2004 DACIA SUPERNOVA air conditioning

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 43
DIAG
NOSING-INTERPRETING THE DEFECTS
LOW SPEED VENTILATOR RELAY COMMAND CIRCUIT
(for A.C. cars)
1. Open circuit or short-circuit to mass of the way to pin 8 of the calcu- lator
2. Short-circuit at 12 V along the way to pin 8 of the calculator.DEFECT
PR ESENT27.
Conditions of breakdown detection by the calculator:
-take the contact and wa it for the dialogue with the tester to be lost
-set the conta ct and enter dialogue.
Condition of performing the diagnosing:
-defec t is present
Note: this defect has to be correlated with the diagnosing of the water
temperature sensor circuit and the air-conditioning installation.
SUGGESTIONS
Check the connection and the condition of the low-speed 700 ventilator connector
Change the connector if necessary.
Check, after setting contact, the presence of +12 V at pole 1 of the 700 relay.
Remedy it if necessary.
Connect the 90-way terminal-tester instead of the calculator and check the insulation
and the co ntinuity along the circuit:
pi n 8 of calculator
♦ po le 2 of the low-speed 700 ventilator relay.
Remedy if necessary.
Check the coil of the low-speed 700 ventilator relay.
Change relay if necessary.
The problem is not yet solved! Consequently, the injection calculator must be changed.
CAUTION! The destruction of the calculator has probably been caused by an electric shock.
The cause of the destruction must be found before mounting a new
calcul ator.
AFTER
REPAIREr ase defects memorized by the computer.
Perform the steps under “Suggestions” to confirm the repair.
Remedy other possible defects.
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 44
DIAG
NOSING-INTERPRETING THE DEFECTS
HIGH SPEED VENTILATOR RELAY COMMAND CIRCUIT
(for A.C. cars)
1. Open circuit or short-circuit to mass of the way to pin 38 of the calculator
2. Sh ort-circuit at 12 V along the way to pin 38 of the calculator.DEFECT
PRESENT
Conditions of breakdown detection by the calculator:
-take the contact and wait for the dialogue with the tester to be lost
-set the conta ct and enter dialogue.
Condition of performing the diagnosing:
-the defe ct is present
Note: this defect has to be correlated with the diagnosing of the water
temperature sensor circuit and the air-conditioning installation.
S UGGESTIONS
Check the connection and the condition of the high-speed 234 ve n tilator co n nector
Change the connector if necessary.
Check, after se tt i ng co ntact, the presence of +12 V at po le 1 of the 234 re la y .
Remedy it if necessary.
Connect the 90-way terminal-tester instead of the calculator and check the insulation
and the con ti nui ty alo ng the circui t:
pin 38 of calculator
® pole 2 of the low-speed 234 ve nt il a to r relay.
Remedy if necessary.
Check the co i l of the lo w- sp e ed 23 4 ventilator relay.
Change re la y if necessary.
The problem is not yet solved! Consequently, the injection calculator must be changed.
CAUTION! The destruction of the calculator has probably been caused by an
ele ct ric sho ck.
The cause of the destru ction must be found before mounti ng a new
calcu lato r.
Er ase defects memorized by the computer.
Perform the steps under “Suggestions” to confirm the repair.
Remedy other possible defects.AFTER
R EPAIR
28.
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 50
DIAGNOSING-CON
FORMITY TEST
LIST OF PARAMETERS
5.Water te m-
perature sen-
sor Parameter
: water
temp erature X= Eng ine
temperature +/- 50C
If further problems
arise, refer to the diag-
no sing of that parameter
Parameter : air te mperature
Air tempera-
ture se nsor X= Temp erature
under engi ne ho od
+/- 5
0C
If further problems arise,
refer to the diagnosing of
that parameter
6.
P
ressure sen-
sor Parameter
: collector
pressure
Parameter : atmospheric
pressure If
further problems arise,
refer to the diagnosing of those parameters
X= Atmo s pheri c
pressure
X= Atmo s pheri c
pressure
7.
COMMAN D OF A CTUATO RS
8. Petrol pump Command:
relay of petrol
pu
mp
F unctioning of
petrol pump must be heard If
further problems arise,
refer to the diagnosing of that command
Command: low speed cool-
i ng ventilator
Command: high speed cool-
i ng ventilator F
unctioning of
l ow speed ventila-
tor must be heard
F unctioning of
high speed venti-
lator mu st be
heard If
further problems arise,
refer to the diagnosing of that command
If further problems arise,
refer to the diagnosing of that command
C
ooling
ventilator
If further problems arise,
refer to the diagnosing
for lack of conformity to
idle mod e adjustment
Pu
t hand under the
engine to feel its
functioning
Command:
idle mode adjust-
me nt engine
St
ep-by-step
engine
If further problems
arise, refer to the diag-
nosi ng defects along the
d raining valve circuit
Va l
ve must be
functional
Command: C
anister draining
valve
C
anister
draining
valve
9.
10. 11. If further problems
arise, refer to the diag-
nosi ng of the states of air
conditioning
Compress
or must
couple
Command:
AC must be op-
erated through the board
switch
Air condi-
tioning (AC)
12.
Command: Water tempe ra-
ture
alert light indicator on
board
Water te m-
perature alert
light indica-
tor
13.
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 52
DIAGNOSING-CON
FORMITY TEST
Pressure circuitParameter: Collector pres-
sure
Parameter: Atmospheric
pressure 290 < X < 370 mbar
X=Atmos
pheric
pressureIf further problems
arise, refer to the
di agnosing of those
p arameters9.
Parameter: Detonation sig-
nal 30 < X < 70
If
further problems
arise, refer to the
di agnosing of that
p arameter
Anti-detonation
circuit
10.
LIST OF STÃTES
LIST OF PARAMETERS
Enrichment
adjustment
Stat
e: enrichme nt adjustment
Parameter: tension of oxygen
probe
Parameter: enrichme nt ad-
justm ent correction Confirmed state
20mV 0 A verage = 128 If
further problems
arise, refer to the
di agnosing of that
state
Stat e: Air-conditioning re-
quirement
Stat e: Accelerated idle mode
Stat e: AC compressor
Parameter: en g i ne ro t ation ratio
Parameter: power absor bed
by AC compressor
State: Ai r-condit ioning requirment
State: Accelerated idle mode
Stat e: AC compressor
Para meter: en gine ro t ation ratio
Para meter: power ab s o rbed by
AC co mp res sor Confi rmed state
Lig ht indicat or is on
when AC co mman ds
co upling of co mpres -
sor
Confi rmed state
Lig ht indicat or is on
when accel erated idle
mo d e is active
Confi rmed state
Lig ht indicat or is on
when injection au tho-
ri zes co u pling of co m-
pressor
75
0 3 00 Not co nfirmed sta te
Confi rmed state
Not co nfirmed sta te
If th e injection does
not auth ori ze co upling
of compres sor
75 0 X<25 0 W
Confi rmed state
Ventilator must have
low rotation ratio
Sta te: Low sp eed ven tilat or
If further problems
arise, refer to the
di agnosing of those
states
11.
12.
Air-conditioning
(board-com-
m
anded AC)
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 59
STATEAIR CONDITIONING AC COMPRESSOR REQUIREMENT
SUGGESTIONSNo defect should be present or memorized
The compressor
clutch do es n ot
couple Check the insulation and continuity along the circuit towards pin 10
injection calculator.
Remedy if necessary.
If
the incident persists, refer to the diagnosing of he air-conditioning.
AFTER REPAIRPerform again the conformity test
CALCULATOR POWER VOLTAGE
PA R AMETER
No defect should be present or memorized.
No consumer should be turned on.
SUGGESTIONS
The contac
t is set
If the voltage < the minimal voltage, then the battery may be flat.
Check the charging circuit, in order to detect the cause of the problem.
If the voltage > the maximal voltage, then it is possible that the
battery may be overcharged.
Check the charging voltage to be correct, with and without consumers.
In idle mode
If the vo ltage < the minimal voltage, then the charging voltage is too
small.
Check the charging circuit, in order to detect the cause of the problem.
If th e voltage > the maximal voltage, then the charge of the battery is
too high.
The vo ltage regulator is faulty.
Remedy this problem, and then check the level of the electrolyte in the
ba ttery.
DIAG NOSING-INTERPRETING THE STATES
vnx.su

