2004 DACIA SOLENZA oil

IGNITION AND INJECTION
17
17 - 86
ALP 3 IDLING PROBLEMS (unstable idling)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
C heck if there is petrol in the fuel tank (fuel indicator failure)
C heck if the vehic le is supplied with adequate fuel
C heck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
C heck the condition of the fuel filter
C heck the condition of the fuel tank
C heck that fuel tank aeration is taking place.
C heck the connection and the condition of the idling regulator connector.
Re place the connector if necessary.
C heck the motor of the idling regulator
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
C heck the spark plugs and ignition coil condition
C heck tha t these eleme nts are specific to that vehicle.
C heck that the exhaust route is not clogged and the catalyst is not clogged.
Check, by means of the oil dipstick, that oil level is not too high.
C heck for lack of sealing at servo-brake (noise).
C heck the intake manifold condition
C heck if the valve body is not clogged
C heck the engine compressions.
C heck the engine flywheel condition
C heck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 87
ALP 4 INTEMP ERATE ACCELERATION OR DECELERATION
(engine unstable running)
RECOMMEND AT IONS Do not consult this diagnostic but before a complete checking by
means of the CLIP tester
Ch eck if air filter is not deformed.
Ch eck if there is petrol in the fuel tank (fuel indicator failure)
Ch eck if the vehic le is supplied with adequate fuel
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the se aling of the exhaust manifold.
Ch eck, by means of the oil dipstick, that oil level is not too high.
Ch eck for lack of sealing at servo-brake (noise).
Ch eck the intake manifold condition
Ch eck if the valve body is not clogged
Ch eck the engine compressions.
Ch eck tha t brake calipers, drums and bearings are not gripped.
Ch eck that tires are inflated
Ch eck the engine flywheel condition
Ch eck tha t cooling system is properly operating
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

19
19 - 6
COOLING - EXHAUST - TANKRadiator
* For the vehicles with air conditioning :
- Connect the t wo pipes to the condenser.
- Connect the engine fan resistance connector (1) and the engine fan connector, then attach
it by clips. Connect the battery.
Attach in clips the oil reservoir for power steering and the air inlet pipe on the battery screen.
Perform the cooling circuit filling and purging.
Perform the air conditioning circuit filling with refrigerant fluid HFC 134a (0.600 Kg) and
check for refrigerant fluid leak ( for vehicles with air conditioning).
vnx.su

19
19 - 7
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles without air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clips the oil reservoir of the power steering from the battery screen.
Disconnect the engine fan connector ( 1) and detach from clips wiring of point ( 2)
Dismount the four attachment screws ( 3) of the engine fan on radiator.
Carefully dismount the engine fan assembly from guiding points (4).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully position the engine fan assembly in the guiding points (4).
Mount the attachment screws ( 3) of the assembly on the radiator.
Connect the engine fan connector ( 1).
Attach in clips the wiring in point ( 2).
Attach in clips the power steering oil reservoir on the battery screen.
Mount the air inlet pipe.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, e lectronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client.
Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

19
19 - 9
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles with air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clip the power steering oil reservoir from the battery screen.
Disconnect the engine fan connector ( 1)
Detach wiring from clips ( 2) and (3).
Disconnect the connector of the cooling engine fan resistance (4).
Carefully dismount the engine fan assembly from the radiator, from sustaining points (5).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully mount the engine fan assembly in the sustaining points (5).
Connect the connector of the engine fan resistance ( 4).
Connect the cooling engine fan connector ( 1) and attach it in clip (3) then in clip (2).
Attach in clips the power steering oil reservoir on the battery screen. Mount the air inlet
pipe.
Connect the battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, electronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client. Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

20
CLUTCH
20 - 3
Diagnostic
EFFECT OF TREPIDATION
Check for oil leaks at the clutch
casing level.
If there are no leaks.
Check the tightening and the
c ondi t i on of t he ge arbox a nd e ngi ne
supports (fix it if necessary).
If the incident is persisting.
Che c k t he c l utch c ont rol (fi x it if
necessary).
If the incident is persisting.
Check the idle regime (unstable or
incorrect).
Fix it if necessary.
If the incident is persisting.
Replace the clutch. F
ix the oil leak and replace the c lutch
disk if necessary.
vnx.su

CLUTCH
20
20 - 4
Diagnostic
NOISE AT FREE CLUTCH
(oppressive and regular noise subject to engine regime)
Check for oil leaks at clutch casing
level.
If there are no leaks.
Check the tightening and condition
of the gearbox and engine supports
( fix it if ne cessary).
If the incident is persisting.
Check the engine running at idling
(unstable or i ncorrect).
Fix it if necessary. If the incident is persisting
Fi x t he oi l lea k and re pl a c e t he
clutch disk if necessary.
Replace the clutch.
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 3
Tightening moments in daNm
TIGHTENING MOMENTS (daNm)
A ttachment screws of the mechanism crankcase on the
clutch – differential case 2.5
S econdary shaft screw 7
Primary shaft nut 19
Back cap fixing screws 2.5
Oil draining plug 2.5
R everse driving contact 2.5
S crews for fixing the bellows assembly – left transmission cap assembly 2.5
Screws for fixing gearbox on engine case (M10 – 90) 4.4
Screws for fixing gearbox on engine case (M10 – 35) 2.1
Nuts for fixing gearbox on engine 4.4
LOCTOU blocking element fixing screw 0.5
S crews for fixing RPM sensor on the clutch case 0.8
S crews for fixing the control axle assembly 2
S crews for fixing clutch cable support 4.8
vnx.su