2003 NISSAN TEANA trunk

LT-216
REAR COMBINATION LAMP

REAR COMBINATION LAMPPFP:26554
Bulb ReplacementBKS001R0
REAR TURN SIGNAL LAMP BULB, BACK-UP LAMP BULB AND STOP/TAIL LAMP BULB
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Turn tail lamp bulb socket (1), rear turn signal lamp bulb socket
(2), back-up lamp bulb socket (3) (right side) and rear fog lamp
bulb socket (3) (left side) counterclockwise and unlock it.
3. Remove tail lamp bulb (4), rear turn signal lamp bulb (5), back-
up lamp bulb (6) (right side) and rear fog lamp bulb (6) (left
side).
Removal and InstallationBKS001R1
REMOVAL
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts (A).
4. Pull the rear combination lamp (1) toward rear of the vehicle and
remove clip (B) and locating pin (C) from the vehicle.
5. Remove seal packing (2) from rear combination lamp (1).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Seal packing cannot be reused.Tail lamp : 12V - 5W
Rear turn signal lamp : 12V - 21W
Back-up lamp (Right side) : 12V - 21W
Rear fog lamp (Left side) : 12V - 21W
Stop lamp : LED
SKIB8646J
PKIC9679J
Rear combination lamp mounting nut : 5.1 N·m (0.52 kg-m, 45 in-lb)

INTERIOR ROOM LAMP
LT-219
C
D
E
F
G
H
I
J
L
MA
B
LT

INTERIOR ROOM LAMPPFP:26410
Component Parts and Harness Connector LocationBKS001R4
System DescriptionBKS001R5
BCM (Body Control Module) controls the step lamp, the trunk room lamp, the interior room lamp timer and the
interior room lamp battery saver.
OUTLINE
Power is supplied at all times (without Intelligent Key system)

through 15A fuse [No. 17, located in fuse block (J/B)]

to key switch and key lock solenoid (key switch) terminal 1 and

to BCM terminal 42,

through 50A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55.
PKID0347E

INTERIOR ROOM LAMP
LT-221
C
D
E
F
G
H
I
J
L
MA
B
LT


through front door lock assembly (driver side) (door unlock sensor) terminal 4

through front door lock assembly (driver side) (door unlock sensor) terminal 5

through grounds M71 and M72.
With ground is supplied, BCM detects that the driver side door is unlocked.
When the front door lock assembly (driver side) (door unlock sensor) is OFF (door is locked), ground is not
supplied. And BCM detects that the driver side door is locked.
When the trunk lid lock assembly (trunk room lamp switch) is ON (trunk lid is opened), ground is supplied

to BCM terminal 57

through trunk lid lock assembly (trunk room lamp switch) terminal 3

through trunk lid lock assembly (trunk room lamp switch) terminal 1

through grounds B214 and B217.
With ground is supplied, BCM detects that the trunk lid is opened.
STEP LAMP OPERATION
When front door switch (driver side) or front door switch (passenger switch) is turned ON, front step lamp
(driver side) and front step lamp (passenger side) turns ON. Power is supplied

through 10A fuse [No. 21, located in fuse block (J/B)]

to front step lamp (driver side) terminal 1 and

to front step lamp (passenger side) terminal 1.
Ground is supplied

to front step lamp (driver side) terminal 2 and

to front step lamp (passenger side) terminal 2

through BCM terminal 47.
With power and ground supplied, front step lamp (driver side) and front step lamp (passenger side) illuminate.
And, front step lamp (driver side) and front step lamp (passenger side) turns OFF when front door switch
(driver side) and front door switch (passenger switch) are turned OFF.
TRUNK ROOM LAMP OPERATION
When trunk lid lock assembly (trunk room lamp switch) is turned ON (trunk lid is opened), trunk room lamp turn
ON. Power is supplied

through 10A fuse [No. 21, located in fuse block (J/B)]

to trunk room lamp terminal 1.
Ground is supplied

to trunk room lamp terminal 2

through BCM terminal 64.
With power and ground supplied, trunk room lamp illuminate.
And, trunk room lamp turns OFF when trunk lid lock assembly (trunk room lamp switch) is turned OFF.
INTERIOR ROOM LAMP TIMER OPERATION
The interior room lamp timer controls to turn ON/OFF of the map lamp, personal lamps and ignition keyhole
illumination when map lamp switch and personal lamp switch are in DOOR position.
BCM controls the interior room lamp timer according to the following signals.

Key switch signal

Door lock status signal (from front door lock assembly)

Front door switch (driver side) signal

Front door switch (passenger side) signal

Rear door switch RH signal

Rear door switch LH signal

Keyless lock/unlock signal (from remote keyless receiver)

Intelligent Key lock/unlock signal (from Intelligent Key unit through CAN communication)
And when those lamps are turned ON/OFF, the interior room lamp timer executes brightening/dimming control
for maximum 5 seconds. Brightening/dimming control time can be changed with CONSULT-II. Refer to LT- 2 3 3 ,
"WORK SUPPORT (INT LAMP)" .

