2003 NISSAN TEANA trunk

EI-18
REAR BUMPER

REMOVAL
1. Fully open trunk lid assembly.
2. Remove trunk floor carpet, trunk box assembly, trunk floor spacer (LH/RH), trunk rear garnish, trunk rear
finisher, and trunk wheelhouse finisher. Refer to EI-58, "
TRUNK ROOM TRIM & TRUNK LID FINISHER" .
3. Remove rear combination lamp (LH/RH). Refer to LT- 2 1 6 , "
REAR COMBINATION LAMP" .
4. Remove clips of bumper fascia lower side.
5. Remove screws of bumper fascia left/right side.
6. Remove bumper fascia left/right bolt from trunk room inside.
7. Remove clip and bumper clamp from bumper fascia upper side, and then pull out bumper fascia toward
rear of vehicle.
8. Disconnect rear fog lamp harness connector after pulling out, and then remove bumper fascia.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
9. Remove the following parts after removing bumper fascia.

Bumper side bracket (LH/RH).

Rear bumper molding (LH/RH).
10. Remove bumper energy absorber.
11. Remove bumper reinforcement mounting nuts and bumper reinforcement.
12. Unscrew bumper stay mounting bolts, and remove bumper stay (LH/RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
1. Bumper stay (LH) 2. Bolt 3. Clip (C103)
4. Bolt 5. Nut 6. Clip (C205)
7. Screw 8. Bumper side bracket (LH) 9. Bumper fascia
10. Rear bumper molding 11. Rear bumper molding (LH) 12. Bumper side bracket (RH)
13. Bumper reinforcement 14. Bumper stay (RH) 15. Bumper lower bracket (RH)
16. Bumper lower bracket (LH) 17. Bumper clamp 18. Rear bumper protector
19. Bumper energy absorber Pawl
Portion Clearance
Rear bumper – Rear fender A – A 0.0 – 0.7 mm (0.000 – 0.028 in)
Rear bumper – Rear combination lamp B – B 0.2 – 3.8 mm (0.008 – 0.150 in)
Rear bumper – Trunk lid C – C 5.0 – 9.0 mm (0.197 – 0.354 in)

REAR WINDOW MOLDING
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI

REAR WINDOW MOLDINGPFP:79762
Removal and InstallationBIS0011N
REMOVAL AND INSTALLATION
Refer to GW-15, "Removal and Installation" in GW section for removal and installation of rear window glass
and molding.
PIIB1022E
1. Rear window glass 2. Spacer 3. Rear window molding
4. Dam rubber 5. Adhesive 6. Roof panel outer
7. Trunk lid outer panel

TRUNK LID FINISHER
EI-33
C
D
E
F
G
H
J
K
L
MA
B
EI

TRUNK LID FINISHERPFP:84810
Removal and InstallationBIS0011Q
REMOVAL
1. Fully open trunk lid.
2. Remove trunk lid finisher (inner). Refer to EI-35, "
DOOR FINISHER" .
3. Remove trunk lid finisher upper mounting nuts.
PIIA6259E
1. Nut 2. Seal 3. Stud bolt
4. Clip (C101) 5. Trunk lid finisher (upper) 6. Request switch harness connector
7. Trunk lid finisher (lower) 8. Clip 9. Grommet
10. Trunk lid 11. Double-faced adhesive tape
PIIA7080E

EI-34
TRUNK LID FINISHER

4. Remove trunk lid finisher upper mounting clips, and then pull out
trunk lid finisher upper toward rear of vehicle.
5. Disconnect request switch harness connector (only for models with intelligent key) after pulling out, then
remove trunk lid finisher upper.
6. Continuously, remove trunk lid finisher lower mounting clips the same as in step 4, and then remove trunk
lid finisher lower.
CAUTION:
After removal, visually inspect finisher, and if it is deformed, replace it with new molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Replace double-faced adhesive tape on back of finisher with a new tape if trunk lid finisher (lower)
is reused.

Remove double-faced adhesive tape remaining on body and back of finisher using double-faced
adhesive tape remover (SUMITOMO 3M Cleaner 30 or equivalent) when removing finisher (lower).

