2003 FORD MUSTANG oil

10. Remove the mounting bolts and the vacuum accessory bracket.
11. Disconnect the camshaft position (CMP) sensor electrical connector.
12. Remove the fasteners and position the power steering reservoir aside.
13. Remove the bolt and position the oil level indicator tube aside. Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

16. Inspect the valve cover spark plug hole gaskets. Install new gaskets, if necessary. Make sure
the gaskets are correctly seated on the valve cover.
17. NOTE: If the valve cover is not secured within four minutes, the sealant must be removed and
the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of
wetness, or four minutes, whichever is longer. Failure to follow this procedure can result in
future oil leakage.
Apply a bead of silicone gasket and sealant in two places where indicated.
18. To install, reverse the removal procedure. zTighten the valve cover in the sequence shown. Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Crankshaft Front Seal
Removal 1. Remove the crankshaft pulley. For additional information, refer to Crankshaft Pulley in this
section. 2. Using the special tool, remove the crankshaft front seal. SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Special Tool(s)
Installer, Front Cover Oil Seal
303-
335 (T88T-6701- A) Remover, Crankshaft Front Oil
Seal
303-
107 (T74P-6700- A) Installer, Crankshaft Front Oil
Seal
303-
635 Installer, Crankshaft Vibration
Damper
303-
102 (T74P-6316- B)
Material Item Specification
SAE 5W-
20 Premium Synthetic
Blend Engine Oil
XO- 5W20- QSP or equivalent WSS-
M2C153-
H Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Installation
1. Lubricate the engine front cover and the crankshaft front seal inner lip with clean engine oil.
2. Using the special tool, install the crankshaft front seal.
3. Install the crankshaft pulley. For additional information, refer to Crankshaft Pulley in this section.
4. Install the auxiliary crankshaft pulley. For additional information, refer to Crankshaft Pulley —
Auxiliary in this section. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Engine Front Cover
Removal 1. Remove the crankshaft front seal. For additional information, refer to Crankshaft Front Seal in
this section.
2. Remove the oil filter adapter. For additional information, refer to Oil Filter Adapter in this section.
3. Remove the three bolts shown. Loosen the fourth bolt (hidden below the power steering tube) and position the power steering pump aside.
4. Remove the A/C muffler bracket nut.
5. Remove the bolts and position the A/C compressor aside.
SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA or equivalent WSE-
M5B392- A Silicone Gasket and Sealant
F7AZ-
19554- EA or equivalent WSE-
M4G323-
A4 SAE 5W-
20 Premium Synthetic
Engine Oil
XO- 5W20- QSP or equivalent WSS-
M2C153-
H Klj . 1 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

29.
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other
abrasive means to clean the sealing surfaces. These tools cause scratches and gouges
which make leak paths. Use a plastic scraping tool to remove all traces of old sealant.
Remove and discard the gasket, clean and inspect the sealing surfaces.
Installation 1. NOTE: If the valve cover is not secured within four minutes, the sealant must be removed and
the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of
wetness, or four minutes, whichever is longer. Failure to follow this procedure can result in
future oil leakage.
Apply silicone gasket and sealant in the locations shown.
2. Install the engine front cover and tighten the fasteners in the sequence shown, to 25 Nm (18 lb- in). Klj . 7 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

26. Position the power steering pump and install the bolts.
27. Install the oil filter adapter. For additional information, refer to
Oil Filter Adapter in this section.
28. Install the crankshaft front seal. For additional information, refer to Crankshaft Front Seal in this
section.
29. Fill and bleed the engine coolant and the supercharger coolant. For additional information, refer to Section 303 - 03A and
Section 303 - 03B .
30. Fill the crankcase with clean engine oil. Klj . 14 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Camshaft
Removal 1. Remove the roller followers. For additional information, refer to Camshaft Roller Follower in this
section.
2. Remove the LH timing chain (6268) for the LH side and both timing chains for the RH side. For additional information, refer to Timing Drive Components in this section.
3. Install the special tool.
4. Remove the exhaust camshaft sprocket (6250) and the intake camshaft bolt, washer and spacer.
SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Special Tool(s)
Holding Tool, Camshaft
303-
446 (T93P-6256- AHR)
Material Item Specification
Super Premium SAE 5W-20
Engine Oil
XO- 5W20- QSP or equivalent WSS-
M2C153-
H Klj . 1 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...