2003 Hyundai H-1 (Grand Starex) ignition

1-1
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
B000A01P-GAT 1.1.
1.1.
1.
BEFORE DRIVING
BEFORE DRIVING BEFORE DRIVING
BEFORE DRIVING
BEFORE DRIVING
YY
YY
Y
OUR
OUR OUR
OUR
OUR VEHICLE
VEHICLE VEHICLE
VEHICLE
VEHICLE
B010B01P-GAT Before entering the vehicle
Before entering the vehicle Before entering the vehicle
Before entering the vehicle
Before entering the vehicle
o Check that windows, mirrors and lights are clean.
o Check if any tire is low or flat.
o Look for fluid leaks.
o Check that area is clear if you’re about to back up.
B010C03P-GAT After entering the vehicle
After entering the vehicle After entering the vehicle
After entering the vehicle
After entering the vehicle
o Lock all doors.
o The driver and passengers are wearing prop- erly adjusted seat belts.
o The head restraints are properly adjusted, if so equipped.
o Adjust inside and outside mirrors.
o Check warning lights for correct operation, with the ignition key in the position "ON".
o Check all gauges, for normal operation.
B010A01P-GAT
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
SAFETY CHECKS
SAFETY CHECKS SAFETY CHECKS
SAFETY CHECKS
SAFETY CHECKS
Be sure you know your vehicle and its equip-
ment and how to use it safely.
B020A01P-GATRUNNING-IN RECOMMENDATIONS
RUNNING-IN RECOMMENDATIONS RUNNING-IN RECOMMENDATIONS
RUNNING-IN RECOMMENDATIONS
RUNNING-IN RECOMMENDATIONS During the running-in period for the first
1,000km(600miles), it is advisable to drive your new vehicle using the following precautions asa guideline to aid long life as well as futureeconomy and performance.
1. Do not race the engine at high speeds.
2. Avoid rapid starting, acceleration, braking and prolonged high-speed running.
3. Keep to the running-in speed limit shown below. B030A01P-GAT
BEFORE OPERATION
BEFORE OPERATION BEFORE OPERATION
BEFORE OPERATION
BEFORE OPERATION
PRECAUTIONS FOR NEW VEHICLE
PRECAUTIONS FOR NEW VEHICLE PRECAUTIONS FOR NEW VEHICLE
PRECAUTIONS FOR NEW VEHICLE
PRECAUTIONS FOR NEW VEHICLE The performance and life of a vehicle depend
largely on how the vehicle is handled when new.
To maintain the parts smoothly and sustain
high performance for a long time to come, besure to observe the following points.
Make sure that your vehicle does not miss
Make sure that your vehicle does not miss Make sure that your vehicle does not miss
Make sure that your vehicle does not miss
Make sure that your vehicle does not miss the first 5,000 km inspections.
the first 5,000 km inspections. the first 5,000 km inspections.
the first 5,000 km inspections.
the first 5,000 km inspections.
After the first 5,000 km of driving, take your vehicle
to your nearest service shop for inspection.
Drive range
1st
2nd 3rd4th 5thRunning-in speed
0~25(0~16)
20~50(13~31) 30~80(19~50)
40~(25~)50~(32~) km/h (mph)
WARNING: (Diesel only)
WARNING: (Diesel only) WARNING: (Diesel only)
WARNING: (Diesel only)
WARNING: (Diesel only)
To ensure that sufficient vacuum exists with-
To ensure that sufficient vacuum exists with- To ensure that sufficient vacuum exists with-
To ensure that sufficient vacuum exists with-
To ensure that sufficient vacuum exists with-in the brake system during cold weather
in the brake system during cold weather in the brake system during cold weather
in the brake system during cold weather
in the brake system during cold weather
start-up conditions, it is necessary to run
start-up conditions, it is necessary to run start-up conditions, it is necessary to run
start-up conditions, it is necessary to run
start-up conditions, it is necessary to run
the engine at idle after starting the engine.
the engine at idle after starting the engine. the engine at idle after starting the engine.
the engine at idle after starting the engine.
the engine at idle after starting the engine.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
Fluid levels, such as engine oil, engine cool-
Fluid levels, such as engine oil, engine cool- Fluid levels, such as engine oil, engine cool-
Fluid levels, such as engine oil, engine cool-
Fluid levels, such as engine oil, engine cool-ant, brake fluid, and windshield washer flu-
ant, brake fluid, and windshield washer flu- ant, brake fluid, and windshield washer flu-
ant, brake fluid, and windshield washer flu-
ant, brake fluid, and windshield washer flu-
id, should be checked daily and/or weekly,
id, should be checked daily and/or weekly, id, should be checked daily and/or weekly,
id, should be checked daily and/or weekly,
id, should be checked daily and/or weekly,
or whenever you refuel.
or whenever you refuel. or whenever you refuel.
or whenever you refuel.
or whenever you refuel.
