2004 DACIA SUPERNOVA oil temperature

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
SPECIAL TOOL- AND-CHECK SETS
MOT.1202-01 -”CLIC” collar-pincers
MOT.1505 -Device for measuring belt tension
MOT.484 -Device for jacket maintaining -Wrench for angular tightening
-Pincers for elastic collar
TIG H TENING CO UPL E S (daNm )
S crew-nut of stretching runner/pulley 5
Screw of crankshaft pulley 2+68
o+/-6o
Screws of pendular suspension stand 6.2
Screw-nut of hydro-elastic buffer 3.7
Wheel Screws 7.5
Co mbustion-head Screws 2+97
o+/-2o
To take apart :
-the connector of the induction coil;
-the fue l hoses (t he going- and re -
turn circ uit); -the connectors of the injectors;
-the plugs of the sparks;
-the induction coil.
11 - 3
CYLINDER HEA D FITTING
D
IS M O UNT ING
The car is placed on a two-column lift -
ing stand; The battery i s disconnected;
The cooling circuit is emptied at the
jack situated at the lower pa rt of the radia-
tor; The distribution belt is taken apart (see
Chapter Distri bution Belt);
The following are taken apart: -air-filter;
-the c onnector of the c lapper-posi-
tion potentiometer (1); -the acceleration cable;
-the connector of the atmosphe ric
pressure sensor (2);
-the co nnector of the step-by-step
engine (3); -the connector of t he air temperature
sensor (4) on the intake collector;
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 4
PLAC ING OF ELEMENTS
1.Can
ister-draining valve;
2. Air -filter;
3. Det onation sensor (tightening couple: 2.5 daNm);
4. Atmo spheric air-pressure sensor;
5. Step-by -step idle mode-adjustment engine;
6. Cla pper position potentiometer;
7. Air- temperature sensor;
8. Inje ction calcul ator;
9. Shock-s ensor;
10. Fuse-and- relay box;
11. Revolution sensor;
12. Water- temperature sensor;
13. Oxyg en sensor (tightening couple: 4.5 daNm);
14. Igniti on coil;
15. Carbon canister.
1 14 3 5 6 7 4 2 11
9
10
15 13 \
12 8
PLACING OF ELEMENTS
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 17
DEFECTUL
1 Lack of c ommunication with the calculator 17-17
2 Calculator 17-18
3 Supply 17-19
4 Circuit of command actuator re lay 17-20
5 Circuit of command petrol -pump relay 17-21
6 Circuit of 1 cylinder injector 17-22
7 Circuit of 2 cylinder injector 17-23
8 Circuit of 3 cylinder injector 17-24
9 Circuit of 4 cylinder injector 17-25
10 Circuit of 1 and 4 ignition coil 17-26
11 Circuit of 2 and 3 ignition coil 17-27
12 Revolution ratio sensor information 17-28
13 Anti-start device 17-29
14 Failure to memorize the anti-start code 17-29
15 Circuit of atmospheric pre ssure sensor 17-30
16 Circuit of idle mode adjustment 17-31
17 Circuit of clapper potentiometer 17-32
18 Circuit of water-t emperature sensor 17-33
19 Circuit of air-t emperature sensor 17-34
20 Circuit of canister draining valve 17-35
21 Circuit of oxygen probe 17-36
22 Circuit of oxygen probe heating 17-37
23 Circuit of detonation probe 17-38
24 Car speed inform ation 17-39
25 Circuit of command air-c onditioning compressor relay 17-40
26 Water-temperature warning circuit 17-41
27 Circuit of command low-speed ventilator relay (air-c onditioned car) 17-42
28 Circuit of command high-speed ventilator relay (air-conditioned car) 17-43
29 Circuit of command ventilator relay (air-conditioned car) 17-44
30 Functional failure of oxygen probe 17-45
31 Pollutant combustion misfire / Disruptive combustion misfire 17-46
32 Combustion misfire at cylinders 1, 2, 3 and 4 17-47
DIAG NOSING-INTERPRETING THE DEFECTS
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 43
DIAG
NOSING-INTERPRETING THE DEFECTS
LOW SPEED VENTILATOR RELAY COMMAND CIRCUIT
(for A.C. cars)
1. Open circuit or short-circuit to mass of the way to pin 8 of the calcu- lator
2. Short-circuit at 12 V along the way to pin 8 of the calculator.DEFECT
PR ESENT27.
Conditions of breakdown detection by the calculator:
-take the contact and wa it for the dialogue with the tester to be lost
-set the conta ct and enter dialogue.
Condition of performing the diagnosing:
-defec t is present
Note: this defect has to be correlated with the diagnosing of the water
temperature sensor circuit and the air-conditioning installation.
SUGGESTIONS
Check the connection and the condition of the low-speed 700 ventilator connector
Change the connector if necessary.
Check, after setting contact, the presence of +12 V at pole 1 of the 700 relay.
Remedy it if necessary.
Connect the 90-way terminal-tester instead of the calculator and check the insulation
and the co ntinuity along the circuit:
pi n 8 of calculator
♦ po le 2 of the low-speed 700 ventilator relay.
Remedy if necessary.
Check the coil of the low-speed 700 ventilator relay.
Change relay if necessary.
The problem is not yet solved! Consequently, the injection calculator must be changed.
CAUTION! The destruction of the calculator has probably been caused by an electric shock.
The cause of the destruction must be found before mounting a new
calcul ator.
AFTER
REPAIREr ase defects memorized by the computer.
Perform the steps under “Suggestions” to confirm the repair.
Remedy other possible defects.
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 45
DIAG
NOSING-INTERPRETING THE DEFECTS
VENTILATOR RELAY COMMAND CIRCUIT
(for cars having no A.C.)
1. Open circuit or short-circuit to mass of the way to pin 8 of the calculator
2. Sh ort-circuit at 12 V along the way to pin 8 of the calculator.DEFECT
PRESENT29.
Conditions of breakdown detection by the calculator:
-take the contact and wait for the dialogue with the tester to be lost
-set the conta ct and enter dialogue.
Condition of performing the diagnosing:
-the defe ct is present
Note: this defect has to be correlated with the diagnosing of the water
temperature sensor circuit.
SUGGESTIONS
Check the connection and the condition of the connector of the 23 4 cooling ventilator
re lay.
Change the connector if necessary.
Check, af t er se tt i ng co nt a ct, the pr e sence of +12 V at po le 1 of the 234 re lay.
Remedy it if necessary.
Connect the 90 - way te r m in a l -tester instead of th e calculator an d check the in s ulation
and the con ti nui ty alo ng the circui t:
pi n 8 of ca lc ul at or
♦ pole 2 of th e 23 4 cooling ve nt il at or re la y.
Remedy if necessary.
Check th e coil of th e 234 co ol in g ventilator relay.
Change th e relay if ne ce ss ar y .
The problem is not yet solved! Consequently, the injection calculator must be changed.
CAUTION! The destruction of the calculator has probably been caused by an
ele ct ric sho ck.
The cause of the destru ction must be found before mounti ng a new
calcu lato r.
Er ase defects memorized by the computer.
Perform the steps under “Suggestions” to confirm the repair.
Remedy other possible defects.AFTER
R EPAIR
vnx.su

