2003 FORD MUSTANG clip

6. Remove the front seat backrest pad adjusting pump (65530).
1. Disconnect the electrical connector.
2. Disconnect the power lumbar support air hose.
Vehicles with power bolster and lumbar 7. Remove the driver seat backrest latch. For additional information, refer to Latch — Front Seat
Backrest in this section.
8. Remove the pivot bolt and seat backrest. zDisconnect the power lumbar support air hoses.
9. Release the J- clips. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

9. Disconnect the lumbar and bolster control switches.
All vehicles 10. Remove the J- clips.
11. Remove the hog rings.
12. Remove the front seat cushion cover (62900) from the front seat cushion pad (632A22). Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DISASSEMBLY AND ASSEMBLY
Front Seat Backrest
Disassembly and Assembly
All vehicles
1. Remove the front seat backrest. For additional information, refer to Front Seat Backrest in this
section.
2. Remove the front seat backrest head restraint (611A08).
3. Remove the screws and the safety belt guide.
4. Remove the front seat headrest guide rod sleeve (610A16). 5. Release the J - clip. SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Switch —
Window Regulator Control
Removal
1. CAUTION: Use a shop towel or similar material between the tool and the door trim
panel or damage to the door trim panel may occur.
Position the window regulator switch plate aside. 1. Pull at the service notch.
2. Lift to release the clip at the rear edge.
2. Remove the window regulator control switch. 1. Remove the screws.
2. Disconnect the connectors.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
11: Glass, Frames and Mechanisms 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Rear Window Defrost Switch
Removal and Installation
1. Remove the instrument panel center finish panel. For additional information, refer to Section 501 - 12 .
2. Release the clips and remove the rear window defrost switch.
3. To install, reverse the removal procedure.
SECTION 501-
11: Glass, Frames and Mechanisms 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Coupe
8. Remove the sun visors and clips zRemove the screws.
z Remove the clips.
9. Remove the roof side trim moulding. For additional information, refer to Section 501 - 08 .
10. Lower the front portion of the headliner.
All vehicles 11. Remove the two windshield wiper pivot arms. 1. Raise up on the pivot arms.
2. Release the retainer tabs, and release the windshield wiper pivot arms.
12. Remove the cowl grille weatherstrip. Klj . 3 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

10.
CAUTION: Open a window to prevent the windshield glass from being pushed out
by air pressure when a door is closed.
Using the alignment marks install the windshield glass.
11. After the glass is set, check for water leaks and add urethane adhesive where needed.
12. Install the cowl grille.
13. Install the cowl grille weatherstrip.
14. Install the two windshield wiper pivot arms. zPosition the arms.
z Install the windshield wiper pivot arms.
15. Install the headliner.
Coupe 16. Install the sun visors and clips. Klj . 7 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

25. If equipped, disconnect the shift interlock assembly from the selector lever.
1. Remove the screw.
2. Remove the R- clip.
3. Disconnect the shift interlock cable.
4. Disconnect the shift interlock assembly from the selector lever.
26. Remove the audio unit. For additional information, refer to Section 415 - 01 .
27. If equipped, disconnect the shifter assembly electrical connector.
28. NOTE: This step is being carried out through the audio unit opening.
NOTE: Rotate the temperature control switch to the cool position.
Release the temperature control cable from the blend door.
29. Remove the four center instrument panel support bolts. Klj . 6 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...