Further details are described in the "CON-
Further details are described in the "CON- Further details are described in the "CON-
Further details are described in the "CON-
Further details are described in the "CON-SUMER INFORMATION" section.
SUMER INFORMATION" section. SUMER INFORMATION" section.
SUMER INFORMATION" section.
SUMER INFORMATION" section.
11
11
1
Please note that the legal speed limits dis-
played must be adhered to.
4. Do not exceed loading limits.
5. Refrain from towing a trailer.

BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
1-4 B100A02P-GAT
TT
TT
T HE USE OF KEYS
HE USE OF KEYS HE USE OF KEYS
HE USE OF KEYS
HE USE OF KEYS
B100A01P-GAG
23
5,6 1
4
B100B01P
1. IGNITION SWITCH
2. FRONT DOOR (DRIVER'S DOOR)
3. FRONT DOOR (PASSENGER'S DOOR)
4. SLIDING DOOR
5. TAILGATE
6. TWIN SWING DOOR (If installed)
7. FUEL TANK CAP (TRUCK ONLY)
31 2
7
B030A01E
B030A01A-AAT
KEYS
KEYS KEYS
KEYS
KEYS For greater convenience, the same key oper-
ates all the locks in your Hyundai. However, because the doors can be locked without a key,carrying a spare key is recommended in caseyou accidentally lock one key inside the car. B030B01A-AAT
Record Your Key Number
Record Your Key Number Record Your Key Number
Record Your Key Number
Record Your Key NumberB030B01E
A code number is stamped on the number plate that came with the keys to your Hyundai. Thiskey number plate should not be left with thekeys but kept in a safe place, not in the vehicle.The key number should also be recorded in aplace where it can be found in an emergency. If you need additional keys, or if you should lose your keys, your authorized Hyundai dealer canmake new keys if you can supply the keynumber.

BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
1-6 In the interest of security, the metal tag attached
to the keys which bears the key number should be removed from the key ring after delivery. Inaddition, key numbers cannot be provided byHyundai for security reasons.
If you need additional keys or if you should lose
your keys, your authorized Hyundai dealer canmake new keys if you can supply the keynumber and ID key. 2. Wait for 3~10 seconds.
3. You may set the remaining number of digits
by following the same procedures 1 and 2.
4. If all of four digits have been tried success- fully, from this time, you have to start your engine within 30 seconds. If you start yourengine after 30 seconds, your engine will notstart.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the engine dies while driving after limp
If the engine dies while driving after limp If the engine dies while driving after limp
If the engine dies while driving after limp
If the engine dies while driving after limp home procedure, you can start your engine
home procedure, you can start your engine home procedure, you can start your engine
home procedure, you can start your engine
home procedure, you can start your engine
within 8 seconds in condition of ignition
within 8 seconds in condition of ignition within 8 seconds in condition of ignition
within 8 seconds in condition of ignition
within 8 seconds in condition of ignition
OFF without limp home procedure again.
OFF without limp home procedure again. OFF without limp home procedure again.
OFF without limp home procedure again.
OFF without limp home procedure again.
After doing the limp home procedure, you have
to consult with your authorized Hyundai dealer as soon as possible.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
If you cannot start your engine in spite of limphome procedure, have your vehicle towed byan authorized Hyundai dealer.
B880D02E-GAT
Limp
Limp Limp
Limp
Limp
HH
HH
H
ome
ome ome
ome
ome
PP
PP
P
rocedures
rocedures rocedures
rocedures
rocedures
In case the immobilizer system is out of order,
you cannot start the engine without the limphome procedures with ignition key.
The following procedure is how to start the
engine with the function of the limp home. (0, 1,2, 3 as a sample password).
