2004 DACIA SOLENZA air condition

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 26
Diag nostic
FAILURES LOCATING BASED ON CLIENT CLAIM
(algorithm for damage locating)
A LP1. MISSING COMMUNICATION CLIP TESTER / E.C.U DECODER
RECOMMENDATION Check if the lines K a nd L are not perturbed by another computer
of the vehicle.
Check the condition of the F03, F04 fuses from cockpit fuse box.
Be sure the CLIP t ester is not the cause of t he failure, by trying the communication with
another computer of the vehicle.
Check the tension of the battery (U>12,3V). If it is necessary, charge the battery.
Check the correct c onnection of the E.C.U. decoder to the wiring.
Check the supply of the E.C.U. decoder : - mass at pin A8; - supply (+IC) at pin A9.
Be sure that the diagnostic socket is correctly supplied.
Check the continuity and the isolation of the electric wiring on the pins’ line corresponding to:
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the dialogue CLIP tester – E.C.U. decoder cannot be established, then replace the decoder.
When the communication with the tester is established, solve the
AFTER REPAIRING failures displayed by CLIP.
Perform a conformity checking.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 29
Diag nostic
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
( even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHED
OFF
RECOMMENDATION Check if the “Procedure E.C.U. decoder replacement” was correctly performed
Check the fuse F03 condition from the cockpit
fuse box.
Is the fuse good?
Is there the failure “DOORS BLOCKING
CONTACT”.
Check the continuity and the isolation related
to the mass, between the pin A 5 of the E.C.U.
decoder and the dashboard.(pin 6 from black
connector)
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
damaged element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder a nd check if t he indicator switches
off;
- if the anti starting system is turned off, connect
the pin A5 of t he wiring connector from the
E.C.U. decoder to an electric mass and check
if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
No
No
Yes
Y e s
No
Yes
Yes
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 32
Diag nostic
ALP6. BLOCKING/UNLOCKING DOORS NOT OPERATING
RECOMMENDATION Check with the CLIP tester the absence of the failures.
If there are memorised failures, these must be removed.
Are the doors blocking mechanisms correctly
operating ?Repair the damaged mechanisms.No
Check the continuity and the isolation related to the
mass of the wiring between :
E.C.U . decoder pin B8 actuators
Pin B9 doors
Is the wiring in good condition?
Fix the wiring.No
Check the continuity and the isolation
related to the mass of the wiring between
E.C.U . pin B2 1 switch
decoder Pin B5 5 blocking doors
Is the wiring in good condition?
Repair.
Di sconnect the E.C.U. decoder, then supply
the wiring c onnector with +12 V at pin B9
and the mass at the pi n B8, than versa (+ 12
V at pin B8 and t he mass at pi n B9).
Ar e the actuators bl ocking/unlocking the
doors?
Damaged actuators.
Replace them.
Replace the E.C.U. decoder, t hen perform the “E.C.U. decoder
replacement procedure”. No
Yes
Yes
No
YesYes
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 33
Diag nostic
ALP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D be c om ing
A CTIVE when t he RF remote c ontrol is
activated?S ee the treatment of the states 11G
and 11D cf. chapter “Diagnostic”.No
Check the fuse F03 condition from the cockpit
fuse box.
Is it good?
Replace the fuse.No
Ye s
Yes
See the treatment of the failure
“Doors blocking contact” and the state 14 G cf. chapter
“Diagnostic”.
See ALP6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Activate the doors’ locking switch from the
dashboard.
Are the doors blocking/ unlocking ?
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 34
Diag nostic
ALP 8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester. If there are failures, fix them first.
Check if the synchronisation of the RF remote control and the E.C.U. decoder has been
performed.
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation
related to t he mass and the +12 V of the
electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalling system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F02 condition from the cockpit
fuse box.
Is it good?Replace the fuse.
Di sconnect the FLASH relay. Supply with
+12, the pole 4 of the relay. Are the left turning
lights turning on? Supply with +12 V the pole
5 of the signal relay. Are the right/left turning
lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 53
AFTER REPAIRINGRemediaπi celelalte eventuale defecπiu ni .
ªtergeπi defectele memorat
e.
RECOMMENDATIONSApplying conditions of the diagnostic to the memorized failure :
- failure declared present when setting the contact on (+After contact).
Diagnostic – Failures interpretation
DF055
PRESENT
OR
ME MO RIZED
CODED LINE CIRCUIT
Check the connection and condition of the connector with 40 pins EH1 of the Cockpit Central Unit.
If necessary, repair the connector.
Check the continuity and insulation of the connection:
Connector EIII with 40 pi ns Cockpit central Unit pin B36 i njection computer
(see the corresponding engine electric diagram)
If necessary, fix it.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 54
RECOMMENDATIONS Applying conditions of the diagnostic to the memorized failure:

- fa ilure declared present when setting the contact on (+After contact).
Diagnostic – Failures interpretation
DF 069
PRESENT OR
MEMORIZED UCH CONNECTION ANTI-STARTING BUSHING
CC.O: short-circuit at m ass
CC.1: short-circ uit a t 12 V
CC.0Check the condition and connection f the anti-starting bushing
If necessary, repair the connector.
Check the connection and condition of the connector with 40 pins
EH1 of the Cockpit Central Unit
Repair the connector if necessary.
Disconnect the bushing connector and check the correct supply of
+ 12V at pin 3 bushing connector
Fix it if necessary.
Check the continuity and insulation of the connection between:
Cockpit fuse box F04 (15A) pin 3 bushing
Fix it if necessary.
CC.1Check the connection and condition of the bushing connector.
Fix the connector condition if necessary.
Check the connection and condition of connector 40 pins EH1 of
Cockpit Central Unit.
Fix the connector if necessary.
Check the continuity of the connections between:
mass pin 2 bushing
Connector 40 pi ns EH1 of UCH pin A16 pin 4 bushing
Fix if necessary.
AFTER REPAIRING Apply the recommendation Fix all others failures
Erase the memorized failures.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 61
ET167
ANTI – STARTING INDICATOR
Diagnostic – States interpretation
RECOMMENDATIONS The state <> must pass at NO after setting
the contact on.
The state << active anti-starting>> must become “YES”
after 10 seconds from contact setting off.
Check the connection and condition of the instrument panel connector.
Fix it if necessary.
Check the connection and condition of the connector with 40 pins EH1 of Cockpit Central Unit.
Fix it if necessary.
Check the continuity and insulation of the connection:
Pin A32 connector EH1 with 40 pins of UCH pin 6 black connector instrument panel.
Fix, if necessary.
Perform again a system diagnostic
Fix all others failures
Erase the memorized failures.
AFTER REPAIRING
vnx.su