2003 SSANGYONG MUSSO engine

1B1-20 M162 ENGINE MECHANICAL Removal & Installation Procedure
1. Remove the belt pulley.Installation Notice
2. Disconnect the hydraulic pipe of the power steering pump and drain the oil.
3. Unscrew the bolts (arrows) and remove the steering pump. Installation Notice
Notice Pull the tensioning pulley clockwise as shown in the figure.
4. Remove the compressor after disconnecting the wiring connector and refrigerant pipe of A/C compressor. Notice Discharge all the refrigerant before removing the pipes.
Tightening Torque 40.5 - 49.5 Nm
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE MECHANICAL 1B1-21
5. Disconnect the vent hose from the A/C bracket.
6. Unscrew all the mounting bolts (arrows) and remove theA/C bracket and the gasket. Installation Notice
7. Clean the sealing surface.
8. Replace the gasket with new one.
9. Installation should follow the removal procedure in the reverse order.
10. Check the oil leakage by operating the engine after installation.
Tightening Torque 22.5 - 27.5 Nm

1B1-22 M162 ENGINE MECHANICAL
HYDRAULIC ENGINE MOUNTING INSULATOR Service Data

M162 ENGINE MECHANICAL 1B1-23
Sectional View
1 Rubber Body
2 Brackek
3 Core
4 Lower Bolt
5 Rubber Plunger
6 Plunger Plate
7 Rubber
8 Plate9 Lower Orifice
10 Upper Orifice 11 Diaphram
12 Cover Plate
13 Upper Bolt
14 Flange Bolt
15 Rivet
16 Fluid

1B1-24 M162 ENGINE MECHANICAL
1 Upper Nut
2 Hydraulic Installor.................62-93 Nm
3 Lower Nut ............................. 28-47 Nm
Removal and Installation Procedure
1. Unscrew the upper nut(1) on engine mounting and remove the engine. Installation Notice
3. Installation should follow the removal procedure in the reverse order.
Tightening Torque 62 - 93 Nm
2. Unscrew the lower nut(3) and remove the hydraulic engine mounting insulator. Installation Notice
Tightening Torque 28 - 47 Nm
Notice If the insulator is spotted with oil, replace the hydraulic
insulator assembly.

M162 ENGINE MECHANICAL 1B1-25
POLY V - BELT Preceding Work : Removal of cooling fan
1 Poly V-belt
Removal & Installation Procedure
1. Release the belt tension by turning the belt tensioning pulley nut clockwise.
2. Remove the poly v-belt.
Notice Check the belt for damage and tensioning pulley bearing
point for wear and replace them if necessary.
3. Install the belt by turning the nut of tensioning pulley clockwise.2 Belt Tensioning Pulley

1B1-26 M162 ENGINE MECHANICAL Poly V-Belt Arrangement
1 Belt Tensioning Pulley
2 Crankshaft Belt Pulley
3 A/C Compressor Pulley
4 Cooling Fan Pulley5 Alternator Pulley
6 Idler
7 Power Steering Pump Pulley
8 Cooling Fan and Water Pump Pulley

M162 ENGINE MECHANICAL 1B1-27
TENSIONING DEVICE Preceding Work : Removal of poly v-belt
1 Belt (L = 2245)
2 Bolt Combi(M8 x 14, 3 pieces) + Washer....................................................... 22.5-27.5Nm
Removal & Installation Procedure
1. Remove the poly v-belt.
2. Remove the tensioning pulley by turning its mounting nut counter clockwise as shown in figure. Installation Notice 3 Water Pump Pulley
4 Nut
5 Tensioning Pulley
Tightening Torque 40.5 - 49.5 Nm