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
You can get the limp home password when
You can get the limp home password when You can get the limp home password when
You can get the limp home password when
You can get the limp home password when the vehicle is first delivered to you. If you do
the vehicle is first delivered to you. If you do the vehicle is first delivered to you. If you do
the vehicle is first delivered to you. If you do
the vehicle is first delivered to you. If you do
not have the password, consult your autho-
not have the password, consult your autho- not have the password, consult your autho-
not have the password, consult your autho-
not have the password, consult your autho-
rized Hyundai dealer.
rized Hyundai dealer. rized Hyundai dealer.
rized Hyundai dealer.
rized Hyundai dealer.
1. To set the password, you may turn the
ignition key "ON" and then turn it "OFF" according to the digit numbers. For example,turn the ignition key once for digit number"1", and twice for "2", and so on. However,for the digit number "0", you must turn theignition key for 10 times. B885B01P-GAT
Keys
Keys Keys
Keys
Keys
B880B01O
B885A01O-GAT
IMMOBILIZER SYSTEM
IMMOBILIZER SYSTEM IMMOBILIZER SYSTEM
IMMOBILIZER SYSTEM
IMMOBILIZER SYSTEM
(If Installed)
(If Installed) (If Installed)
(If Installed)
(If Installed) The immobilizer system is an anti-theft device, designed to deter automobile theft.
Without Theft-alarm system
B880B02P
With Theft-alarm system

1-7
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
B885D01A-GATLimp
Limp Limp
Limp
Limp HH
HH
H ome
ome ome
ome
ome
PP
PP
P
rocedures
rocedures rocedures
rocedures
rocedures
B880D01P
In case the immobilizer warning indicator blinks for five seconds when the ignition key is turnedto "ON" position, this indicates that the immobi-lizer system is out of order. And you cannotstart the engine without the limp home proce-dures with ignition key.
Hyundai dealer by quoting the relevant key number. In the interest of security, the metal tag at-
tached to the keys which bears the key numbershould be removed from the key ring after youreceive your new vehicle. In addition, key num-bers cannot be provided by Hyundai for secu-rity reasons.
If you need additional keys or if you should lose
your keys, your authorized Hyundai dealer canmake new keys.
B885C02A-GAT
Key Numbers
Key Numbers Key Numbers
Key Numbers
Key Numbers
B885C01B
All of the locks fitted to the vehicle are operated
by the same key. However, since it is possible to lock the doors without the use of the key,care should be exercised to ensure that the keydoes not become locked inside the vehicle bymistake. If your vehicle is equipped with Theft-alarm system, the master keys with the function oftransmitter will be provided. (E.C only)
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If you make your own duplicate key, you will
If you make your own duplicate key, you will If you make your own duplicate key, you will
If you make your own duplicate key, you will
If you make your own duplicate key, you will not be able to cancel the system or start the
not be able to cancel the system or start the not be able to cancel the system or start the
not be able to cancel the system or start the
not be able to cancel the system or start the
engine.
engine. engine.
engine.
engine.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
oo
oo
o
The password should be recorded and
The password should be recorded and The password should be recorded and
The password should be recorded and
The password should be recorded and
kept in a safe place in case the need to
kept in a safe place in case the need to kept in a safe place in case the need to
kept in a safe place in case the need to
kept in a safe place in case the need to
order further keys arises.
order further keys arises. order further keys arises.
order further keys arises.
order further keys arises.
oo
oo
o
If you forget the password, consult your
If you forget the password, consult your If you forget the password, consult your
If you forget the password, consult your
If you forget the password, consult your
authorized Hyundai dealer.
authorized Hyundai dealer. authorized Hyundai dealer.
authorized Hyundai dealer.
authorized Hyundai dealer. Without Theft-alarm system
The vehicle key number is recorded upon a metal tag attached to the keys when the vehicleis first delivered to you. The key number should be recorded and kept in a safe place in case the need to order furtherkeys arises. New keys are available from any
B885C02P
With Theft-alarm system

BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
1-8
B120A01P-GAG
Whenever a front door is opened, the ignition switch will illuminate for your convenience. The light will go off 10 seconds after closing the door or when the ignition switch is turned on.
