2003 NISSAN TEANA wiring diagram

TROUBLE DIAGNOSIS
LAN-77
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of unified meter and A/C amp.
2. Check the resistance between the unified meter and A/C amp. harness connector terminals.
OK or NG
OK >> GO TO 3.
NG >> Repair the unified meter and A/C amp. branch line.
3. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the unified meter and A/C amp. Refer to DI-28, "
Schematic" .
OK or NG
OK >>
Present error: Replace the unified meter and A/C amp. Refer to DI-34, "Removal and Installa-
tion of Unified Meter and A/C Amp." .

Past error: Error was detected in the unified meter and A/C amp. branch line.
NG >> Repair the power supply and the ground circuit.
Steering Angle Sensor Branch Line CircuitBKS002ED
INSPECTION PROCEDURE
1. CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection
(unit side and connector side).
OK or NG
OK >> GO TO 2.
NG >> Repair the terminal and connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of steering angle sensor.
2. Check the resistance between the steering angle sensor harness connector terminals.
OK or NG
OK >> GO TO 3.
NG >> Repair the steering angle sensor branch line.
3. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the steering angle sensor. Refer to BRC-48, "
Schematic"
(Models with VDC), LT- 7 9 , "Wiring Diagram — AFS —" (Models with AFS).
OK or NG
OK >>
Present error: Replace the steering angle sensor. Refer to BRC-91, "Removal and Installation"
(Models with VDC), LT- 9 4 , "REMOVAL" (Models with AFS).

Past error: Error was detected in the steering angle sensor branch line.
NG >> Repair the power supply and the ground circuit.
Unified meter and A/C amp. harness connector
Resistance (Ω)
Connector No. Terminal No.
M41 1 11 Approx. 54 – 66
Steering angle sensor harness connector
Resistance (Ω)
Connector No. Terminal No.
M26 4 5 Approx. 54 – 66

LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LT
A
B
LT

LIGHTING SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
General Precautions for Service Operations ............ 5
HEADLAMP - XENON TYPE - ................................... 6
Component Parts and Harness Connector Location ..... 6
System Description .................................................. 6
OUTLINE ............................................................... 6
LOW BEAM OPERATION ..................................... 7
HIGH BEAM OPERATION .................................... 7
FLASH-TO-PASS OPERATION ............................ 8
COMBINATION SWITCH READING FUNCTION ..... 8
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 8
AUTO LIGHT OPERATION ................................... 8
XENON HEADLAMP ............................................. 9
CAN Communication System Description ................ 9
CAN Communication Unit ........................................ 9
Schematic .............................................................. 10
Wiring Diagram — H/LAMP — ................................ 11
Terminals and Reference Values for BCM ............. 15
Terminals and Reference Values for IPDM E/R ..... 17
How to Perform Trouble Diagnosis ........................ 17
Preliminary Check .................................................. 17
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 17
CONSULT-II Functions (BCM) ............................... 18
CONSULT-II BASIC OPERATION ....................... 18
WORK SUPPORT ............................................... 19
DATA MONITOR ................................................. 19
ACTIVE TEST ..................................................... 20
CONSULT-II Functions (IPDM E/R) ....................... 20
CONSULT-II OPERATION .................................. 20
DATA MONITOR ................................................. 21
ACTIVE TEST ..................................................... 21
Headlamp Do Not Change To High (Both Sides) ... 22
Headlamp Does Not Change To High (One Side) ... 25
High Beam Indicator Does Not Illuminate .............. 26
Headlamp Do Not Illuminate (Both Sides) ............. 27
Headlamp Does Not Illuminate (One Side) ............ 29Headlamps Do Not Change to Low (Both Sides) ... 30
Headlamps Do Not Turn OFF ................................. 31
General Information for Xenon Headlamp Trouble
Diagnosis ................................................................ 32
Caution: .................................................................. 32
Xenon Headlamp Trouble Diagnosis ...................... 32
Aiming Adjustment .................................................. 33
PREPARATION BEFORE ADJUSTING .............. 33
LOW BEAM AND HIGH BEAM ........................... 33
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 34
Bulb Replacement .................................................. 35
HEADLAMP HIGH/LOW BEAM .......................... 35
BENDING LAMP ................................................. 35
PARKING LAMP .................................................. 35
FRONT TURN SIGNAL LAMP ............................ 35
Removal and Installation ........................................ 36
REMOVAL ........................................................... 36
INSTALLATION ................................................... 36
Disassembly and Assembly .................................... 37
DISASSEMBLY ................................................... 37
ASSEMBLY ......................................................... 37
HEADLAMP - HALOGEN TYPE - ............................ 38
Component Parts and Harness Connector Location ... 38
System Description ................................................. 38
OUTLINE ............................................................. 38
LOW BEAM OPERATION ................................... 39
HIGH BEAM OPERATION .................................. 39
FLASH-TO-PASS OPERATION .......................... 40
COMBINATION SWITCH READING FUNCTION ... 40
EXTERIOR LAMP BATTERY SAVER CONTROL ... 40
AUTO LIGHT OPERATION ................................. 40
CAN Communication System Description .............. 40
CAN Communication Unit ....................................... 40
Schematic ............................................................... 41
Wiring Diagram — H/LAMP — ............................... 42
Terminals and Reference Values for BCM .............. 46
Terminals and Reference Values for IPDM E/R ...... 48
How to Perform Trouble Diagnosis ......................... 48
Preliminary Check .................................................. 48

LT-2 CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 48
CONSULT-II Functions (BCM) ................................ 49
CONSULT-II Functions (IPDM E/R) ........................ 49
Headlamp High Do Not Illuminate (Both Sides) ...... 50
Headlamp High Does Not Illuminate (One Side) .... 53
High Beam Indicator Does Not Illuminate ............... 54
Headlamp Low Beam Does Not Illuminate (Both
Sides) ..................................................................... 54
Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 57
Headlamps High Do Not Go OFF (Both Sides) ...... 58
Headlamps Low Do Not Go OFF (Both Sides) ....... 59
Aiming Adjustment .................................................. 60
PREPARATION BEFORE ADJUSTING .............. 60
LOW BEAM AND HIGH BEAM ........................... 60
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 61
Bulb Replacement .................................................. 62
HEADLAMP (UPPER) HIGH BEAM .................... 62
HEADLAMP (LOWER) LOW BEAM .................... 62
PARKING LAMP .................................................. 62
FRONT TURN SIGNAL LAMP ............................ 62
Removal and Installation ........................................ 62
Disassembly and Assembly .................................... 63
DISASSEMBLY ................................................... 63
ASSEMBLY ......................................................... 63
AUTO LIGHT SYSTEM ............................................. 64
Component Parts and Harness Connector Location ... 64
System Description ................................................. 64
OUTLINE ............................................................. 64
AUTO LIGHT OPERATION ................................. 65
COMBINATION SWITCH READING FUNCTION ... 65
HEADLAMP LOW AND HIGH OPERATION
(XENON TYPE) ................................................... 65
HEADLAMP LOW AND HIGH OPERATION
(HALOGEN TYPE) .............................................. 65
FRONT FOG LAMP OPERATION ....................... 65
PARKING, LICENSE PLATE AND TAIL LAMPS
OPERATION ........................................................ 65
CAN Communication System Description .............. 65
CAN Communication Unit ....................................... 65
Major Components and Functions .......................... 65
Wiring Diagram — AUTO/L — ................................ 66
Terminals and Reference Values for BCM .............. 68
Terminals and Reference Values for IPDM E/R ...... 69
How to Perform Trouble Diagnosis ......................... 69
Preliminary Check .................................................. 70
SETTING CHANGE FUNCTIONS ....................... 70
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 70
CONSULT-II Functions (BCM) ................................ 71
Auto Light Function Does Not Operate ................... 71
Removal and Installation for Optical Sensor ........... 74
REMOVAL ........................................................... 74
INSTALLATION .................................................... 74
ACTIVE AFS ............................................................. 75
Component Parts and Harness Connector Location ... 75
System Description ................................................. 75AFS (ADAPTIVE FRONT-LIGHTING SYSTEM) ... 75
OUTLINE ............................................................. 76
BENDING LAMP OPERATION ............................ 76
