ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 37
ROCKERS ADJUSTMENT
Adjustment to be performed only with cold engine.
The adjustment values are:
- admission 0.10 mm
- exhaust 0.25 mm
1. Camshaft gear without marks.
a) Method called “ in balance”
Cylinders valves in balance
(exhaust end, admission beginning)
1
3
4
2 Adjust cylinder rocker
4
2
1
3
b) Method called “ exhaust valve maximum opened”
Rotate the engine (clockwise, as seen from distribution) until the exhaust valve of the cylinder
1 is reaching to the maximum opening and then adjust the clearance at the admission valve of the
cylinder 3 and the valve clearance of the cylinder 4. Proceed in the same way also for the others cylinders as per next table:
Exhaust valve
Maximum opened
1
3
4
2Admission valve to be
adjusted
3
4
2
1 Exhaust valve to be
adjusted
4
2
1
3
Dismounting – Remounting
vnx.su
ENGINE E7J-26216
16 - 6
ALTERNATOR – STARTER
ENGINE STARTER
E7 J - 262 D 907 - M00 2T 13581
IDENTIFICATION
DIAGNOSTIC
Special tool : CLIP tester – TECHNIC for measuring the battery voltage and the absorbed
intensity in the starting stage.
OPERATION ABNORMALITIES THAT MIGHT BE NOTICED
- Battery failure = large voltage drop on starter during engine starting stage.
- Blocked starter = the absorbed current is very high.
- Solenoid failure = the absorbed current is very low.
In order to perform the measurements, it is necessary the engine drive by means of the starter,
but stopping the engine starting.
To do that, disconnect the RPM sensor (located on clutch casing).
REMARK:
After performing this checking, erase by means of the CLIP tester, the possible failures
memorized by the computer.
St arter
vnx.su
IGNITION AND INJECTION
17
17 - 20
DIAGNOSTIC CONDI T IONS
If wh en setting on the contact, with stopped engine, one of the following conditions is accom-
plished: -air temperature, red by the air temperature sensor, is not situated between –6° and 119°C.
-w ater temperature, red by the water temperature sensor, is not situated between –6° and
119°C.
-atmosphe ric pressure is under 775mbar,
then the OBD diagnostics are not authorized until the next contact setting on. In order to have a correct operation of the OBD diagnostic system, no electric failure of the
injection system must exist, even if the lighting of the OBD indicator is not established. The catalyst and oxygen sensor diagnostics can not be performed in the same time, but one
after other.
When the catalyst or oxygen sensor diagnostics are under operation, the canister purging valve
is closed, and the adaptive values are “blocked” at the last existent value prior to a.m. diagnostics
starting. TESTS PERFORMING LOGIC
-Solve fa ilures of electric nature.
-Erase a ll failures by means of the CLIP tester
-Perform the “teaching” stage of all adaptive values by the injection system (if necessary).
OB D COMPLETE ACTIVATION BY MEANS OF CLIP TESTER
-Erase all memorized failures.
-Erase the “learned” values from UCE injection if further to an intervention on an injection
system component, a disturbance of the “learned” values took place (step-by-step engine, flywheel
or RPM sensor, etc).
RETENTIONS (“LEARNINGS”) NECESSARY FOR UCEINJECT ION FOR OBD DI AGNOSTIC
〈 COUPLING/SUPPLY RATE LEARNING (state “ET014 = cylinder recognition 1” is PER-
FORMED with running engine). This is to be performed as following:
-a deceleration with “cutting” of the petrol injection in the third gear of the gearbox, be-
tween 3000-3500 rot/min for at least 2 seconds,
-a second deceleration with ”cutting” of the petrol injection in the third gear of the gearbox,
between 2400-2000 rot/min, for at least 2 seconds.
〈 MIXTURE ENRI CHING ADAPTIVE LEARNING
In order to do that, it is necessary that vehicle is running observing in the same time the pressure
ranges men tioned in the chapter “ Enriching adaptive correction”.
〈 State “ET202 = OBD diagnostic of combustion misfires taken into consideration” must be
AC TIVE.