19 - 02
FILLING AND DRAINING
The hea ting radiator does not have a tap.
The circula tion of the cooling liquid is done continuosly within the heating radiator, which con-
tributes to the heating of the engine.
F
ILLING
The tightening of the emptying stopper is checked.
Th e dr aining screw placed on the tube between the engine and the air-conditioning radiator is
taken off.
Th e circ uit is filled through the hole of the de-gassing pot.
The dr aining screw is fastened when the liquid flows in a continuous jet.
The engine is set into motion ( 2500 rot/min).
The leve l is adjusted for approx. 4 minutes.
Th e stopper of the de-gassing pot is closed.
D
RAINING
The engine is let to run for 10 minutes at 2500 rot/min until the motor-ventilator starts (i.e. the
time for the automatic de-gassing).
Check if thelevel of the liquid is close to “ Max”.
Do not open the draining screw when the engine is running.
Fasten again the stopper of the de-gassing pot with the engine still hot.
FILLING AND DRAINING19
COOLING - EX HA U ST - FU EL
TANK
vnx.su

19 - 6
19
COOLING - EX HA U ST - FU EL TANK
COOLING FAN REPLACEMENT
for vehicles with air conditioning
1 6 5
3 2 4
7
8
DISMOUNTING
Di
sconnect the (-) plug of the battery.
Di sconnect the cooling fan connector (5).
Di sconnect the cooling fa n resistance connector (1). Mark t he mounting position iden-
tification of the two connectors.
Detach the wiring from clip (6).
Cut the clip attaching the wiring on the cooling fan assembly in point (7).
Dismount the four-attachement screws (3) of the cooling fan on the radiator, recovering the
washers (2) and (4). Remove the cooling fan assembly.
REMOUNTING
Check the condition of the fan propeller, cooling fan electri c motor, washers.
Tighten the attachement screw (3) of the assembly.
Replace the clip from point (7).
Mount the wiring of t he cooling fan assembly taking i nto the considera tion the mount-
ing position m arked before dismounting. This is to be fi xed by means of a clip in point (7)
and will pass trough the clip (6). Connect the cooling fan re sistance connector (1).
Connect the cooling fan c onnector (5). Observe t he m ounting position i dentification of
the two connectors. Connect the battery plug (-). In case the vehicle is equipped with progammable radio-
cassettes, electronic clock, e tc, these a re to be reset before returning the vehicle to t he client. Check t he c ooling fan opera tion: start the vehicle engine and disconnect the water
temperature sensor. The cooling fa n must start. Reconnect the water t emperature sensor,
then by means of the CLIP tester, erase the memorized failure related to the water t em-
perature sensor.
FAILURES
ERASING
vnx.su

19 - 7
19
COOLIN G - EX HA U ST - FU EL TANK
COOLING FAN DIAGNOSTIC
for vehicles with air conditioning
vnx.su