2003 MITSUBISHI SHOGUN instrument panel

I04A196A
Indicator lamps
A- Selector lever position indicator lamps
B-“N”indicator lamp
The indicator lamps in the instrument panel
are for indicating the selector lever posi-
tion and one of them will be illuminated
when the ignition is switched“ON”.
CAUTION
If the“N”(NEUTRAL) indicator lamp
(B) in the selector lever position indi-
cator flashes while you are driving,
the automatic transmission safety
device may be operating due to a
malfunction. (If the selector lever
position is in the“P”(PARK),“R”
(REVERSE) or“N”(NEUTRAL) posi-
tion, the indicator lamp does not
flash.)
Have your vehicle inspected by an
authorized MITSUBISHI dealer as
soon as possible.
Selector positions
(Main gate)
EI04BACb
P - PARK
The“P”(PARK) position supplements the
parking brake by locking the transmis-
sion while the vehicle is parked.
The engine can be started in this posi-
tion.
Apply the parking brake before leaving the
vehicle in this position.
R - REVERSE
Shift into this position only after the vehicle
has come to a complete stop.
CAUTION
Never shift into the“P”(PARK) or
“R”(REVERSE) position while the
vehicle is in motion. If the lever is
shifted into the“P”or“R”position
while the vehicle is in motion, the
transmission may be damaged.
N - NEUTRAL
At this position the transmission is disen-
gaged. It is the same as the neutral posi-
tion on a manual transmission, and should
be used when the vehicle is stationary for
an extended length of time during driv-
ing, such as in a traffic jam.
Starting and driving
5-19
Div:
Out put date:

To listen to a disc1. Insert the disc with the label facingupward.
When a disc is inserted, the CD player
will begin playing even if the radio or
tape player is being used.
2. To adjust the volume and tone, use the controls on the radio.
Refer to “How to adjust the volume ”and
“ How to adjust the tone ”on page 6-4.
3. When the eject button (1) is pressed, the disc will automatically stop and be
ejected.
4 . Whe nthe 3-inc hcompac tdis cis used,
playback can be made without using the
adapter. Insert the disc about in the cen-
tre of the discloading slot.
5. For information concerning the han- dling of compact discs, refer to the sec-
tion “Handling of compact discs ”on
page 6-33.
H12H079A
How to set CD autochanger*
EH12HAAb
The CD autochanger is located under the
centre of the instrument panel. It can
accommodate up to 6 discs.
NOTE
The 8 cm disc cannot be used in this com-
pact disc player.
H12H088A
How to set a disc1. Press one of the disc selection but- tons (1) to select the disc number which
you would like to insert.
2. The lamp of the disc (2) selected will turn orange.
3. Confirm that the LOAD indicator (3) also turns on. Should this not occur, it will
indicate that a disc is already inserted.
Press the eject button (4) to eject that
disc. The new disc may now be
inserted.
4. Press the disc in the slot (5) and give it a light push to set it in place.
For pleasant driving
6-31
Div:
Out put date:

H23A254A
RHDNOTE
On an air conditioned vehicle, the cool air
from the ventilators may appear as a mist.
This is due to moist air being suddenly
cooled by the air conditioning. This will clear
after a few moments.
CAUTION
(1) When using the air condition-
ing, the idling speed may slightly
increase as the air condition-
ing compressor is switched
on/off automatically. Especially
for vehicles with an automatic
transmission, while the vehicle
is stationary, fully depress the
brake pedal to prevent the
vehicle from creeping.
CAUTION
(2) On 3500 models, if a problem is
detected in the air conditioning
compressor, the air condition-
ing operation indicator lamp
blinks. Stop the vehicle in a safe
place, turn off the engine, then
restart the engine. If the air con-
ditioning operation indicator
lamp does not blink, there is no
problem. If it does blink, have it
checked at an authorized MIT-
SUBISHI dealer.
2- Blower speed selection dial
There are 4 blower speeds for control of
the amount of air flow.
Adjust the blower speed by turning the
blower speed selection dial clockwise or
anticlockwise.
The setting for ordinary use should be
the first or second speed.
3- Temperature control dial
The heater will not operate if the dial is
set all the way to the left.
The air flow temperature will gradually
increase as the dial is turned to the right.
NOTE
When the engine coolant temperature is
low, temperature of air introduced into the
passenger compartment does not change
even if the temperature control dial is
moved to the high temperature side.
H16A296A
MODE SELECTION AIR OUTLETS
B, CB, C, D, EA*, C*, D, EA, C*, D, EA, C*
A:From front and side demister
B:From centre ventilators
C:From side ventilators
D:From under the instrument panel
E:From rear end of the centre console
* :means a small amount of air flow
For pleasant driving
6-37
Div:
Out put date:

