2003 FORD MUSTANG sensor

10. Disconnect the idle air control (IAC) valve and throttle position (TP) sensor electrical
connectors.
11. Position the RH spark plug wires aside.
12. Position the LH spark plug wires aside. 13. Disconnect the ignition coil and the radio interference capacitor electrical connectors. Klj . 4 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

18.
NOTE: Record the location of the long bolts and the short bolts.
Remove the upper intake manifold and the upper intake manifold gasket.
19. Remove the fuel injection supply manifold and the fuel injectors. For additional information, refer to Section 303 - 04A .
20. Disconnect the cylinder head temperature (CHT) sensor.
21. Disconnect the camshaft position (CMP) sensor electrical connector. Klj . 6 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

22. Disconnect the engine oil pressure sender electrical connector.
23. Remove the pin-
type retainer.
24. Disconnect the crankshaft position (CKP) sensor electrical connector.
25. Remove the engine wiring harness.
26. Remove the stud bolt. Klj . 7 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

47. Remove the RH cylinder head and gasket. Discard the gasket.
48. Remove the camshaft synchronizer. For additional information, refer to
Section 303 - 14 .
49. Remove the bolts and the crankshaft position sensor.
50. Using the special tool, remove the crankshaft front seal.
51. Remove the bolts and the front cover assembly and gasket. Klj . 14 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

52. Remove the camshaft position sensor drive gear.
1. Remove the bolt.
2. Remove the camshaft position sensor drive gear.
53. Compress and install a retaining pin to hold the timing chain tensioner.
54. Remove the camshaft sprocket, the crankshaft sprocket and the timing chain as an assembly.
55. Remove the timing chain tensioner. 1. Remove the bolts.
2. Remove the timing chain tensioner. Klj . 15 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

23. Rotate the crankshaft so the number one piston is at top dead center (TDC) and the key is at
the 12 o'clock position.
24. Turn the camshaft sprocket so that the keyway is on the bottom of the camshaft.
25. Install the timing chain, the camshaft sprocket and the crankshaft sprocket as an assembly.
26. Make sure the timing marks and the keyways are aligned.
27. Install the camshaft position sensor drive gear and retaining bolt. Klj . 9 ba
282003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Nm (21 lb-
ft).
37. NOTE: Lubricate the parts with clean engine oil before assembly.
Using the special tool, install the front crankshaft seal.
38. Install the crankshaft position sensor.
39. Apply a bead of silicone gasket and sealant to the keyway in the crankshaft damper. Using the special tool, position and install the crankshaft damper. Klj . 13 ba
282003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

59. Install the stud bolt.
60. Position the engine wire harness.
61. Connect the crankshaft position sensor electrical connector.
62. Install the pin-
type retainer. Klj . 20 ba
282003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...