2003 FORD MUSTANG clip

REMOVAL AND INSTALLATION
Lamp Assembly —
Fog Lamp (GT)
Removal 1. Raise and support the vehicle.
2. Remove the screw.
3. Partially lower the vehicle and remove the fog lamp assembly. 1. Disconnect the electrical connector.
2. Remove the two screws.
3. Remove the fog lamp assembly and replace the bulb if necessary.
Installation 1. NOTE: Be sure the fascia clip is correctly installed on the bottom side of the fog lamp assembly
bracket.
To install, reverse the removal procedure.
SECTION 417-
01: Exterior Lighting 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lamp Switch —
Brake Pedal Position (BPP)
Removal 1. Disconnect the battery ground cable.
2. Remove the brake pedal position (BPP) switch. 1. Remove the clip.
2. Remove the retainer.
3. Disconnect the electrical connector.
4. Remove the BPP switch.
Installation 1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms
may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven
16 km (10 mi) or more to relearn the strategy.
To install, reverse the removal procedure.
SECTION 417-
01: Exterior Lighting 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Body Sealer Types And Applications
Liquid Butyl Sealer
HB Fuller E709-19554-
B or equivalent meeting Ford Specification ESB-M4G162- A:
z Does not run.
z Is fast drying.
z Remains semi-elastic.
z Can be used for seam sealing on the floorpan, wheelhouse, body rocker panels, door openings,
and drip rails.
Caulking Cord
3M Strip Caulk- Black 051135-08578 or equivalent meeting Ford specification ESB-M4G32- A:
z Is a heavy- bodied, plastic base with a filler.
z Is commonly known as perma-gum.
z Is used on spot- welds holes, around moulding clips, and between surfaces not sealed with a
gasket.
Weatherstrip Adhesive
Weatherstrip and Rubber Adhesive E8AZ-19552- A or equivalent meeting Ford specification ESB-
M2G14- A:
z Is a quick drying, strong adhesive designed to hold weatherstripping onto all body panels and
surrounding metal.
Silicone Lubricant
Silicone Lubricant C0AZ-19553-AA meeting Ford specification ESR- M13P4-A:
z Is used to keep the door and the window weatherstrip pliable and soft.
z Should be applied to the weatherstrip at every lubrication period.
z Makes the door easier to close.
z Retards weatherstrip squeaks.
z Retards weatherstrip wear.
z Helps retain door window alignment by reducing friction between the glass frame and the rubber
weatherstrip.
z Should not be used prior to painting.
SECTION 501-
00: Body System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Trim Panel —
Door
Removal
All vehicles
1. CAUTION: Use a shop towel or similar material between the tool and the front door
trim panel or damage to the front door trim panel may occur.
Position the window regulator switch plate (14527) aside. 1. Pull at the service notch.
2. Lift to release the clip at the rear edge.
2. Remove the window regulator switch plate. 1. Disconnect the power mirror electrical connector.
2. Remove the screws and the window regulator switch plate.
3. Remove the door latch release handle cup (22634).
SECTION 501-
05: Interior Trim and Ornamentation 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

5. Release the clips.
1. Lift up to release the two clips.
2.NOTE: Grasp the roof side moulding and lift up to release the money clip.
Remove the money clip.
6. Remove the upper quarter trim panel. For additional information, refer to Section 501 - 05 .
7. Remove the nuts and the roof side moulding. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Switch —
Exterior Rear View Mirror Control
Removal
1. CAUTION: Use a shop towel or similar material between the tool and the front door
trim panel or damage to the front door trim panel may occur.
Position the window regulator switch plate aside. 1. Pull at service notch.
2. Lift to release the clip at the rear edge.
2. Remove the power exterior rear view mirror control switch. zDisconnect the electrical connector.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lumbar Assembly
Removal and Installation
All vehicles
1. Remove the front seat. For additional information, refer to Seat — Front Power in this section.
2. Release the J- clip.
3. Remove the seat backrest latch handle knob (62762).
4. Pull the seat backrest trim cover up to the top of the seat.
5. Remove the seat backrest foam pad from the seat backrest frame.
Vehicles with standard power lumbar SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lumbar Motor
Removal and Installation
All vehicles
1. Remove the front seat. For additional information, refer to Seat — Front Power in this section.
2. Disconnect the power seat track electrical connector.
3. Remove the four seat track bolts.
Vehicles with standard power lumbar 4. Release the J- clip.
5. Remove the front seat backrest pad adjusting pump screws.
SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...