2003 SSANGYONG MUSSO engine

1B1-36 M162 ENGINE MECHANICAL
4. Remove the three flange bolts in the exhaust camshaftsprocket. Installation Notice
5. Separate the chain from the camshaft sprockrt. Notice Be careful not to drop the chain into the timing case.
Do not reuse the removed bolts.
Tools Required
000 589 01 10 00 Box Wrench Insert
116 589 02 34 00 Screw-fixed Pin
116 589 20 33 00 Sliding Hammer Removal & Installation Procedure
1. Rotate the crankshaft so that the piston of number 1 cylinder
is at TDC. Notice Rotate the crankshaft in the normal engine direction.
2. Put the alignment marks (arrows) on the timing chain and camshaft sprocket.
3. Drain the coolant from the crankcase.
Tightening Torque 1st step 18 - 22 Nm
2nd step 90
° ± 5 °

M162 ENGINE MECHANICAL 1B1-37
7. Remove the cylinder head bolts in numerical order.Installation Notice
8. Check the length of the cylinder head bolt. Installation Notice Box Wrench Insert 000 589 01 10 00
Replace the bolt if the measured length exceed the max. length.
Apply the oil to the thread surface of bolt.
9. Carefully remove the cylinder head and check the mating surface.
10. Installation should follow the removal procedure in the reverse order.
6. Remove the guide rail fixing pin from the cylinder head using
the sliding hammer (01) and the threaded pin (02).
Sliding Hammer 116 589 20 33 00Threaded Pin 116 589 02 34 00
Tightening Torque 1st step 55 Nm
2nd step 9 0
°
3rd step 9 0 °
Length (L)New 160 ± 0.8 mm
Max. 162 ± 0.7 mm

1B1-38 M162 ENGINE MECHANICAL
TIMING GEAR CASE COVER Preceding Work : Removal of cylinder head front coverRemoval of alternator bracket
Removal of tensioning device
Removal of belt pulley and vibration damper
1 Bolt (M8 x 60, 3 pieces) .................22.5-27.5 Nm
2 A/C Bracket
3 Bolt (M8 x 65, 3 pieces) .................22.5-27.5 Nm
4 Bolt (M8 x 40, 1 piece) ...................22.5-27.5 Nm
5 Bolt (M8 x 60, 1 piece) ...................22.5-27.5 Nm 6 Seal
7 Timing Gear Case Cover
8 Roll Pin
9 Bolt (M6 x 22, 6 pieces)
......................... 9-11 Nm
Removal & Installation Procedure
1. Put the alignment marks (arrows) on the timing chain and camshaft sprocket.
2. Unscrew the A/C bracket bolts (1) and remove the bracket.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE MECHANICAL 1B1-39
3. Remove the cooling fan and the viscous clutch. Unscrewthe three bolts from the cooling fan bracket and remove the bracket (arrows). Installation Notice
4. Remove the timing gear case cover after unscrewing the bolts (3) and (4) from the timing gear case cover and the bolt (9) from the oil pan. Notice Be careful not to damage the oil pan gasket.Installation Notice
Apply the sealant after cleaning the timing gear case
cover surface.
Be careful not to stain the oil chamber of chain tensioner
with the sealant.
5. Installation should follow the removal procedure in the reverse order.
6. Warm up the engine and check for oil leaks.
Tightening Torque 22.5 - 27.5 Nm
Tightening Torque Bolt (3,4) 22.5 - 27.5 Nm
Bolt (9) 9 - 11 Nm

1B1-40 M162 ENGINE MECHANICAL
CRANKSHAFT SEALING REAR COVER Preceding Work : Removal of the automatic transmission drive plate
1 Bolt (M6 x 20, 6 pieces)......................... 9-11 Nm
2 Radial Shaft Seal
3 Rear Cover 4 Sleeve
5 Bolt (M6 x 85, 2 pieces)
......................... 9-11 Nm
6 Washer

M162 ENGINE MECHANICAL 1B1-41
Tools Required
601 589 03 43 00 Sleeve Removal & Installation Procedure
1. Unscrew the bolts (1) and (5) and remove the closing coverby pulling the rear cover lug (arrows). Notice Be careful not to damage the oil pan gasket.
2. Clean the sealing surface of the crankcase and the rear sealing cover.
3. Check the radial shaft seal and replace it if necessary.
4. Apply the Loctite 573 to the rear cover sealing surface.
5. Apply the engine oil to the dust lip of the radial shaft seal.
NoticeDo not use the grease.
6. Using the special tool, press the radial shaft seal and the rear cover.
7. Tighten the rear cover bolt (1) and then tighten the oil pan bolt (5) as specified and remove the special tool. Installation Notice
Seal Assembler 601 589 03 43 00
Tightening Torque(Bolt 1,5) 9 - 11 Nm

1B1-42 M162 ENGINE MECHANICAL1 Center Bolt (M18 x 50) ......1st step 200- 220 Nm
2nd step 90 °+10 °
2 Vibration Damper Disk
3 Bolt (M6 x 20, 6 pieces) .....................7.7-9.5 Nm
BELT PULLEY AND VIBRATION DAMPER Preceding Work : Removal of cooling fan and viscous clutch
Removal of fan shroud Removal of drive belt
4 Vibration Damper Assembly
5 Woodruff Key
6 Bolt (M6 x 12, 4 pieces) ......................... 9-11 Nm
7 Cooling Fan Pulley

M162 ENGINE MECHANICAL 1B1-43
Components
1 Center Bolt (M18 x 50)
2 Center Bolt Washer
3 Vibration Damper and Pulley Assembly
4 Key
5 Crankshaft Front Seal
6 Timing Gear Case Cover
7 Crankshaft Sprocket (Camshaft Driven)
8 Crankshaft Sprocket (Oil pump Driven)
9 Crankshaft
10 Oil Pan 11 Oil Pan Gasket
12 Oil Pan Mounting Bolt (M6 x 22)
Service Data Standard
Permissble Deviation of The Vibration Damper Radial Runout
Axial Runout0.6 mm 0.6 mm
Tools Required
103 589 00 33 00 Puller
001 589 65 09 00 Socket Wrench Insert
602 589 00 40 00 Engine Lock Removal & Installation Procedure
1. Adjust the piston of number 1 cylinder to the TDC.