2003 MAZDA MODEL MPV Owners Manual (in English)

7-4
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G

Jack
To remove the jack
1. Remove the cover.
2. Remove the tool bag.
3. Turn the wing bolt counterclockwise.To secure the jack
Perform the removal procedure in reverse.

Spare Tire
Your Mazda has a temporary spare tire.
The temporary spare tire is lighter and
smaller than a conventional tire, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spares should
NEVER be used for long drives or
extended periods.
Tool bag
Wing bolt
Jack
Driving with a Temporary Spare Tire
on Ice or Snow:
Driving with a spare tire on the front
(driving) wheels on ice or snow is
dangerous. Handling will be affected.
You could lose control of the vehicle
and have an accident. Put the spare
tire on the rear axle and move a
regular tire to the front.
WARNING
J16L_8R21-EA-02G.book Page 4 Saturday, June 8, 2002 11:16 AM

7-5
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
To remove the spare tire
1. Have everyone get out of the vehicle
and away from the vehicle and traffic.
2. For side-spoiler equipped vehicles,
remove the fasteners on both sides of
the spoiler cap by turning them
counterclockwise.
Pull the spoiler cap out and to the left. To avoid damage to the temporary
spare or to the vehicle, observe the
following precautions:
•Don’t exceed 80 km/h (50 mph).
•Avoid driving over obstacles.
Also, don’t drive through an
automatic car wash. This tire’s
diameter is smaller than a
conventional tire’s, so the ground
clearance is reduced about 25 mm
(1 in).
•Don’t use a tire chain on this tire
because it won’t fit properly.
•Don’t use your temporary spare on
any other vehicle; it has been
designed only for your Mazda.
•Do not tow a trailer while using this
tire.
•Use only one temporary spare tire
on your vehicle at the same time.CAUTION
NOTE
•Install the side spoiler cap in reverse
order of removal.
•After installing the side spoiler cap,
make sure it is securely attached.
Fastener
Spoiler cap
J16L_8R21-EA-02G.book Page 5 Saturday, June 8, 2002 11:16 AM

7-6
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
3. Locate the spare tire carrier socket cap
on the right, in front of the second-row
seat. Unscrew it by turning it
counterclockwise.
4. Remove the spare tire lever and lug
wrench from the tool bag.
5. Raise the reclining lever and lower the
seatback forward.
Make sure the seatback is locked.
6. Insert the spare tire lever into the spare
tire carrier socket. Fit the lug wrench to
the opposite end of the spare tire lever.7. Slowly turn the lug wrench
counterclockwise until the spare tire
reaches the ground and the cable
becomes loose.
Lug wrench
Spare tire
lever
•Turning the lug wrench without
reclining the seat could damage the
seatback.
•Applying excessive lateral force
while the spare tire lever is attached
may result in damage to the socket.
NOTE
The spare tire lever remains locked in
the socket while the spare tire is being
lowered.
Unless the cable is rolled up
completely, the spare tire lever cannot
be removed from the socket.
Spare tire
CAUTION
J16L_8R21-EA-02G.book Page 6 Saturday, June 8, 2002 11:16 AM

7-7
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
8. Rotate the small lever on top of the
retaining plate and pull the retaining
plate out from the center hole of the
tire.
To secure the spare tire
1. Place the tire with the outer side facing
upward, rotate the small lever on top of
the retaining plate and slide the
retaining plate through the center hole
of the tire.
Rotate the small lever into place.
2. Raise the spare tire slowly in reverse
order of removal.3. Replace the spare tire carrier cap in the
socket and turn it until the spare tire is
pulled up tight.
Retaining
plate
Retaining
plate
Retaining
plate
Lever
Spare tire
•Applying excessive lateral force
while the spare tire lever is attached
may result in damage to the socket.
•Place the specialized temporary
spare tire in the spare tire carrier
correctly.
Placing the specialized temporary
spare tire wrong side up or using
any tire other than the small
temporary spare tire designed for
use with this vehicle will result in
poor attachment and insufficient
ground clearance in the spare tire
carrier and the danger of the tire
falling off.
NOTE
Unless the cable is rolled up
completely, the spare tire lever cannot
be removed from the socket.
CAUTION
J16L_8R21-EA-02G.book Page 7 Saturday, June 8, 2002 11:16 AM