INTERIOR ROOM LAMP
LT-231
C
D
E
F
G
H
I
J
L
MA
B
LT

NOTE:
*1:WIth Intelligent Key
*2:Without Intelligent Key
How to Perform With Trouble DiagnosesBKS001R9
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 2 1 9 , "
System Description" .
3. Perform the Preliminary Check. Refer to LT- 2 3 2 , "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the interior room lamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
52 B Ground ON — Approx. 0 V
55 W/BBattery power
supplyOFF
— Battery voltage
57 V/W Trunk switch signal OFFTrunk room lamp
switchON (open) Approx. 0 V
OFF (close) Battery voltage
62 SBFront door switch (driver
side) signalOFFFront door switch
(driver side)ON (open) Approx. 0 V
OFF (closed)
Approx. 7.5 - 8.0
63 R/WRear door switch LH sig-
nalOFF Rear door switch LHON (open) Approx. 0 V
OFF (closed)
Approx. 7.5 - 8.0
64 BR/W Trunk lamp output signal OFFTrunk room lamp
switchON (open) Approx. 12 V
OFF (close) Approx. 0 V Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
PKIB4960J
PKIB4960J

INTERIOR ROOM LAMP
LT-241
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS0040I
MAP LAMP
1. Remove lens using clip driver or suitable tool.
2. Remove bulb.
STEP LAMP
1. Remove front door step lamp. Refer to LT- 2 4 2 , "STEP LAMP" .
2. Remove bulb.
PERSONAL LAMP
1. Remove personal lamp. Refer to LT- 2 4 3 , "PERSONAL LAMP" .
2. Remove screw from back of personal lamp.
3. Insert a screwdriver or similar tool and remove lens.
4. Remove bulb.
TRUNK ROOM LAMP
Unfold pawl and remove lens, and remove bulb from bulb socket.Map lamp : 12V - 8W
SKIA8658E
Front door step lamp : 12V - 2.7W
SKIB0900E
Personal lamp : 12V - 8W
SKIA6359E
Trunk room lamp : 12V - 3.4W
SKIA6367E

INTERIOR ROOM LAMP
LT-243
C
D
E
F
G
H
I
J
L
MA
B
LT

PERSONAL LAMP
Removal
1. Use a clip driver or similar tool to press metal clip, and remove
personal lamp.
2. Disconnect personal lamp connector.
Installation
Installation is the reverse order of removal.
TRUNK ROOM LAMP
Removal
1. Remove rear parcel shelf finisher assembly. Refer to EI-43, "REAR PARCEL SHELF FINISHER" .
2. Disconnect trunk room lamp connector.
3. Press pawl and remove trunk room lamp.
Installation
Installation is the reverse order of removal.
SKIA6360E
SKIA6366E

BULB SPECIFICATIONS
LT-261
C
D
E
F
G
H
I
J
L
MA
B
LT

BULB SPECIFICATIONSPFP:26297
HeadlampBKS001RS
Exterior LampBKS001RT
Interior Lamp/IlluminationBKS001RU
Item Wattage (W)
Low/High (Xenon type)35 (D2S)
Low (Halogen type)55 (H11)
High (Halogen type)55 (H7)
Item Wattage (W)
Front combination lamp (Xenon type)Front turn signal lamp 21 (amber)
Parking lamp 5
Bending lamp 55 (H7)
Front combination lamp (Halogen type)Front turn signal lamp 21 (amber)
Parking lamp 5
Rear combination lampStop lamp LED
Tail lamp 5
Rear turn signal lamp 21
Back-up lamp 21
Rear fog lamp 21
Side turn signal lamp5
Front fog lamp35 (H8)
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Map lamp8
Personal lamp8
Trunk room lamp3.4
Ashtray illumination1.4
Step lamp2.7
Vanity mirror lamp1.8
Ignition key hole illumination1.4
Glove box lamp1.4
Cigarette lighter illumination1.4

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsBLS0005D
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
UNDER HOOD — engine off
Radiator coolant level and coolant hose connections for leaks
Battery fluid level, specific gravity and conditions of battery terminals
Drive belts tension
Fuel lines and connections for leaks
Engine oil level and oil leaks
Brake reservoir fluid level and fluid lines for leaks
Windshield and rear window washer and headlamp cleaner reservoir fluid level
Power steering reservoir fluid level and hose connections for leaks
ON INSIDE AND OUTSIDE
Remove front spring/strut spacer (If applicable)
Operation of all instruments, gauges, lights and accessories
Operation of horn(s), wiper and washer
Steering lock for operation
Check air conditioner for gas leaks
Front and rear seats, and seat belts for operation
All moldings, trims and fittings for fit and alignment
All windows for operation and alignment
Hood, trunk lid, door panels for fit and alignment
Latches, keys and locks for operation
Weatherstrips for adhesion and fit
Headlamp aiming
Tighten wheel nuts (Inc. inner nuts if applicable)
Tire pressure (Inc. spare tire)
Check front wheels for toe-in
Install clock/voltmeter/room lamp fuse (If applicable)
Install deodorizing filter to air conditioner (If applicable)
Remove wiper blade protectors (If applicable)
UNDER BODY
Transfer and differential gear oil level
Brake and fuel lines and oil/fluid reservoirs for leaks
Tighten bolts and nuts of steering linkage and gear box, suspension, propeller shafts and drive shafts
Tighten rear body bolts and nuts (Models with wooden bed only)
ROAD TEST
Clutch operation
Parking brake operation
Service brake operation
Automatic transmission/transaxle shift timing and kickdown
Steering control and returnables
Engine performance