B120A01P-GAT
ILLUMINATED IGNITION SWITCH
ILLUMINATED IGNITION SWITCH ILLUMINATED IGNITION SWITCH
ILLUMINATED IGNITION SWITCH
ILLUMINATED IGNITION SWITCH
(If installed)
(If installed) (If installed)
(If installed)
(If installed) B040A01A-AAT
DOOR LOCKS
DOOR LOCKS DOOR LOCKS
DOOR LOCKS
DOOR LOCKS
WARNING:
WARNING: WARNING:
WARNING:
WARNING:
oo
oo
o Unlocked doors can be dangerous. Be-
Unlocked doors can be dangerous. Be- Unlocked doors can be dangerous. Be-
Unlocked doors can be dangerous. Be-
Unlocked doors can be dangerous. Be-
fore you drive away (especially if there
fore you drive away (especially if there fore you drive away (especially if there
fore you drive away (especially if there
fore you drive away (especially if there
are children in the car), be sure that all
are children in the car), be sure that all are children in the car), be sure that all
are children in the car), be sure that all
are children in the car), be sure that all
the doors are securely closed and locked
the doors are securely closed and locked the doors are securely closed and locked
the doors are securely closed and locked
the doors are securely closed and locked
so that the doors cannot be inadvertently
so that the doors cannot be inadvertently so that the doors cannot be inadvertently
so that the doors cannot be inadvertently
so that the doors cannot be inadvertently
opened from the inside. This helps as-
opened from the inside. This helps as- opened from the inside. This helps as-
opened from the inside. This helps as-
opened from the inside. This helps as-
sure that doors will not be opened acci-
sure that doors will not be opened acci- sure that doors will not be opened acci-
sure that doors will not be opened acci-
sure that doors will not be opened acci-
dentally.
dentally. dentally.
dentally.
dentally.
The following procedure is how to start the
engine with the function of the limp home. (0, 1, 2, 3 as a sample password).
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
You can get the limp home password when
You can get the limp home password when You can get the limp home password when
You can get the limp home password when
You can get the limp home password when the vehicle is first delivered to you. If you do
the vehicle is first delivered to you. If you do the vehicle is first delivered to you. If you do
the vehicle is first delivered to you. If you do
the vehicle is first delivered to you. If you do
not have the password, consult your autho-
not have the password, consult your autho- not have the password, consult your autho-
not have the password, consult your autho-
not have the password, consult your autho-
rized Hyundai dealer.
rized Hyundai dealer. rized Hyundai dealer.
rized Hyundai dealer.
rized Hyundai dealer.
1. To set the password you may turn the igni-
tion key "ON" and then turn it "OFF" accord- ing to the digit numbers, then the immobi-lizer indicator will blink along with the opera-tion of the ignition key. For example, turn theignition key once for digit number "1", andtwice for "2", and so on. However, for thedigit number "0", you must turn the ignitionkey for 10 times.
2. Wait for 3~10 seconds.
3. You may set the remaining number of digits by following the same procedures 1 and 2.
4. If all of four digits have been tried success- fully, turn the ignition key "ON" and check that the immobilizer indicator illuminates.From this time, you have to start your enginewithin 30 seconds. If you start your engineafter 30 seconds, your engine will not start. NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the engine dies while driving after limp
If the engine dies while driving after limp If the engine dies while driving after limp
If the engine dies while driving after limp
If the engine dies while driving after limp
home procedure, you can start your engine
home procedure, you can start your engine home procedure, you can start your engine
home procedure, you can start your engine
home procedure, you can start your engine
within 8 seconds without limp home proce-
within 8 seconds without limp home proce- within 8 seconds without limp home proce-
within 8 seconds without limp home proce-
within 8 seconds without limp home proce-
dure again.
dure again. dure again.
dure again.
dure again.
5. If the immobilizer indicator blinks for five seconds, you have to try the limp homeprocedure again from the beginning.
After doing the limp home procedure, you haveto consult with your authorized Hyundai dealeras soon as possible.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
oo
oo
o If you fail to try the limp home procedure
If you fail to try the limp home procedure If you fail to try the limp home procedure
If you fail to try the limp home procedure
If you fail to try the limp home procedure
with the sequence of three times, you
with the sequence of three times, you with the sequence of three times, you
with the sequence of three times, you
with the sequence of three times, you
have to wait for about one hour to do the
have to wait for about one hour to do the have to wait for about one hour to do the
have to wait for about one hour to do the
have to wait for about one hour to do the
limp home procedure again.
limp home procedure again. limp home procedure again.
limp home procedure again.
limp home procedure again.
oo
oo
o If you cannot start your engine in spite of
If you cannot start your engine in spite of If you cannot start your engine in spite of
If you cannot start your engine in spite of
If you cannot start your engine in spite of
limp home procedure, have your vehicle
limp home procedure, have your vehicle limp home procedure, have your vehicle
limp home procedure, have your vehicle
limp home procedure, have your vehicle
towed by an authorized Hyundai dealer.
towed by an authorized Hyundai dealer. towed by an authorized Hyundai dealer.
towed by an authorized Hyundai dealer.
towed by an authorized Hyundai dealer.

BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
1-10 B070C01FC-GAT
Alarm Stage
Alarm Stage Alarm Stage
Alarm Stage
Alarm Stage
B070C02P
B070A01P-GAT
THEFT-ALARM SYSTEM
THEFT-ALARM SYSTEM THEFT-ALARM SYSTEM
THEFT-ALARM SYSTEM
THEFT-ALARM SYSTEM
(Minibus only) (If installed)
(Minibus only) (If installed) (Minibus only) (If installed)
(Minibus only) (If installed)
(Minibus only) (If installed) This system is designed to provide protection
from unauthorized entry into the car. This sys- tem is operated in three stages: the first is the"Armed" stage, the second is the "Alarm" stage,and the third is the "Disarmed" stage. If trig-gered, the system provides an audible alarmwith blinking of the turn signal light. B150B01P-GAT
CENTRAL DOOR LOCKS
CENTRAL DOOR LOCKS CENTRAL DOOR LOCKS
CENTRAL DOOR LOCKS
CENTRAL DOOR LOCKS
(For Truck) (If installed)
(For Truck) (If installed) (For Truck) (If installed)
(For Truck) (If installed)
(For Truck) (If installed) The central door locking system is located on the driver's door lock button. It is operated bydepressing the door lock button. If the front dooris open when the button is depressed, the doorwill lock when closed.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
When the front door lock button is de-
When the front door lock button is de- When the front door lock button is de-
When the front door lock button is de-
When the front door lock button is de-
pressed, the front doors will lock. When the
pressed, the front doors will lock. When the pressed, the front doors will lock. When the
pressed, the front doors will lock. When the
pressed, the front doors will lock. When the
front door lock button is pulled up, the front
front door lock button is pulled up, the front front door lock button is pulled up, the front
front door lock button is pulled up, the front
front door lock button is pulled up, the front
doors will unlock.
doors will unlock. doors will unlock.
doors will unlock.
doors will unlock. B070B01O-AAT
Armed Stage
Armed Stage Armed Stage
Armed Stage
Armed Stage CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Do not arm the system until all passengers
Do not arm the system until all passengers Do not arm the system until all passengers
Do not arm the system until all passengers
Do not arm the system until all passengers
have left the car. If the system is armed
have left the car. If the system is armed have left the car. If the system is armed
have left the car. If the system is armed
have left the car. If the system is armed
while a passenger(s) remains in the car, the
while a passenger(s) remains in the car, the while a passenger(s) remains in the car, the
while a passenger(s) remains in the car, the
while a passenger(s) remains in the car, the
alarm may be activated when the remaining
alarm may be activated when the remaining alarm may be activated when the remaining
alarm may be activated when the remaining
alarm may be activated when the remaining
passenger(s) leaves the car.
passenger(s) leaves the car. passenger(s) leaves the car.
passenger(s) leaves the car.
passenger(s) leaves the car.
B070B02P
LOCK
UNLOCK
Park the car and stop the engine. Arm the system as described below.
1) Remove the ignition key from the ignition switch.
2) Make sure that the engine hood and tail gate are locked.
3) Lock the doors using the transmitter of the keyless entry system.
After completion of the steps above, the turnsignal light will blink once to indicate that thesystem is armed.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
1)1)
1)1)
1) If any door, tail gate or engine hood
If any door, tail gate or engine hood If any door, tail gate or engine hood
If any door, tail gate or engine hood
If any door, tail gate or engine hood
remains open, the system will not be
remains open, the system will not be remains open, the system will not be
remains open, the system will not be
remains open, the system will not be
armed.
armed. armed.
armed.
armed.
2)2)
2)2)
2) If this happens, rearm the system as
If this happens, rearm the system as If this happens, rearm the system as
If this happens, rearm the system as
If this happens, rearm the system as
described above.
described above. described above.
described above.
described above. The alarm will be activated if any of the follow- ing occurs while the car is parked and thesystem is armed.