CAN Communication System Description .............. 77
CAN Communication Unit ....................................... 77
Schematic ............................................................... 78
Wiring Diagram — AFS — ...................................... 79
Terminals and Reference Values for AFS Control
Unit .......................................................................... 82
CONSULT-II Functions (ADAPTIVE LIGHT) ........... 82
CONSULT-II BASIC OPERATION ....................... 82
WORK SUPPORT ............................................... 82
SELF-DIAG RESULTS ......................................... 84
DATA MONITOR .................................................. 86
ACTIVE TEST ...................................................... 87
AFS Operation Check (Function Test) .................... 88
Bending Lamps Do Not Illuminate (Both Side) ....... 90
Bending Lamp Does Not Illuminate (One Side) ...... 91
Bending Lamp Does Not turn OFF ......................... 92
DTC B2515 [ST ANG SEN SIG] ............................. 92
DTC B2516 [SHIFT POS SIG (P, R)] ...................... 93
DTC B2517 [VEHICLE SPEED SIG] ...................... 93
Aiming Adjustment .................................................. 94
Bulb Replacement ................................................... 94
Removal and Installation of AFS Control Unit ......... 94
REMOVAL ............................................................ 94
INSTALLATION .................................................... 94
Removal and Installation of Steering Angle Sensor ... 94
REMOVAL ............................................................ 94
INSTALLATION .................................................... 94
HEADLAMP AIMING CONTROL (AUTO) ................ 95
Component Parts and Harness connector Location ... 95
System Description ................................................. 96
OUTLINE ............................................................. 96
HEADLAMP AUTO AIMING CONTROL OPER-
ATION .................................................................. 97
CAN Communication System Description .............. 97
CAN Communication Unit ....................................... 97
Schematic ............................................................... 98
Wiring Diagram — H/AIM — ................................... 99
Terminals and Reference Values for Height Sensor .103
How to Proceed With Trouble Diagnosis ..............103
CONSULT-II Functions (HEADLAMP LEVELIZER) .103
CONSULT-II BASIC OPERATION .....................103
WORK SUPPORT .............................................103
DATA MONITOR ................................................104
ACTIVE TEST ....................................................105
SELF-DIAG RESULTS .......................................105
Check Aiming Control System ..............................107
Headlamp Aiming Motor Does Not Operate (Both
Sides) ....................................................................108
Headlamp Aiming Motor Does Not Operate (One
Side) ...................................................................... 111
DTC B2081 [INITIAL NOT DONE] ........................112
DTC B2082 [SENSOR OUT OF RANGE] .............112
DTC B2083 [SEN SIG NOT PLAUSIBLE] ............113
DTC B2084 [VOLTAGE UNDER LIMIT] ................113
DTC B2085 [LOW BEAM SIG OPEN LINE] .........114
DTC B2086 [FRQ. OVER LIMIT] ..........................115

LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
DTC B2087 [SHORT TO GROUND] ..................... 116
DTC B2088 [SHORT TO BATTERY] ..................... 118
Removal and Installation of Height Sensor .......... 120
REMOVAL ......................................................... 120
INSTALLATION ................................................. 120
HEADLAMP AIMING CONTROL (MANUAL) ........ 121
Schematic ............................................................ 121
Wiring Diagram — H/AIM — ................................ 122
Removal and Installation ...................................... 125
REMOVAL ......................................................... 125
INSTALLATION ................................................. 125
Switch Circuit Inspection ...................................... 125
FRONT FOG LAMP ................................................ 126
Component Parts and Harness Connector Location . 126
System Description .............................................. 126
OUTLINE ........................................................... 126
COMBINATION SWITCH READING FUNCTION . 127
EXTERIOR LAMP BATTERY SAVER CONTROL . 127
CAN Communication System Description ............ 127
CAN Communication Unit .................................... 127
Schematic ............................................................ 128
Wiring Diagram — F/FOG — ............................... 129
Terminals and Reference Values for BCM ........... 132
Terminals and Reference Values for IPDM E/R ... 133
How to Perform Trouble Diagnosis ...................... 133
Preliminary Check ................................................ 133
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. 133
CONSULT-II Functions (BCM) ............................. 134
CONSULT-II Functions (IPDM E/R) ..................... 134
Front Fog Lamps Do Not Illuminate (Both Sides) . 135
Front Fog Lamp Does Not Illuminate (One Side) . 137
Front Fog Lamp Indicator Lamp Does Not Illuminate . 138
Front Fog Lamps Does Not Go OFF (Both Sides) . 139
Aiming Adjustment ............................................... 140
Bulb Replacement ................................................ 141
Removal and Installation ...................................... 141
REMOVAL ......................................................... 141
INSTALLATION ................................................. 141
REAR FOG LAMP .................................................. 142
Component Parts and Harness Connector Location . 142
System Description .............................................. 142
OUTLINE ........................................................... 142
COMBINATION SWITCH READING FUNCTION . 143
EXTERIOR LAMP BATTERY SAVER CONTROL . 143
CAN Communication System Description ............ 143
CAN Communication Unit .................................... 143
Wiring Diagram — R/FOG — ............................... 144
Terminals and Reference Value for BCM ............. 146
How to Proceed With Trouble Diagnosis .............. 147
Preliminary Check ................................................ 147
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. 147
CONSULT-II Function (BCM) ............................... 148
Rear Fog Lamp Does Not Illuminate .................... 148
Rear Fog Lamp Indicator Lamp Does Not Illuminate . 150
Rear Fog Lamp Does Not Go OFF ...................... 151
Bulb Replacement ................................................ 151
Removal and Installation ...................................... 151TURN SIGNAL AND HAZARD WARNING LAMPS .152
Component Parts and Harness Connector Location .152
System Description ...............................................152
OUTLINE ...........................................................152
TURN SIGNAL OPERATION ............................153
HAZARD LAMP OPERATION ...........................153
INTERLOCKED HAZARD LAMP OPERATION
WITH REMOTE KEYLESS ENTRY SYSTEM ...154
INTERLOCKED HAZARD LAMP OPERATION
WITH INTELLIGENT KEY SYSTEM .................154
COMBINATION SWITCH READING FUNCTION .154
CAN Communication System Description ............154
CAN Communication Unit .....................................154
Schematic .............................................................155
Wiring Diagram — TURN — .................................156
Terminals and Reference Values for BCM ............159
How to Perform Trouble Diagnoses .....................160
Preliminary Check ................................................161
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................161
CONSULT-II Functions (BCM) ..............................162
CONSULT-II BASIC OPERATION .....................162
DATA MONITOR ...............................................162
ACTIVE TEST ...................................................162
Turn Signal Lamp RH Does Not Illuminate ...........163
Turn Signal Lamp LH Does Not Illuminate ...........167
Turn Signal Lamps Do Not Operate But Hazard
Warning Lamp Operate ........................................170
Hazard Warning Lamp Do Not Operate But Turn Sig-
nal Lamp Operate .................................................171
Turn Signal Indicator Lamp Does Not Illuminate ..173
Turn Signal Lamps Do Not Go OFF .....................173
Bulb Replacement ................................................175
SIDE TURN SIGNAL LAMP ..............................175
FRONT TURN SIGNAL LAMP ..........................175
REAR TURN SIGNAL LAMP ............................175
Removal and Installation ......................................175
SIDE TURN SIGNAL LAMP ..............................175
FRONT TURN SIGNAL LAMP ..........................175
REAR TURN SIGNAL LAMP ............................175
LIGHTING AND TURN SIGNAL SWITCH ..............176
Removal and Installation ......................................176
REMOVAL .........................................................176
INSTALLATION .................................................176
Switch Circuit Inspection ......................................176
HAZARD SWITCH ..................................................177
Removal and Installation ......................................177
REMOVAL .........................................................177
INSTALLATION .................................................177
COMBINATION SWITCH ........................................178
Wiring Diagram — COMB SW — .........................178
Terminals and Reference Values for BCM ............179
Combination Switch Reading Function .................183
CONSULT-II Functions (BCM) ..............................183
CONSULT-II BASIC OPERATION .....................184
DATA MONITOR ...............................................184
Combination Switch Inspection ............................185
Removal and Installation ......................................189
STOP LAMP ............................................................190