AIR CONDITIONING
62
62 - 1
GENERALITIES
GENERALITIES
The purpose of the a ir conditioning unit i s to produce a decrease of t he temperature in the
passengers compartment a nd to obtain a l ower value t emperature compared to the external
environment one, reducing in the same time the air moisture.
MAINTENANCE
For a vehicle equipped with air conditioning, it is recommended a frequent checking of the
refrigerating agent level. During the year it is recommended:
- the checking of the refrigerant fluid filling;
- the cleaning and the air-blowing of the condenser and the cooling radiator fins;
- the checking of the condensation removal pipe on order not to be clogged.
For important leakage repair, for any components replacement (compressor, condenser, etc)
and if moisture was noticed in t he air conditioning circuit, the dryer filter tank is to be replaced
and the unit draining is to be performed. The same is valid also in case the conditioning circuit
remains open without protection covers more than 10 minutes.
IMP ORTANT
Duri ng winter, it is recommended the frequent start of the system, in order to pro-
long the lifetime of the compressor and of the whole system.
The vehicle equipped with an air conditioning system shall be not exposed for more
than 20 minutes i n painting c abin where there are temperatures higher than 80 °C.
It is obligatory the use of the refrigerating agent and compressor oil type prescribed
by the manufacturer. It is absolutely forbidden to perform welding on the elements of the air condition
circ uits. The filling of the air conditioning system can be pe rformed only by m eans of charging
units and observing the instructions of the manufacturer. For mechanical or body
operations it is recommended pi ping protection in order to avoid their disconnection
by accident. Avoid the drip of the oil compressor on the painted vehicle body.
For component replacement implying the circuit draining, it is absolutely necessary
the use of new parts and of a special oil for compressor.
vnx.su

AIR CONDITIONING
62
62 - 7
The compressor is absorbing the vapors coming from the evaporator at low pressure and
temperature, is compressing them and convey the gas at high temperature and pressure. The refrigerant fluid in high pressure and temperature vapor condition is entering in the second
he at exchanger, which by condensation is transmitting the heat to the external environmental.
At the exit from the condenser, the refrigerant fl uid is in liquid condition, at a high pressure and temperature.
Type of compressor: SD 7Y15
Compressor oil : PAG SP 10 or SP20, volume –135 cmc.
Refrigerant: HFC 134 a, quantity of refrigerant : 0.590 kg
C OMPRESSOR REPLACEMENT
DISMOUNTING
Disconnect the battery.
Drain the refrigerant circuit.
Disconnect the compressor’s connection.
Disconnect the pipes from the compressor.
Dismount the belt tensioning screw and release the belt.
Dismount the compressor attachment screws.
Dismount the compressor.
Replace the compressor.
REMOUNTING
Perform in the reverse order the dismounting operations.
T ension the belt and tighten at the required moment the tightening attachment screw.
Fill the refrigerant circuit and check the good operation of the climate control system.
COMPRESSOR
vnx.su

83
INSTRUMENT PANEL
CONNECTOR C
1. Instrum ent panel lighting
2. Ground
3. Anti starting indicator
4. Supply (+ IC)
5. Free
6. Injection failure indicator
CO NNECTOR D
1. Battery charging circuit failure indicator
2. Fuel minimum level warning
3. Free
4. Free
5. Free
6. Free
7. Free
8. Free
83-2
The corresponden
ce between the positions from A,B,C,D connectors of the instrument panel
and the components of the vehicle electric equipment is the following :
CONNECTOR A
1. Free
2. Rear window defrosting indicator
3. RPM
4. Cooling fluid temperature indicator
5. Oil pressure warning
6. Cooling fluid temperature warning
7. Left turning indicator
8. Left turning indicator
9. Hazard lights indicator
10. Instrument panel ground
CONNECTOR B
1. High beam indicator
2. Free
3. Free
4. Right turning indicator
5. Right turning indicator
6. Supply ()+DC)- after contact
7. Hand brake, braking system failure warning
8. Brake pads wear indicator
9. Free CO
NNECTORS ( until 01.06.2001)
vnx.su