2003 SSANGYONG MUSSO check oil

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.Installation Notice
5. Loosen the radiator upper mounting bolt and remove the mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and replace it if necessany.
8. Installation should follow the removal procedure in the reverse order.
Tightening Torque Hose : 29 - 40Nm

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove thewiring connectors (1 and 15) from ignition coil and measure the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1) between ECU terminal No. 71 and No. 69.
Notice If out of specified value, replace the ignition coil.
Specified Value
0.9 - 1.6 (20 °C)
Specified Value 200 - 350 V
Notice
Measure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
If out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance between 5a and 5b.
Specified Value 6 - 8.5 k

M161 ENGINE ELECTRICAL 1E2-11
Inspection & Maintenance (for E2.3 MSE)
1. Measure the primary resistance between the cable terminals1 and 15 after removing the ignition cable wiring connector
(1 and 15) with ignition switch OFF. Notice Replace the ignition coil if out of the specified resistance.
T1/2 : between No.71 and No.69
Notice Check the ignition cable and the ECU if out of the
specified value.
3. Measure the secondary cable resistance between the ignition coil 5a and 5b using a multimeter.
2. Measure the primary voltage(T1/1) between the ECU
terminals No.72 and No.69 during the engine cranking (starter motor activated).
Specified Value 6 - 8.5 K
Specified Value0.9 - 1.6
Specified Value 200 - 350 V

M162 ENGINE CONTROLS 1F1-21
Failurecode ItemChecking method
 Ignition:ON
Test stepRequirementSpecified
value Possible cause
10 12 11 - 14V



ECU:power
supply - terminal 30(TM.30)
2.2 


Power
supply:
- terminal 87(TM.87) 
Ignition:ON 
Power supply cable
 OVPR
IGNITION SYSTEM TEST
08, 
1.1
 1.2
1.1 
Ignition:ON
10 2 11 - 14V



Ground
cable:- Battery ground
 Ground cable
 Ground condition
(figure 1)
Diagnosis
socket
69 2
Diagnosis socket
1.2 
Ignition:ON
11 2 11 - 14V



Power
supply: - terminal 30(TM.30)
 Power supply cable
 Fuse No.8
Diagnosis socket
2.0 
Ignition:ON
51 1 11 -14V



ECU:power
supply - terminal 87(TM.87)
08, 
2.1
 2.2
2.1 
Ignition:ON 11 - 14V



Ground
cable - Electronic ground 
Ground cable
52
Diagnosis socket
11 1
Diagnosis
socket
 Ignition:OFF
11 - 14V
< 1V
3.0 
Ignition:ON
69 71 11 - 14 V



Ignition
coil(T1/1) - No.2,5 Cylinder64, 
Cable
 Ignition coil(T1/1)
 Fuse No.17
 Engine:in cranking > 10 V

1F1-22 M162 ENGINE CONTROLS
Failurecode ItemChecking method
Te s t
stepRequirementSpecified value Possible cause

6.1 


Crankshaft
position sensor:- Resistance 
Ignition:OFF
- Disconnect the coupling "NO.2"from ECU 
Cable
 Crankshaft position
sensor

6.0 
Engine:in cranking
99 100 Measure the
signal (refer to figure 6)



Crankshaft
positionsensor:- Signal
17, 18,20,67, 
6.1
 Increament failure in
driven plate
> 5 V -
99 100
99 100
1050 - 1400

7.0 
Engine:in cranking
104 106 
7.1
 Cable
 Camshaft position
sensor
Measure the
signal(refer to figure 7)



Camshaft
position sensor:- Signal
4.0 
Ignition:ON
69 72 11 -14 V



Ignition
coil(T1/2) - No.3,4 Cylinder65, 
Cable
 Ignition coil(T1/2)
 Fuse No.17
 Engine:in cranking > 10 V

Engine:in idling
- Voltage (alternating) 
Engine:in cranking
 Engine: in idling > 2.5 V -
19, 58,