H14D114A
RV meter
H16A296A
MODE SELECTION AIR OUTLETS
B, CB, C, D, EA*, C*, D, EA, C*, D, EA, C*
A:From front and side demister
B:From centre ventilators
C:From side ventilators
D:From under the instrument panel
E:From rear end of the centre console
*:means a small amount of air flow
(Face position)
Air flows to the upper part of the
passenger compartment.(Foot/face position)
Air flows to the upper part of the
passenger compartment, and the leg
area.(Foot position)
Air flows to the leg areas.(Foot/demister position)
Air flows to the leg areas, wind-
screen and door windows.(Demister position)
Air flows to the windscreen and the
door windows.
NOTE
Air always flows out from the side ventila-
tors regardless of the mode selection dial
position.
For pleasant driving
6-47
Div:
Out put date:

CAUTION
(1) Do not attempt to start the
engine by pulling or pushing the
vehicle.
It could damage your vehicle.
(2) Always wear protective eye
goggles when working near the
battery.
(3) Keep the battery out of the reach
of children.
NOTE
On a vehicle with an anti-lock brake sys-
tem, if the vehicle is started or put in motion
without fully charging the battery, it might
cause the loss of smooth engine opera-
tion and it might cause the anti-lock brake
warning lamp to illuminate.
Refer to“Anti-lock brake system (ABS)”on
page 5-45.
What to do if the engine speed
becomes unstable after the bat-
tery is replaced
EN38B-G
If the engine speed becomes unstable after
the battery is replaced, reset the engine
using the following method:
1. Stop the vehicle in a safe place.
2. Place the gear shift lever (manual
transmission) in the“N”(Neutral) or the
selector lever (automatic transmission)
in the“P”(PARK) position.
Stop the engine.
3. Restart the engine.
4. Turn off the air conditioning.
5. Allow the engine to warm up until the
needle in the water temperature gauge
stabilizes near the centre of the gauge.
6. Stop and restart the engine.
7. Allow the engine to idle for approxi-
mately 10 minutes.
8. When the engine speed stabilizes, the
resetting procedure is complete.
NOTE
If the engine speed remains unstable after
the resetting procedure has been per-
formed, have the vehicle inspected by an
authorized MITSUBISHI dealer.
N09A135A
Fuses
EN09AABa
Fuse blockTo prevent damage to the electric system
due to short-circuiting or overloading, each
individual circuit is provided with a fuse.
There are fuse housings in the passen-
ger compartment and in the engine com-
partment.
The fuse housing in the passenger com-
partment is located in front of the driver’s
seat at the position shown in the illustra-
tion.
The replacement of fuses located in the
passenger compartment should be per-
formed from below the instrument panel.
For emergencies
8-28Div:
Out put date:

N09A136A
Changing a fuse
EN29C-Vb
1. Before replacing a fuse, always turn off
the electrical circuit concerned and place
the ignition switch in the“LOCK”posi-
tion.
2. Pull the fuse box lid (A) to remove it.
3. Remove the fuse puller (B) from the fuse
box lid (A).
N09A135A
4. The replacement of fuses located in the
driver’s seat foot area should be per-
formed from below the instrument panel.
N29C023A
5. Referring to the fuse load capacity table,
check the fuse pertaining to the prob-
lem.
C- Fuse is OK
D- Blown fuse
NOTE
If any system does not function but the fuse
corresponding to that system is normal,
there may be a fault in the system or else-
where.
Have your vehicle checked by an autho-
rized MITSUBISHI dealer.
For emergencies
8-33
Div:
Out put date: