2003 FORD MUSTANG oil

z
The inner rotor is piloted on the crankshaft post and is driven through flats on the crankshaft.
z System pressure is limited by an integral, internally- vented relief valve which directs the
bypassed oil back to the inlet side of the oil pump.
z Oil pump displacement has been selected to provide adequate volume to ensure correct oil
pressure both at hot idle and maximum speed.
z The relief valve calibration protects the system from excessive pressure during high viscosity
conditions.
z The relief valve is designed to provide adequate connecting rod bearing lubrication under high-
temperature and high- speed conditions.
Cooling System
The engine cooling system includes the following:
zradiator
z water pump
z the electric cooling fan motor and fan blade, activated by the variable control module
z the degas bottle, which aids in maintaining the correct volume of engine coolant
z water thermostat
z upper radiator hose
z lower radiator hose
z heater water hoses
Drive Belt System
The 4.6L (4V) DOHC engine is equipped with a serpentine drive belt. To ensure maximum life, a
replacement drive belt should be of the same type as originally installed.
zThe accessories mounted on the front of the engine are belt- driven by the crankshaft.
z The serpentine drive belt is routed over each accessory pulley, driven by the crankshaft pulley
bolted to the crankshaft.
For service procedures, including tensioning, refer to Section 303 - 05 . Klj . 3 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8 6B277 Camshaft bearing cap
9 — Bolt (24 req'd)
10 6A271 Camshaft
11 6529 Roller follower (8 req'd)
12 6C501 Hydraulic lash adjuster
13 6065 Bolt (20 req'd)
14 6A273 Camshaft
15 6B278 Camshaft bearing cap (2 req'd)
16 9448 Exhaust manifold gasket
17 9F485 EGR valve tube to manifold connector
18 W701706 Nut (8 req'd)
19 9431 Exhaust manifold
20 6C324 PCV tube
21 6A505 Valve cover
22 N808199 Bolt (20 req'd)
23 6766 Oil filler cap
24 12A366 Ignition coils
25 6P068 Ignition coil cover
26 N807309 Bolt (4 req'd)
27 6050 Cylinder head Klj . 10 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Item Part Number Description
1 8555 Water bypass tube
2 6750 Oil level indicator
3 6754 Oil level indicator tube
4 N806155 Bolt
5 6C358 Bolt (10 req'd)
6 6714 Oil bypass filter
7 6A642 Oil cooler
8 N806156 Bolt (4 req'd) Klj . 13 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9 9278 Oil pressure sender
10 6884 Oil filter adapter
11 6A636 Oil filter adapter gasket
12 N620482 Dowel
13 87836 Plug
Item Part Number Description
1 N807198 Dowel pin (2 req'd)
2 N807309 Bolt
3 N807959 Bolt
4 18663 Heater water hose
5 W500110 Bolt (2 req'd)
6 12A699 Knock sensor (2 req'd)
7 N807309 Bolt (2 req'd)
8 18696 Heater water hose
9 7120 Pilot bearing
10 6K318 Crankshaft rear retainer
11 N806155 Bolt (6 req'd)
12 6310 Crankshaft oil slinger
13 6375 Flywheel
14 N808139 Bolt (8 req'd)
15 7550 Clutch disc
16 7563 Clutch pressure plate
17 N808969 Bolt (6 req'd)
18 6701 Crankshaft rear oil seal Klj . 14 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8 6K258 Stud (4 req'd)
9 6687 Oil pan baffle
10 N806180 Spacer
11 N605904 Bolt
12 6710 Oil pan gasket
13 6675 Oil pan
14 W701240 Bolt (16 req'd)
15 6622 Oil pump screen pickup and tube
16 N806155 Bolt (2 req'd)
17 N811280 Spacer (3 req'd)
18 6345 Bolt (6 req'd)
19 6C360 Main bearing cap adjusting screw (10 req'd)
20 6A338 Crankshaft main bearing (4 req'd)
21 N806201 Woodruff key
22 6621 Oil pump
23 N806183 Bolt (4 req'd)
24 6333 Crankshaft main bearing
25 8501 Water pump Klj . 16 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Valve Cover RH
Removal and Installation 1. Remove the RH ignition coils. For additional information, refer to Section 303 - 07C .
2. Remove the A/C condenser to evaporator tube. For additional information, refer to Section 412 -
03 .
3. Remove the A/C manifold and tube assembly. For additional information, refer to Section 412 -
03 .
4. Disconnect the throttle position (TP) sensor and the idle air control (IAC) valve electrical connectors.
5. Disconnect the vacuum hose.
6. Disconnect the fuel hose spring lock coupling. For additional information, refer to Section 310 -
00 .
SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Silicone Gasket and Sealant
F7AZ-
19554- EA WSE-
M4G323- A4 Metal Surface Cleaner
F4AZ-
19A536- RA WSE-
M5B392- A Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11. Remove the RH valve cover.
z CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or
other abrasive means to clean the sealing surfaces. These tools cause scratches
and gouges which make leak paths. Use a plastic scraping tool to remove all
traces of old sealant.
Remove and discard the gasket, clean and inspect the sealing surfaces.
12. Inspect the valve cover spark plug hole gaskets. Install new gaskets, if necessary. Make sure the gaskets are correctly seated on the valve cover.
13. NOTE: If the valve cover is not secured within four minutes, the sealant must be removed and
the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of
wetness, or four minutes, whichever is longer. Failure to follow this procedure can result in
future oil leakage.
Apply a bead of silicone gasket and sealant in two places where indicated. Klj . 3 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Valve Cover LH
Removal and Installation 1. Remove the Hydro Boost brake booster. For additional information, refer to Section 206 - 07 .
2. Remove the LH ignition coils. For additional information, refer to Section 303 - 07C .
3. Disconnect the engine coolant temperature (ECT) sensor and unclip the wiring harness from the stud.
4. Unclip the wiring harness from the power steering bracket.
5. Disconnect the electrical connectors from the fuel pulse damper, EGR vacuum regulator solenoid, supercharger bypass vacuum solenoid, and the differential pressure feedback EGR
system.
SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Silicone Gasket and Sealant
F7AZ-
19554- EA WSE-
M4G323- A4 Metal Surface Cleaner
F4AZ-
19A536- RA WSE-
M5B392- A Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...