“On Board Diagnostic” diagnostic conditions
vnx.su
IGNITION AND INJECTION
17
17 - 29
AFTER
REPARATION P
erform the operations from “recommendations” for reparation confirmation.
Fix a ny other possible failures.
Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.
C heck the c onnection and the state of the de tonation sensor connector.
R eplace the sensor ’s connector if necessary.
C heck the tightening of the RPM sensor on the engine block
Fi x if necessary.
C onnect the 90 w ays terminal box instead of the injection c omputer then c heck the insulation,
continuity and absence of the parasite resistance on lines:
Pin 20 injection computer > p in 1 detonation sensor
Pin 79 injection computer > p in 2 detonation sensor
Pin 19 injection computer > RPM sensor sc reening
Fix if necessary
If the problem is persisting after these checking, fix the other failures the n perform the conformity
checking.
RE CO MMENDATIONS
Conditions for diagnostic application for memorized failure:
Perform a road test with warm and in charge engine.
* If the failure is memorized with OBD indicator on, check in the context part,
if state “ET289 : Detonation sensor cir cuit” corresponding to the OBD
i ndicator lighting request is affirmative. In this case , proceed as per bellow
m entioned method.
Diagnostic – Failures interpretation
DF006
P RESENT
OR
ME MO RIZEDDETONATION SENSOR CIRCUIT
1. DEF : Open circuit or short-circuit
vnx.su
IGNITION AND INJECTION
17
17 - 85
ALP 2 STARTING PROBLEMS engine is not starting or is difficulty starting)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
Ch eck that starter is well operating
Ch eck there is petrol in the fuel tank (fuel indicator failure).
Ensure that vehic le is supplied with adequate fuel.
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Ch eck the electric supply of the fuel pump.
Ch eck the good operation of the choke sensor.
Ch eck the motor of the idling regula tor.
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the engine compressions
Ch eck the flywheel condition
Ch eck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su
IGNITION AND INJECTION
17
17 - 86
ALP 3 IDLING PROBLEMS (unstable idling)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
C heck if there is petrol in the fuel tank (fuel indicator failure)
C heck if the vehic le is supplied with adequate fuel
C heck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
C heck the condition of the fuel filter
C heck the condition of the fuel tank
C heck that fuel tank aeration is taking place.
C heck the connection and the condition of the idling regulator connector.
Re place the connector if necessary.
C heck the motor of the idling regulator
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
C heck the spark plugs and ignition coil condition
C heck tha t these eleme nts are specific to that vehicle.
C heck that the exhaust route is not clogged and the catalyst is not clogged.
Check, by means of the oil dipstick, that oil level is not too high.
C heck for lack of sealing at servo-brake (noise).
C heck the intake manifold condition
C heck if the valve body is not clogged
C heck the engine compressions.
C heck the engine flywheel condition
C heck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su
19
19 - 7
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles without air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clips the oil reservoir of the power steering from the battery screen.
Disconnect the engine fan connector ( 1) and detach from clips wiring of point ( 2)
Dismount the four attachment screws ( 3) of the engine fan on radiator.
Carefully dismount the engine fan assembly from guiding points (4).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully position the engine fan assembly in the guiding points (4).
Mount the attachment screws ( 3) of the assembly on the radiator.
Connect the engine fan connector ( 1).
Attach in clips the wiring in point ( 2).
Attach in clips the power steering oil reservoir on the battery screen.
Mount the air inlet pipe.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, e lectronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client.
Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su
19
19 - 9
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles with air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clip the power steering oil reservoir from the battery screen.
Disconnect the engine fan connector ( 1)
Detach wiring from clips ( 2) and (3).
Disconnect the connector of the cooling engine fan resistance (4).
Carefully dismount the engine fan assembly from the radiator, from sustaining points (5).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully mount the engine fan assembly in the sustaining points (5).
Connect the connector of the engine fan resistance ( 4).
Connect the cooling engine fan connector ( 1) and attach it in clip (3) then in clip (2).
Attach in clips the power steering oil reservoir on the battery screen. Mount the air inlet
pipe.
Connect the battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, electronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client. Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su