7-8
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
If you have a flat tire, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tire.
Stopping in traffic or on the shoulder of a
busy road is dangerous. •If you hear rattling from the spare
tire carrier while the vehicle is
moving, the spare tire carrier cable
may be cut.
Have it repaired at an Authorized
Mazda Dealer as soon as possible.
•When the spare tire carrier socket
cap is screwed completely tight, the
spare tire is locked in the highest
position.
If the spare tire carrier socket cap is
not screwed completely tight and
the cable is by chance cut, the spare
tire could fall off.
CAUTIONChanging a Flat Tire
NOTE
If the following occurs while driving, it
could indicate a flat tire.
•Steering becomes difficult.
•The vehicle begins to vibrate
excessively.
•The vehicle pulls in one direction.
Jacking a Vehicle:
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a
jack.
Passenger in Vehicle Supported by a
Jack:
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury. Never allow anyone inside a
vehicle supported by a jack.
WARNING
J16L_8R21-EA-02G.book Page 8 Saturday, June 8, 2002 11:16 AM

7-9
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Shift into Park (P) and turn off the
engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tire
(page 7-3).
6. Block the wheel diagonally opposite
the flat tire. When blocking a front
wheel, place the block both in front and
behind the tire. When blocking a rear
wheel, place the block both in front and
behind the tire.

Removing a Flat Tire
1. Pry off the wheel cover with the
beveled end of the jack lever.
NOTE
Make sure the jack is well lubricated
before using it.If the jack leans towards the front or
the rear when jacking up, lower the
vehicle until the wheels are firmly on
the ground. Then confirm that the
parking brake is set, the shift lever is in
Park (P), then push the blocks firmly
under the blocked tire.
NOTE
Force the end of the jack lever firmly
between wheel and cover, or removal
will be difficult.
CAUTION
Jack leverWheel cover
J16L_8R21-EA-02G.book Page 9 Saturday, June 8, 2002 11:16 AM

7-10
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
2. Loosen the lug nuts by turning them
counterclockwise one turn each, but
don’t remove any until the tire has been
raised off the ground.3. Place the jack under the jacking
position closest to the tire being
changed.
Align the notch on the wheel cover
with the valve stem when installing it.
Damage could occur during
installation if the wheel cover is not
properly aligned.
CAUTION
Tire valve
Notch
Incorrect Jacking Position:
Attempting to jack the vehicle in
positions other than those
recommended in this manual is
dangerous. The vehicle could slip off
the jack and seriously injure or even
kill someone. Use only the front and
rear jacking positions recommended
in this manual.
Improper Jack:
Using a jack that isn’t designed for
your Mazda is dangerous. The vehicle
could slip off the jack and seriously
injure someone. Use only the jack
provided with your Mazda.
Placing Objects Under the Jack:
Jacking the vehicle with an object
under the jack is dangerous. The jack
could slip and someone could be
seriously injured by the jack or the
falling vehicle. Never place objects
under the jack.
Jacking position
WARNING
J16L_8R21-EA-02G.book Page 10 Saturday, June 8, 2002 11:16 AM

7-11
In Case of an Emergency
Flat Tire
Form No. 8R21-EA-02G
4. Insert the jack lever and attach the lug
wrench to tire jack.
5. Turn the lug wrench clockwise and
raise the vehicle high enough so that
the spare tire can be installed. Before
removing the lug nuts, make sure your
Mazda is firmly in position and that it
cannot slip or move.
6. Remove the lug nuts by turning them
counterclockwise; then remove the
wheel.
Locking Lug Nuts
If your vehicle has optional antitheft
wheel lug nuts, one on each wheel will
lock the tires and you must use a special
key to unlock them. This key is attached
to the lug wrench and is stored with the
spare tire. Register them with the lock
manufacturer by filling out the card
provided in the glove box and mailing it in
the accompanying envelope. If you lose
your key, consult an Authorized Mazda
Dealer or use the lock manufacturer’s
order form, which is with the registration
card.
To remove an antitheft lug nut
1. Get the key for the locking lug nut.
2. Place it on top of the nut, and be sure to
hold the key square to it. If you hold
the key at an angle, you may damage
both key and nut. Don’t use a power
impact wrench.
3. Place the lug wrench on top of the key
and apply pressure. Turn the wrench
counterclockwise.
Lug wrench
Jack lever
Antitheft lug nutSpecial key
J16L_8R21-EA-02G.book Page 11 Saturday, June 8, 2002 11:16 AM