering wheel lower axis 1.4
Screws of wheel 7.5
Screw of the ball-and-socket joint 5.5
Screw-nut of the steering ball-and-socket joint 3.5
Screw for fixing anti-swing auxiliary connecting rod (on frame) 6.2
Screw for fixing anti-swing auxiliary connecting rod (on gearbox) 10.5
D
IS M O UNT ING
The c ar i s placed on a l ifting stand with
two columns; The battery i s disconnected;
The engine is emptied of oil;
The engine-shield is taken apart ;
To take apart :
-front wheels;
-screw-nut for fixing the lower steer-
ing wheel axis on the pinion of t he steer-
ing case; -the steering ball-and-socket joints
and the arm ball-and-socket joints; -side clearance devices;
-thermic protection screen;
-catalytic convert er;
-front bumper ba r;
-anti-swing auxiliary connecting rod.
The screws for fixing the motor-propelling
s et fra me are taken a part, and the frame is
lowered; The lower c rankcase is taken apart.
R
E-MOUNT ING
The lower c rankcase is cleaned.
A ca. 3 mm-thick girdl e of RHODERSEAL
5661 is applied, as in the adjoining drawing. Do not forget to replace the two cres-
cent-sha ped fitti ngs at the e nds of the
crankcase.
Mind that the relative displacement be-
tween the lower crankcase and the cylin-
d er crankcase, along the gearbox-assem-
b ly surface, should not exceed 0.3 mm.
LOWER CRANKCASE MOUNTED ON THE CAR
LOWER CRANKCASE
vnx.su

ENGINE E7J-A-2/6010
10 - 39
ENGINE AND LOWER ENGINE UNITS
TIGHTENING COUPLES (daNm)
Screws for fixing combustion-head cap1
S crew-nut for stretching distribution belt runner/pulley 5
Screws and screw-nuts M 6 for water-pump 1
Screws and screw-nuts M 8 for water-pump 2.2
Screw of the crankshaft pulley 2+68
o+/-6o
Screw of cam-shaft pin 4.5
Screws of rocker-arm ramp 2.3
S crews of flywheel 5 - 5.5
Screws of oil-pump 2.5
Screws of oil-pump cap 1
Screws of bearing caps 2.5+43
o+/-6o
Screws of combustion-head 2+97o+/-2o
Screws of the exhaust gallery 2.5
Screws of the intake gallery 2.5
Sparking plugs 2.5 - 3
Screws of the oil-crankcase 1
Screws for rocker-arm adjustment 1.5
Emptying jack 2
S crews of the connecting rod caps 4.2
Oxygen probe 4.5
TIGHTENING COUPLES
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
Tightening couples (daNm)
Screws of wheels7.5
Screw of the crankshaft pulley 2+68
o+/-6o
S crew-nut of stretching runner 5
Screws right-side stand 6.2
Screw-nut hydroelastic buffer 3.7
DISMONTING
The car is placed on a lifting stand.
The fore part of the engine is proppe d
on the frame using the MOT.545 device.
The following are taken apart: -front right-side wheel;
-the right-side pendular suspension;
11 - 1 -the alterna tor belt;

-the carrying belt of the compressor
(AC) ;
-the pulley of the crankshaft and its hub;
-the carryi ng pulley of the compressor;
-the distri bution crankcases.
DIS TRIBUTION BELT
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
SPECIAL TOOL- AND-CHECK SETS
MOT.1202-01 -”CLIC” collar-pincers
MOT.1505 -Device for measuring belt tension
MOT.484 -Device for jacket maintaining -Wrench for angular tightening
-Pincers for elastic collar
TIG H TENING CO UPL E S (daNm )
S crew-nut of stretching runner/pulley 5
Screw of crankshaft pulley 2+68
o+/-6o
Screws of pendular suspension stand 6.2
Screw-nut of hydro-elastic buffer 3.7
Wheel Screws 7.5
Co mbustion-head Screws 2+97
o+/-2o
To take apart :
-the connector of the induction coil;
-the fue l hoses (t he going- and re -
turn circ uit); -the connectors of the injectors;
-the plugs of the sparks;
-the induction coil.
11 - 3
CYLINDER HEA D FITTING
D
IS M O UNT ING
The car is placed on a two-column lift -
ing stand; The battery i s disconnected;
The cooling circuit is emptied at the
jack situated at the lower pa rt of the radia-
tor; The distribution belt is taken apart (see
Chapter Distri bution Belt);
The following are taken apart: -air-filter;
-the c onnector of the c lapper-posi-
tion potentiometer (1); -the acceleration cable;
-the connector of the atmosphe ric
pressure sensor (2);
-the co nnector of the step-by-step
engine (3); -the connector of t he air temperature
sensor (4) on the intake collector;
vnx.su