1) A front or rear door is opened without using the transmitter.
2) The tail gate is opened without using the transmitter.
3) The engine hood is opened.
The alarming horn will sound and the turn signallight will blink continuously for 27 seconds (E.C

1-11
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
B070D02O-AAT
Disarmed Stage
Disarmed Stage Disarmed Stage
Disarmed Stage
Disarmed Stage The system will be disarmed when the driver’s
or passenger’s door is unlocked by depressing the "UNLOCK" button on the transmitter.
After completion of the step above, the turn
signal light will blink twice to indicate that thesystem is disarmed.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
Once the system has been disarmed, it can
Once the system has been disarmed, it can Once the system has been disarmed, it can
Once the system has been disarmed, it can
Once the system has been disarmed, it can not be rearmed except by repeating the
not be rearmed except by repeating the not be rearmed except by repeating the
not be rearmed except by repeating the
not be rearmed except by repeating the
arming procedures.
arming procedures. arming procedures.
arming procedures.
arming procedures.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Only the transmitter can disarm the armed
Only the transmitter can disarm the armed Only the transmitter can disarm the armed
Only the transmitter can disarm the armed
Only the transmitter can disarm the armedstage. If the transmitter does not disarm the
stage. If the transmitter does not disarm the stage. If the transmitter does not disarm the
stage. If the transmitter does not disarm the
stage. If the transmitter does not disarm the
system, it is necessary to take the following
system, it is necessary to take the following system, it is necessary to take the following
system, it is necessary to take the following
system, it is necessary to take the following
steps;
steps; steps;
steps;
steps;
1.1.
1.1.
1.
Unlock the door with the key, which will
Unlock the door with the key, which will Unlock the door with the key, which will
Unlock the door with the key, which will
Unlock the door with the key, which will
cause, the alarm to be activated.
cause, the alarm to be activated. cause, the alarm to be activated.
cause, the alarm to be activated.
cause, the alarm to be activated.
2.2.
2.2.
2. Insert the key in the ignition key cylinder
Insert the key in the ignition key cylinder Insert the key in the ignition key cylinder
Insert the key in the ignition key cylinder
Insert the key in the ignition key cylinder
and turn the ignition key to "ON" posi-
and turn the ignition key to "ON" posi- and turn the ignition key to "ON" posi-
and turn the ignition key to "ON" posi-
and turn the ignition key to "ON" posi-
tion.
tion. tion.
tion.
tion. B070F01A-GAT
Keyless Entry System (If installed)
Keyless Entry System (If installed) Keyless Entry System (If installed)
Keyless Entry System (If installed)
Keyless Entry System (If installed)
Locking doors
Locking doors Locking doors
Locking doors
Locking doors
1. Close all doors.
2. Push the "LOCK" button on the transmitter.
3. At the same time all doors lock, the turn signal lamp will blink once to indicate thatthe system is armed.
Unlocking doors
Unlocking doors Unlocking doors
Unlocking doors
Unlocking doors
1. Push the "UNLOCK" button on the transmit- ter.
2. At the same time all doors unlock, the turn signal lamp will blink twice to indicate thatthe system is disarmed.
only/ Except E.C 3 times). To turn off thesystem, unlock the door or tail gate with thetransmitter.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Avoid trying to start the engine while the
Avoid trying to start the engine while the Avoid trying to start the engine while the
Avoid trying to start the engine while the
Avoid trying to start the engine while the
system is armed.
system is armed. system is armed.
system is armed.
system is armed.
2. Remove the old battery from the case andnote the polarity. Make sure the polarity ofthe new battery is the same(+side facingdown), then insert it in the transmitter.
B070E02P
B070E02HP-GAT
Replacing the battery
Replacing the battery Replacing the battery
Replacing the battery
Replacing the battery When the transmitter's battery begins to get
weak, it may take several pushes on the button to lock or unlock the doors, and the LED will notlight. Replace the battery as soon as possible.
Battery type : CR2032 1. Separate the case with a phillips screw-
driver.
B070E01P
3.3.
3.3.
3. Wait for 30 seconds.
Wait for 30 seconds. Wait for 30 seconds.
Wait for 30 seconds.
Wait for 30 seconds.
