2003 FORD MUSTANG sensor

DIAGNOSIS AND TESTING
Anti-
Lock Control — Traction Control
Refer to Wiring Diagrams Cell 42 , Anti-
Lock Brake System for schematic and connector information.
Principles of Operation
The anti- lock-brake control module receives wheel speed readings from each anti- lock brake sensor
and processes this information to determine if an ABS event is necessary. The anti- lock brake sensor
electrically senses each tooth of the anti- lock brake sensor indicators as it passes through the anti- lock
brake sensor's magnetic field.
The anti- lock brake control module continuously monitors and compares the rotational speed of each
wheel and, when it detects an impending wheel lock, modulates brake pressure to the appropriate
brake caliper. This is accomplished by triggering the hydraulic control unit (HCU) to open and close the
appropriate solenoid valves. Once the affected wheel returns to normal speed, the anti- lock brake
control module returns the solenoid valves to their normal position, and normal (base) braking
resumes.
The anti- lock brake control module is self- monitoring. When the ignition switch is turned to the RUN
position, the anti- lock brake control module will do a preliminary electrical check, and at approximately
12 km/h (8 mph) the pump motor is turned on for approximately one half- second. Also during all
phases of operation the anti- lock brake control module (after the vehicle is in motion) checks for
correct operation of the anti- lock brake sensors. Any malfunction of the ABS will cause the ABS to shut
off and ABS warning indicator to illuminate; normal power assisted braking, however, remains.
The ABS control module has the ability to store multiple DTCs in memory.
The traction control system controls wheelspin by modulating the engine torque by communicating to
the powertrain control module (PCM) and by applying, then releasing, the appropriate brake to restore
traction when one or both drive wheels lose traction and begin to spin during acceleration.
The traction control system can be disabled by depressing the traction control switch. The traction
control system will reset and return to normal traction assist when the ignition switch is cycled or when
the traction control switch is depressed again. SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Special Tool(s)
Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F052, or equivalent scan
tool 73 Digital Multimeter or
equivalent
105-
R0051 Klj . 1 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Inspection and Verification
1. Verify the customer concern by operating the system.
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. If the concern remains after the inspection, connect the scan tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from the scan
tool menu. If the scan tool does not communicate with the vehicle: 1. Check that the program card is correctly installed.
2. Check the connections to the vehicle.
3. Check the ignition switch position.
4. If the scan tool still does not communicate with the vehicle, refer to the scan tool manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: 1. CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418-00.
2. NO RESP/NOT EQUIP for the anti- lock brake control module, Go To Pinpoint Test A .
3. SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the anti-lock brake
control module.
6. If the DTCs retrieved are related to the concern, go to the Anti- Lock Brake Control Module
Diagnostic Trouble Code (DTC) Index to continue diagnostics.
7. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnostics.
Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index
NOTE: If a wheel speed signal fault or a pump motor fault is detected, the yellow ABS warning
indicator cannot be reset with the key OFF and key ON method. The vehicle must be driven over 12
km/h (8 mph) for the anti- lock brake control module to do a re- check of the system before the yellow
ABS warning indicator is turned OFF. Visual Inspection Chart Mechanical Electrical
z
Low brake fluid
z Anti- lock brake sensor
z Anti- lock brake sensor indicator
z Base brake system
z Wheel bearings z
Central junction box (CJB) Fuse:
„5 (15A)
„ 15 (10A)
„ 29 (15A)
„ 33 (15A)
„ 35 (15A)
z Battery junction box (BJB) Fuse:
„ABS 1 (50A)
„ ABS 2 (20A)
z Circuitry
z Damaged or corroded connectors
z ABS warning indicator
z Loose grounds Klj . 2 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index
DTC Description Source Action
B1318 Battery Voltage Low ABS/TC Go To Pinpoint Test C .
B1342 ECU Is Defective ABS/TC INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT the
self- test. B1484 Brake Pedal Input Open Circuit ABS/TC Go To Pinpoint Test D .
B1596 Repair Continuous Codes ABS/TC REPAIR the DTCs retrieved.
C1095 ABS Hydraulic Pump Motor Circuit
Failure ABS/TC Go To Pinpoint Test E .
C1145 RF Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1155 LF Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1165 RR Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1175 LR Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1222 Anti-
Lock Brake Sensor Mismatch ABS/TC Go To Pinpoint Test G .