16E7J-A-2/60 ENGINE
16 - 6
ST ARTING AND CHARGING
DIS M O UNT ING
(in the air -conditioning variant)
The car is placed on a two-column lifting stand;
The electric connections are uncoupled from the battery;
The following are taken apart: -the top scre w of the alternator;
-the belt of the alternator;
The right-side front wheel of the car is taken apart;
The car is suspended;
The two screws fixing the shock-absorber on the steeri ng swivel stand are taken off;
The steeri ng swivel stand is lowered and the right-side planetary tra nsmission is taken
off the planetary pi nion of the gearbox; The electric conductors of the alternator a re disconnected;
The screw of the alternator is taken off;
The alterna tor is taken apart laterally past the right-side planetary tra nsmission.
R
E-MOUNT ING
The taking-apart opera tions are done in the reverse order;
The carrying belt of the alternator is stretched to obtain the mounting tension recom-
mended (263 Hz +/- 10% );
The position of the alternator i s blocked;
The engine is revolved thre e and a half cra nkshaft turns;
The reading end of the MOT. 1505 measuring device is placed in the measuring area;
The tension in the belt is measured;
It is checked whether t his fits into the mounting tension tolera nce; if not , the belt will be
str etched again until the re commended tension ( 263 Hz +/- 10%) is reached.
The i nspection and the adjustment of the belt are done with the engine at ambient
temperature .
Tighten at the require d moment, the alternator a ttachment screws :- screw M10 (lower attachment)-5 daNm
-screw M10 (upper attachment)-2.2 daNm.
Remark: Once dismounted, a belt is not to be remounted, but replaced.
AL TERNATOR
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 29
DIAG
NOSING-INTERPRETING THE DEFECTS
DEF ECT
PRE SEN TOR
MEMORIZEDINFORMATION ROTATION SENSOR
1. Faulty cogs of the engine flywheel
2. Absence of flywheel signal.
In orde r to do this type of diagnosing, the sensor for atmospheric pressure
mu st not be faulty
Conditions of breakdown detection by the calculator:
-the contact is taken and the dialogue with the calculator is waited for to
be lo st, then the dialogue with the calculator is re-entered and the memo-
rized defec ts are erased
-opera te the starter for 10 seconds or start the engine and keep it in idle
m ode.
Condition of performing the diagnosing:
-defec t is present
-the defect has been memorized but is recorded in the “present” state.
Check the connection and the state of the rotation sensor
Change the connector if necessary.
Check the resistance of rotation sensor.
Remedy rotation sensor if necessary.
Connect the 90-way terminal-tester instead of the calculator and check the insulation, the
continuity and the absence of contact resistance along the circuits:
pin 54 of calculator
♦ pin A of rotation sensor
pin 24 of calculator
♦ pin B of ro tation sensor.
Remedy if necessary.
Check the condition of the cogs of the engine flywheel.
Change the rotation sensor if the incident persists.
The proble m is not yet solved! Consequently, the injection calculator must be changed.
CAUTION! The destruction of the calculator has probably been caused by an electric shock.
The cause of the destruction must be found before mounting a new
calcul ator.
Er ase defects memorized by the computer.
Perform the steps under “Suggestions” to confirm the repair.
Remedy other possible defects.
AFTER
R EPAIR
12.
SUGGESTIONS
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 47
DIAG
NOSING-INTERPRETING THE DEFECTS
POLLUTING COMBUSTION MISFIRE
DESTRUCTIVE COMBUSTION MISFIRE
1. Combustion misfire during the last running done
2. Confirmed combustion misfire.DEFECT
PR ESENT
Combustion misfire at cylinder 1
Combustion misfire at cylinder 2
Combustion misfire at cylinder 3
Combustion misfire at cylinder 4.
Furnishe s informa tion c onc e rning the na ture and loc ation of bre a kdown.
SUGGESTIONS
31.
Connect the tester and select “Test of ignition”.
Watch the indications and replace the necessary parts.
Connect the tester and select “Test of compression”.
Watch the indications and replace the necessary parts.
Connect the tester and check the cogs of the flywheel.
Remedy if necessary.
If no defect is found ou
t, then there is a problem with the fuel-supply circuit. You must
check:
-p etro l filter
-f low and pressure of fuel
-condition of petrol pump
- if there are impurities inside the tank
-condition of injectors.
Remedy the elements of the fuel-supply circuit that are faulty.
Note down other functional defects.
Erase the defec ts memorized by the calculator.
Remedy other possible defects.
AFTER REPAIR
vnx.su