5.0 
Ignition:ON
69 70 11 -14 V



Ignition
coil(T1/3) - No.1,6 Cylinder66, 
Cable
 Ignition coil(T1/3)
 Fuse No.17
 Engine:in cranking > 10 V
17, 18,20,67, Voltage value
is increased
when engine rpm is
increased

M162 ENGINE CONTROLS 1F1-23
Failurecode ItemChecking method
Te s t stepRequirementSpecified
value Possible cause
106 11 The value will
be changed in 1.2 - 1.7 V
- Voltage
(alternating)
0.9 - 1.6
71 11
71 72

Engine:in cranking
7.1 
Ignition:ON
- Remove the connector from the Camshaft positionsensor betweenNo.1 terminal andNo.3 terminal.
13
11 -14 V



Camshaft
positionsensor(E23 only)- Power supply
 Cable
 OVPR



Ignition
coil(T1/1) - primary coil voltage(No.2 and 5 cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 %(using engine tester)
 Ignition:OFF 200 - 350 VCamshaft position
sensor
64, 8.0
8.1
8.1 


Connecting
resistance of ignition coilbetween T1/1 and T1/2 
Cable
 Ignition coil T1/1
 Ignition coil T1/2
72 11



Ignition
coil(T1/2) - primary coil voltage(No.3 and 4cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 %(using engine tester) 200 - 350 V
65, 9.0
9.1
0.9 - 1.6
72 71
 Ignition:OFF 9.1 


Connecting
resistance of ignition coilbetween T1/2 and T1/1 
Cable
 Ignition coil T1/1
 Ignition coil T1/2
The
resistance of
ignition coil at 20°C is
approached 0.6
The
resistance of
ignition coil at 20°C is
approached 0.6

1F1-24 M162 ENGINE CONTROLS
Failurecode ItemChecking method
Test
stepRequirementSpecified
value Possible cause
8 - 20 KV



Ignition coil
(T1/1, T1/2, T1/3)
- Secondary ignition voltage
> 10 M
117 118
 Engine:in cranking - Select the ignition
coil in order of T1/1,T1/2
- Measuring range: 20KV
- Time range:100 %
 Ignition:OFF
- Disconnect the coupling "No.2" fromECU.
12.0 


Knock
sensor 1 - Resistance (cylinder No1, 2, 3) 
Connecting
condition
 Cable
 ECU

11.0
64,65,66, Engine tester

11.1
 Ignition plug
 ECU
 High tension cable
6 - 8.5 K



Ignition coil
(T1/1, T1/2, T1/3)
- Secondary coilresistance 
Remove the high
tension cable of T1/1, T1/2, T1/3.

11.1 Ignition coil
(T1/1, T1/2, T1/3) 
Ignition coil T1/1
 Ignition coil T1/2
 Ignition coil T1/3
TM.4a TM.4b
56,
11



Ignition
coil(T1/3) - primary coil voltage(No.1 and 6cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 % 200 - 350 V
66, 10.0
10.1
0.9 - 1.6
70 72
 Ignition:OFF 10.1 


Connecting
resistance of ignition coilbetween T1/3 and T1/2 
Cable
 Ignition coil T1/3
 Ignition coil T1/2
> 10 M
114 115 Ignition:OFF
- Disconnect the coupling "No.2" from ECU. 13.0 


Knock
sensor 2 - Resistance (cylinder No.4, 5, 6) 
Connecting
condition
 Cable
 ECU
57,
The
resistance of
ignition coil at 20°C is
approached 0.6

M162 ENGINE CONTROLS 1F1-47
3. Disconnect the vacuum hose.
4. Disconnect the circlip and remove the fuel pressureregulator.
5. Apply the oil to O-ring lightly and then replace it.
6. Installation should follow the removal procedure in the reverse order.
7. Check for fuel pressure and internal leaks by operating the engine.
2. Discharge the pressure in fuel supply system by pressing
the service valve.
Removal & Installation Procedure
1. Remove the fuel pressure test connector.