After completing the steps above, the sys-
After completing the steps above, the sys- After completing the steps above, the sys-
After completing the steps above, the sys-
After completing the steps above, the sys- tem will be disarmed.
tem will be disarmed. tem will be disarmed.
tem will be disarmed.
tem will be disarmed. Replacement instructions:

BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
1-12
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Make sure that the support rod has been
Make sure that the support rod has been Make sure that the support rod has been
Make sure that the support rod has been
Make sure that the support rod has been released prior to closing
released prior to closing released prior to closing
released prior to closing
released prior to closing the hood. Always
the hood. Always the hood. Always
the hood. Always
the hood. Always
double check to be sure that the hood is
double check to be sure that the hood is double check to be sure that the hood is
double check to be sure that the hood is
double check to be sure that the hood is
firmly latched before
firmly latched before firmly latched before
firmly latched before
firmly latched before driving away. If it is not
driving away. If it is not driving away. If it is not
driving away. If it is not
driving away. If it is not
latched, the hood could fly open while the
latched, the hood could fly open while the latched, the hood could fly open while the
latched, the hood could fly open while the
latched, the hood could fly open while the
vehicle
vehicle vehicle
vehicle
vehicle
is being driven, causing a total loss
is being driven, causing a total loss is being driven, causing a total loss
is being driven, causing a total loss
is being driven, causing a total loss
of visibility, which might result in
of visibility, which might result in of visibility, which might result in
of visibility, which might result in
of visibility, which might result in
an acci-
an acci- an acci-
an acci-
an acci-
dent. The support rod must be inserted
dent. The support rod must be inserted dent. The support rod must be inserted
dent. The support rod must be inserted
dent. The support rod must be inserted
completely into the hole provided
completely into the hole provided completely into the hole provided
completely into the hole provided
completely into the hole provided in the
in the in the
in the
in the
hood whenever you inspect the engine com-
hood whenever you inspect the engine com- hood whenever you inspect the engine com-
hood whenever you inspect the engine com-
hood whenever you inspect the engine com-
partment. This will prevent
partment. This will prevent partment. This will prevent
partment. This will prevent
partment. This will prevent the hood from
the hood from the hood from
the hood from
the hood from
falling and possibly injuring you. Do not
falling and possibly injuring you. Do not falling and possibly injuring you. Do not
falling and possibly injuring you. Do not
falling and possibly injuring you. Do not
move the vehicle with
move the vehicle with move the vehicle with
move the vehicle with
move the vehicle with the hood in the raised
the hood in the raised the hood in the raised
the hood in the raised
the hood in the raised
position, as vision is obstructed and the
position, as vision is obstructed and the position, as vision is obstructed and the
position, as vision is obstructed and the
position, as vision is obstructed and the
hood could
hood could hood could
hood could
hood could
fall or be damaged.
fall or be damaged. fall or be damaged.
fall or be damaged.
fall or be damaged.
B570A02P
B570A01F-GAT
HOOD RELEASE
HOOD RELEASE HOOD RELEASE
HOOD RELEASE
HOOD RELEASE
B570A01P-1
1. Pull the release knob to unlatch the hood.
2. Press the safety catch lever up side and lift the hood.
3. Hold the hood open with the support rod.
Before closing the hood, return the support rod to its clip to prevent it from rattling. Lower the
hood until it is about 30 cm (1 ft.) above theclosed position and let it drop. Make sure that itlocks into place.
B160A02P-GAT
"C"C
"C"C
"C HILD-PROTECTION" SLIDE DOOR
HILD-PROTECTION" SLIDE DOOR HILD-PROTECTION" SLIDE DOOR
HILD-PROTECTION" SLIDE DOOR
HILD-PROTECTION" SLIDE DOOR
(Minibus,
(Minibus, (Minibus,
(Minibus,
(Minibus, VV
VV
V an)an)
an)an)
an)
GT10190A-1
Lever
When the slide door is closed with the "child-
protection" lever in the " " position, it cannot be opened by using the inner handle. Use theouter handle to open the door.
If adults are to sit in the second seat, release
the child protection lock. When this is done, thelever will be in the " " position.
B160B01P-GAT CARRYING CHILDREN
CARRYING CHILDREN CARRYING CHILDREN
CARRYING CHILDREN
CARRYING CHILDREN
(1) If a child is left in the vehicle alone, always be sure to turn off the ignition and removethe key.
(2) If a child is seated alone in the second seat, use the child-protection system.