2003 FORD MUSTANG oil

65.
NOTE: Only three bolts are required for installation.
Install the power steering pump. zPosition the power steering pump.
z Install the bolts.
66. Lubricate the O- ring seal with PAG compressor oil, YN-12C, F7AZ-19589- DA or equivalent
meeting Ford specification WSH- M1C231-B.
Install the A/C compressor.
67. Install the oil filter adapter. Klj . 25 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Apply an eight millimeter bead of silicone gasket and sealant at the intersection of the engine
front cover and the cylinder head.
71. NOTE: RH valve cover shown, LH similar.
Install the valve covers.
72. NOTE: Lubricate the O- ring seal with clean engine oil.
Install a new O- ring.
73. Install the tube. Klj . 27 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

82. Install the generator support brace.
83. Install the accessory drive belt. For additional information, refer to
Section 303 - 05 .
84. Install the radio interference capacitors.
85. Install the ignition coils and bolts. Klj . 30 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

96. Install the RH and LH special tools.
97. Using the special tool, remove the engine from the stand.
98. Using the special tool, install the crankshaft rear main seal.
zLubricate the oil seal using clean engine oil. 5 — To ignition coils (8)
6 — To engine coolant temperature sensor
7 — To throttle position sensor
8 — To idle air control valve
9 — To EGR vacuum regulator
10 — To differential pressure feedback EGR
11 — To fuel pressure regulator
12 — Fuel injection ground
13 — To generator
14 — To camshaft position sensor
15 — To body
16 — To heated oxygen sensor (2)
17 — Engine bulkhead connector
18 — To low coolant sensor
19 — To body
20 — To power distribution box
21 — To body Klj . 34 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

99. Using the special tools, install the crankshaft rear oil slinger.
100. Install the separator plate.
101. Install the flywheel. Klj . 35 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

INSTALLATION
Cylinder Heads
SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Special Tool(s)
Installer, Crankshaft Vibration
Damper
303-
102 (T74P-6316- B) Installer, Front Cover Oil Seal
303-
335 (T88T-6701- A) Holding Tool, Crankshaft
303-
448 (T93P-6303- A) Spreader Bar
303-
D089 (D93P-6001- A3) Lifting Bracket Set, Engine
303-
D074 (D91P-6001- A) Strap Wrench
303-
D055 (D85L-6000- A) or
equivalent Compressor, Valve Spring
303-
567 (T97P-6565- AH) Compressor Spacer, Valve
Spring Klj . 1 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Both cylinder heads
1. CAUTION: The gasket sealing surfaces on the cylinder head and cylinder block
must be clean. For additional information, refer to Cylinder Heads in the Removal portion
of this section.
CAUTION: The use of sealing aids (aviation cement, copper spray and glue) is not
permitted. The gasket must be installed dry.
CAUTION: The new gasket has a film coating which is crucial to the gasket's ability
to seal correctly. Do not scratch the gasket.
NOTE: RH head gasket shown; LH head gasket similar.
Install the head gasket over the dowel pins. 303-
382 (T91P-6565- AH) Remover/Installer, Cylinder
Head
303-
572 (T97T-6000- A)
Material Item Specification
Motorcraft Silicone Gasket
Remover
ZC-
30 —
Motorcraft Metal Surface Prep
ZC-
31 —
Hydraulic Chain Tensioner
Retaining Clip
1L3Z-6P250-
AA —
Silicone Gasket and Sealant
F7AZ-
19554- EA or equivalent WSE-
M4G323-
A4 Super Premium SAE 5W-20
Engine Oil
XO- 5W20- QSP or equivalent WSS-
M2C153-
H Klj . 2 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2.
CAUTION: Cylinder head machining or milling is not authorized by the Ford Motor
Company. Cylinder head flatness must be within 0.0254 mm (0.001 in) across a 38.1 mm
(1.5 in) square area.
CAUTION: The use of sealing aids (aviation cement, copper spray and glue) is not
permitted. The gasket must be installed dry.
CAUTION: Do not allow the dowels to scratch the sealing surface of the cylinder
head during cylinder head installation.
NOTE: The new cylinder head bolts must be lightly oiled with a rag, and allowed to drain for a
few minutes prior to installation.
NOTE: RH head gasket shown; LH head gasket similar.
Install the cylinder head on the dowels and the head gasket. Loosely install new bolts.
NOTE: Position the cylinder head(s) over the dowels on the head gasket(s).
3. NOTE: LH shown, RH similar.
Tighten the bolts in six stages in the sequence shown. zStage 1: Tighten to 40 Nm (30 lb- ft).
z Stage 2: Tighten an additional 90 degrees.
z Stage 3: Loosen the bolts a minimum of one full turn.
z Stage 4: Tighten to 40 Nm (30 lb- ft).
z Stage 5: Tighten an additional 90 degrees.
z Stage 6: Tighten an additional 90 degrees. Klj . 3 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...