Install after cleaning adhesive parts of body side and back of finisher (lower).

Do not wash the vehicle within 24 hours after installing so as to keep adhesive.
PIIA7081E

DOOR FINISHER
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI

DOOR FINISHERPFP:80900
Removal and InstallationBIS0011R
1. Cap 2. Power window switch finisher (front) 3. Front door finisher
4. Front door inside seal 5. Door grip upper bracket 6. Door grip
7. Door grip finisher 8. Step lamp 9. Trunk & fuel lid opener switch
10. Seat memory switch 11. Seat memory switch finisher 12. Metal clip
13. Power window switch finisher (rear) 14. Rear door finisher
Clip Pawl Metal clip
PIIB8684E

EI-36
DOOR FINISHER

FRONT AND REAR DOOR FINISHER
Removal
1. Fully open door window.
2. Remove inside handle escutcheon cap.
3. Remove inside handle escutcheon screw.
4. Insert a remover tool A into power window switch finisher (front)
(1), lift up front end and disengage metal clip. Pull out finisher
toward front of vehicle.
CAUTION:
Lift up rear end of power window switch finisher (rear) and
disengage metal clips, and then pull out finisher toward
rear of vehicle.
5. Disconnect power window switch harness connector after pulling out, and then remove power window
switch finisher.
6. Remove power window switch screws.
7. Insert a clip clamp remover into clips on back of door trim, and
disengage clips.
CAUTION:
Insert a clip clamp remover into the part shown by the
arrow (between the clips and the body side panel). Remove
door trim.
8. Disconnect harness connector for trunk lid opener after disengaging.
9. Disconnect harness connector for seat memory switch (1) and
indirect lighting (2).
10. Disconnect harness connector for step lamp.
11. Pull up door trim and pull out toward vehicle inside, and then dis-
connect inside handle cable (3) and lock knob cable (2) from
inside handle (1).
PIIB8685E
SIIA0810E
PIIB8687E
PIIB8686E

DOOR FINISHER
EI-37
C
D
E
F
G
H
J
K
L
MA
B
EI

12. Remove door trim.
13. Remove the following parts after removing door trim.

Inside handle assembly

Trunk lid opener switch

Step lamp (front only)

Door grip

Front door inside handle

Door grip upper bracket

Seat memory switch (With automatic drive positioner)
Installation
Install in the reverse order of removal.
CAUTION:
When installing door trim, make sure that clips are securely fitted in panel holes on body, and then
press them in.

EI-44
REAR PARCEL SHELF FINISHER

REMOVAL
1. Remove rear seatback and rear seat cushion. Refer to SE-112, "REAR SEAT" .
2. Remove rear seat belt floor anchor bolt and rear seat belt shoulder anchor bolt. Refer to SB-5, "
Removal
and Installation of Rear Seat Belt" .
3. Disengage child anchor cover front pawls, and then pull out child
anchor cover (LH/RH center) toward front of vehicle.(Models
with rear window sunshade)
4. Remove rear kicking plate inner, rear seatback finisher, rear pillar finisher. Refer to EI-38, "
BODY SIDE
TRIM" .
5. Disconnect high-mounted stop lamp harness connector from
trunk room side. (Models without rear window sunshade)
6. Disconnect high-mounted stop lamp harness connector from
front side of rear parcel shelf finisher. (Models with rear window
sunshade)
7. Remove rear parcel shelf finisher mounting clip using a clip clamp remover.
8. Remove rear parcel shelf finisher while disengaging dual-lock fastener on back of rear parcel shelf fin-
isher. (Models with rear window sunshade)
9. Remove the following parts after removing rear parcel shelf finisher.

Rear speaker grille (for woofer)

High-mounted stop lamp
INSTALLATION
Install in the reverse order of removal.
7. Screw 8.Rear parcel shelf finisher (with sun-
shade)9. Child anchor cover (LH/RH center)
10. Rear window sunshade 11. Bolt 12. Locating pin
PIIA9530E
PIIA9531E
PIIA9535E