C1233 LF Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1234 RF Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1235 RR Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1236 LR Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1266 ABS Valve Power Relay Circuit
Failure ABS/TC INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT the
self- test. C1805 Mismatched PCM and/or Anti-Lock
Brake Control Module ABS/TC CLEAR the DTCs. RETRIEVE the DTCs. If
DTC C1805 is retrieved, check the PCM
and Anti- Lock Brake Control Module is for
the correct vehicle. INSTALL a new PCM or
anti-lock brake control module as
necessary. CLEAR the DTCs. REPEAT the self-test. U1009 SCP (J1850) Invalid or Missing Data
for Engine Torque ABS/TC CARRY OUT the PCM self-
test. U1027 SCP (J1850) Invalid or Missing Data
for Engine RPM ABS/TC CARRY OUT the PCM self-
test. U1059 SCP (J1850) Invalid or Missing Data
for Transmission/Transaxle/PRNDL ABS/TC CARRY OUT the PCM self-
test. U1083 SCP (J1850) Invalid or Missing Data
for Engine Systems ABS/TC CARRY OUT the PCM self-
test. U1262 SCP (J1850) Communication Bus
Fault ABS/TC REFER to
Section 418 - 00 . Klj . 3 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: DTC C1145 (RF), C1155 (LF), C1165 (RR), C1175
(LR), ANTI-
LOCK BRAKE SENSOR INPUT CIRCUIT FAILURE z
Is the voltage greater than 10 volts? E3 CHECK CIRCUIT 1205 (BK) FOR AN OPEN
z
Measure the resistance between anti- lock brake control module
C141 Pin 12, Circuit 1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
E4 .
No
REPAIR the circuit.
CLEAR the DTCs.
REPEAT the self-
test. E4 CHECK THE PUMP MOTOR FOR OPERATION
z
Disconnect: Pump Motor Connector.
z Connect a 30A fused heavy jumper wire between the positive battery
post and pump motor connector Pin 1 (component side); and
momentarily connect a heavy jumper between negative battery post
and pump motor connector Pin 2 (component side).
z Does the pump motor operate? Yes
INSTALL a new
anti-
lock brake
control module;
REFER to Module .
REPEAT the self-
test.
No
INSTALL a new
HCU; REFER to
Hydraulic Control Unit . CLEAR the
DTCs. REPEAT
the self- test. Test Step Result / Action to Take
F1 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR CIRCUIT FOR SHORT TO POWER z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Key in ON position. Yes
REPAIR the circuit in question.
CLEAR the DTCs. REPEAT the self- Klj . 10 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Measure the voltage between anti- lock brake
control module C141 Pins, harness side and
ground as follows:
z Is any voltage present? DTC Anti-
Lock Brake Control
Module C141 Pin Circuit
C1145
(RF) 4 514
(YE/RD) C1155
(LF) 20 521
(TN/OG) C1165
(RR) 1 494
(TN/LG) C1175
(LR) 22 496 (OG) test.
No
GO to
F2 .
F2 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR CIRCUIT FOR SHORT TO GROUND z
Key in OFF position.
z Measure the resistance between anti- lock brake
control module C141 Pins, harness side and
ground as follows: DTC Anti-
Lock Brake Control
Module C141 Pin Circuit
C1145
(RF) 4 514
(YE/RD) C1155
(LF) 20 521
(TN/OG) C1165
(RR) 1 494
(TN/LG) C1175
(LR) 22 496 (OG) Yes
GO to
F4 .
No
GO to F3 . Klj . 11 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the resistance greater than 10,000 ohms? F3 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR FOR A SHORT TO GROUND z
Disconnect: Suspect Anti- Lock Brake Sensor.
z Measure the resistance between suspect anti- lock
brake sensor Pin 1 (component side) and ground.
z Is the resistance greater than 10,000 ohms? Yes
If RF, REPAIR Circuit 514 (YE/RD)
and Circuit 516 (YE/BK), as
necessary. CLEAR the DTCs.
REPEAT the self-
test. If LF, REPAIR
Circuit 521 (TN/OG) and Circuit 522
(TN/BK), as necessary. CLEAR the
DTCs. REPEAT the self- test. If RR,
REPAIR Circuit 494 (TN/LG) and
Circuit 492 (BN), as necessary.
CLEAR the DTCs. REPEAT the self-
test. If LR, REPAIR Circuit 496 (OG)
and Circuit 499 (GY/BK), as
necessary. CLEAR the DTCs.
REPEAT the self- test.
No
INSTALL a new anti- lock brake
sensor; REFER to Sensor — Front or
Sensor — Rear . CLEAR the DTCs.