LT-4 Wiring Diagram — STOP/L — ..............................190
WITH REAR SUNSHADE AND REAR VIEW
CAMERA ...........................................................190
WITHOUT REAR SUNSHADE AND REAR VIEW
CAMERA ...........................................................191
Bulb Replacement ................................................192
HIGH-MOUNTED STOP LAMP .........................192
STOP LAMP ......................................................192
Removal and Installation ......................................192
HIGH-MOUNTED STOP LAMP .........................192
STOP LAMP ......................................................192
BACK-UP LAMP .....................................................193
Wiring Diagram — BACK/L — ..............................193
WITH A/T ...........................................................193
WITH CVT .........................................................194
Bulb Replacement ................................................195
Removal and Installation ......................................195
PARKING, LICENSE PLATE AND TAIL LAMPS ....196
Component Parts and Harness Connector Location .196
System Description ...............................................196
OUTLINE ...........................................................196
PARKING, LICENCE PLATE AND TAIL LAMPS
OPERATION ......................................................197
COMBINATION SWITCH READING FUNCTION .197
EXTERIOR LAMP BATTERY SAVER CONTROL .197
CAN Communication System Description ............198
CAN Communication Unit .....................................198
Schematic .............................................................199
Wiring Diagram — TAIL/L — ................................200
Terminals and Reference Values for BCM ............205
Terminals and Reference Values for IPDM E/R ....206
How to Perform Trouble Diagnoses ......................206
Preliminary Check ................................................206
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................206
CONSULT-II Functions (BCM) ..............................207
CONSULT-II Functions (IPDM E/R) ......................207
Parking, License Plate and Tail Lamps Do Not Illu-
minate ...................................................................208
Tail lamp Indicator Does Not Illuminate ................212
Parking, License Plate and Tail Lamps Do Not Go
OFF ......................................................................213
Bulb Replacement ................................................215
LICENSE PLATE LAMP ....................................215
PARKING LAMP ................................................215
TAIL LAMP ........................................................215
Removal and Installation ......................................215
LICENSE PLATE LAMP ....................................215
PARKING LAMP ................................................215
TAIL LAMP ........................................................215
REAR COMBINATION LAMP .................................216
Bulb Replacement ................................................216
REAR TURN SIGNAL LAMP BULB, BACK-UP
LAMP BULB AND STOP/TAIL LAMP BULB ......216
Removal and Installation ......................................216
REMOVAL .........................................................216
INSTALLATION ..................................................216
INTERIOR LAMP ....................................................217Wiring Diagram — INT/L — ..................................217
Bulb Replacement .................................................218
VANITY MIRROR LAMP ....................................218
INTERIOR ROOM LAMP ........................................219
Component Parts and Harness Connector Location .219
System Description ...............................................219
OUTLINE ...........................................................219
SWITCH OPERATION .......................................220
STEP LAMP OPERATION .................................221
TRUNK ROOM LAMP OPERATION ..................221
INTERIOR ROOM LAMP TIMER OPERATION .221
INTERIOR ROOM LAMP BATTERY SAVER
CONTROL .........................................................222
Schematic .............................................................223
Wiring Diagram — ROOM/L — .............................225
Terminals and Reference Values for BCM ............230
How to Perform With Trouble Diagnoses ..............231
Preliminary Check .................................................232
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ...................................................................232
CONSULT-II Functions (BCM) ..............................233
CONSULT-II BASIC OPERATION .....................233
WORK SUPPORT (INT LAMP) .........................233
DATA MONITOR (INT LAMP) ............................233
ACTIVE TEST ....................................................234
WORK SUPPORT (BATTERY SAVER) .............234
DATA MONITOR (BATTERY SAVER) ...............235
Interior Room Lamps Do Not Illuminate ................236
Interior Room Lamps Illuminate But Timer Does Not
Operate .................................................................240
Bulb Replacement .................................................241
MAP LAMP ........................................................241
STEP LAMP .......................................................241
PERSONAL LAMP .............................................241
TRUNK ROOM LAMP ........................................241
IGNITION KEYHOLE ILLUMINATION ...............242
Removal and Installation .......................................242
MAP LAMP ........................................................242
STEP LAMP .......................................................242
PERSONAL LAMP .............................................243
TRUNK ROOM LAMP ........................................243
ILLUMINATION ........................................................244
System Description ...............................................244
OUTLINE ...........................................................244
ILLUMINATION OPERATION BY LIGHTING
SWITCH .............................................................244
EXTERIOR LAMP BATTERY SAVER CONTROL .246
CAN Communication System Description ............246
CAN Communication Unit .....................................246
Schematic .............................................................247
Wiring Diagram — ILL — ......................................249
Bulb Replacement .................................................260
ASHTRAY ILLUMINATION ................................260
GLOVE BOX LAMP ...........................................260
CIGARETTE LIGHTER ILLUMINATION ............260
BULB SPECIFICATIONS ........................................261
Headlamp ..............................................................261
Exterior Lamp ........................................................261
Interior Lamp/Illumination ......................................261