REPEAT the self- test. F4 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR CIRCUIT FOR FOR AN OPEN z
Key in OFF position.
z Measure the resistance between anti- lock brake
control module C141 Pins, harness side and
suspect anti- lock brake sensor, harness side as
follows: DTC Anti-Lock
Brake Control Module Anti-Lock
Brake
Sensor Circuit
C1145
(RF) C141 Pin 4 C145 Pin 1 514
(YE/RD) C1145
(RF) C141 Pin 5 C145 Pin 2 516
(YE/BK) C1155
(LF) C141 Pin 20 C144 Pin 1 521
(TN/OG) C1155
(LF) C141 Pin 21 C144 Pin 2 522
(TN/BK) C1165
(RR) C141 Pin 1 C319 Pin 2 494
(TN/LG) C1165 C141 Pin 3 C319 Pin 1 492 (BN) Yes
GO to
F5 .
No
REPAIR the circuit in question.
CLEAR the DTCs. REPEAT the self-
test. Klj . 12 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST G: DTC C1222, ANTI-
LOCK BRAKE SENSOR
MISMATCH z
Are the resistances less than 5 ohms? (RR)
C1175
(LR) C141 Pin 22 C320 Pin 2 496 (OG)
C1175
(LR) C141 Pin 23 C320 Pin 1 499
(GY/BK) F5 CHECK THE ANTI-
LOCK BRAKE SENSOR z
Measure the resistance between suspect anti- lock
brake sensor pin 1 (component side) and suspect
anti- lock brake sensor pin 2 (component side).
z Is the resistance between 1280 and 1920 (front)
or 1830 and 2760 (rear) ohms? Yes
INSTALL a new anti-
lock brake
control module; REFER to Module .
REPEAT the self- test.
No
INSTALL a new anti- lock brake
sensor; REFER to Sensor — Front or
Sensor — Rear . CLEAR the DTCs.
REPEAT the self- test. Test Step Result / Action to Take
G1 CHECK THE VEHICLE
COMPONENTS z
Check for correct wheel and tire
size, front- to-rear and side- to-
side.
z Check for excessive bearing end
play.
z Check the anti- lock brake sensor
indicator for a bent sensor ring or
missing teeth.
z Are the conditions OK? Yes
GO to
G2 .
No
REPAIR as necessary. CLEAR the DTCs. REPEAT
the self- test. G2 TEST DRIVE THE VEHICLE
z
Enter the following diagnostic Yes Klj . 13 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST H: DTC C1233 (LF), C1234 (RF), C1235 (RR), C1236
(LR), ANTI-
LOCK BRAKE SENSOR INPUT SIGNAL MISSING
PINPOINT TEST I: THE YELLOW ABS WARNING INDICATOR DOES
NOT SELF- CHECK mode on the diagnostic tool:
CLEAR the DTCs.
z Key in OFF position.
z Key in ON position.
z Test drive the vehicle over 24
km/h (15 mph).
z Enter the following diagnostic
mode on the diagnostic tool:
Retrieve DTCs.
z Is DTC C1222 retrieved? INSTALL a new anti-
lock brake control module;
REFER to Module . REPEAT the self-
test.
No
If another DTC is retrieved, GO to the Anti- Lock Brake
Control Module Diagnostic Trouble Code (DTC) index.
If no DTCs are retrieved, system is OK. Test Step Result / Action to Take
H1 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR z
Check the suspect anti- lock brake sensor
mounting.
z Check the suspect anti- lock brake sensor for
excessive dirt build up, obstructions, and
damage.
z Is the suspect anti- lock brake sensor and
mounting OK? Yes
GO to
H2 .
No
REPAIR as necessary. CLEAR the
DTCs. REPEAT the self- test. H2 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR INDICATOR z
Check the suspect anti- lock brake sensor
indicator for corrosion, nicks, bridged teeth,
damaged teeth, correct mounting, and
alignment with the anti- lock brake sensor.
z Check the air gap and bearing end play.
z Is the suspect anti- lock brake sensor
indicator OK? Yes
GO to
H3 .
No
INSTALL a new anti- lock brake sensor
indicator; REFER to Sensor Indicator —
Front or
Sensor Indicator — Rear .
CLEAR the DTCs. REPEAT the self- test. H3 CHECK THE ANTI-
LOCK BRAKE SENSOR
OUTPUT z
Key in ON position.
z Enter the following diagnostic mode on the
diagnostic tool: CLEAR the DTCs.
z Key in OFF position.
z Key in ON position.
z Have an assistant monitor the anti- lock brake
control module PIDs LF_WSPD, RF_WSPD,
LR_WSPD, and RR_WSPD while driving at
various speeds.
z NOTE: the vehicle must be driven 16 km (10
miles) during this test step.
z Test drive the vehicle for 16 km (10 miles).
z Are the anti- lock brake control module PIDs
approximately the same at all times? Yes
INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT
the self- test.
No
INSTALL a new anti- lock brake sensor;
REFER to Sensor — Front or
Sensor —
Rear . CLEAR the DTCs. REPEAT the
self- test. Klj . 14 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...