HEADLAMP - XENON TYPE -
LT-11
C
D
E
F
G
H
I
J
L
MA
B
LT

Wiring Diagram — H/LAMP —BKS001MZ
TKWM4572E

HEADLAMP - XENON TYPE -
LT-17
C
D
E
F
G
H
I
J
L
MA
B
LT

Terminals and Reference Values for IPDM E/RBKS001N1
How to Perform Trouble DiagnosisBKS001N2
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 6 , "
System Description" .
3. Perform the Preliminary Check. Refer to LT- 1 7 , "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the headlamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Preliminary CheckBKS001N3
CHECK POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
Refer to LT- 11 , "Wiring Diagram — H/LAMP —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse or fusible link is blown, be sure to eliminate cause of malfunction before installing new fuse
or fusible link. Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
Terminal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
20 R/Y Headlamp low (RH) ON Lighting switch 2ND positionOFF Approx. 0 V
ON Battery voltage
27 L/W Headlamp high (RH) ONLighting switch HIGH BEAM
or PASSING positionOFF Approx. 0 V
ON Battery voltage
28 G Headlamp high (LH) ONLighting switch HIGH BEAM
or PASSING positionOFF Approx. 0 V
ON Battery voltage
30 L Headlamp low (LH) ON Lighting switch 2ND positionOFF Approx. 0 V
ON Battery voltage
38 B Ground ON — Approx. 0 V
48 L CAN− H— — —
49 P CAN− L— — —
60 B Ground ON — Approx. 0 V
Unit Power source Fuse and fusible link No.
BCMBatteryM
17
Ignition switch ACC or ON position 6
Ignition switch ON or START position 1
IPDM E/R Battery72
74
76
86

LT-42
HEADLAMP - HALOGEN TYPE -

Wiring Diagram — H/LAMP —BKS001NO
TKWM4574E