2002 ISUZU AXIOM door lock

8H±16SECURITY AND LOCKS
Keyless Entry System
ID Code Registration
The following procedures are available to register keyless
entry ID codes.
There are four different ID codes which can be registered
for each vehicle.
ID Code New Registration
This procedure erases all registered ID codes and
registers a new ID code instead.
Step
ActionYe sNo
11. Make sure that the all the doors are closed and unlocked.
2. Open the driver's side door.
3. Insert the starter key into the starter switch.
Is the action complete?
Go to Step 2Ð
2Turn the starter switch to ACC position and return it to OFF
position quickly three times.
NOTE: This step must be carried out within five seconds after step
1 is finished.
Is the action complete?
Go to Step 3Go to Step 1
3Close and open the drive's side door quickly two times.
NOTE: This step must be carried out within ten seconds after step
2 is finished.
Is the action complete?
Go to Step 4Go to Step 1
41. Turn the starter switch to ACC position and return it to OFF
position quickly five times.
2. Close and open the driver's side door quickly one time.
NOTE: This step must be carried out within ten seconds after step
3 is finished.
Is the action complete?
Go to Step 5Go to Step 1
5The control unit locks and unlocks the doors one time.
Does the control unit work normally?
Go to Step 6Go to Step 1
6Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 5 is finished.
Is the action complete?
Go to Step 7Go to Step 1
7The control unit locks and unlocks the doors one time.
Does the control unit work normally?
Go to Step 8Go to Step 1
8Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 7 is finished.
Is the action complete?
Go to Step 9Go to Step 1
9If registration succeeds, the control unit locks and unlocks the
doors one time.
If registration fails, the control unit locks and unlocks the doors
three times.
Go to Step 1Go to Step 1

SECURITY AND LOCKS8H±17
ID Code Additional Registration
This procedure additionally registers a new ID code with
holding registered ID codes. If total number of registered
ID codes and newly registered ID code exceed four, the
oldest one is erased.
Step
ActionYe sNo
11. Make sure that the all the doors are closed and unlocked.
2. Open the driver's side door.
3. Insert the starter key into the starter switch.
Is the action complete?
Go to Step 2Ð
2Turn the starter switch to ACC position and return it to OFF
position quickly three times.
NOTE: This step must be carried out within five seconds after step
1 is finished.
Is the action complete?
Go to Step 3Go to Step 1
3Close and open the driver's side door quickly two times.
NOTE: This step must be carried out within ten seconds after step
2 is finished.
Is the action complete?
Go to Step 4Go to Step 1
41. Turn the starter switch to ACC position and return it to OFF
position quickly three times.
2. Close and open the driver's side door quickly one time.
NOTE: This step must be carried out within ten seconds after step
3 is finished.
Is the action complete?
Go to Step 5Go to Step 1
5The control unit locks and unlocks the doors two times.
Does the control unit work normally?
Go to Step 6Go to Step 1
6Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 5 is finished.
Is the action complete?
Go to Step 7Go to Step 1
7The control unit locks and unlocks the doors one time.
Does the control unit work normally?
Go to Step 8Go to Step 1
8Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 7 is finished.
Is the action complete?
Go to Step 9Go to Step 1
9If registration succeeds, the control unit locks and unlocks the
doors one time.
If registration fails, the control unit locks and unlocks the doors
three times.
Go to Step 1Go to Step 1

8H±18SECURITY AND LOCKS
ID Code Check
This procedure checks how many ID codes are
registered.
Step
ActionYe sNo
11. Make sure that the all the doors are closed and unlocked.
2. Open the driver's side door.
3. Insert the starter key into the starter switch.
Is the action complete?
Go to Step 2Ð
2Turn the starter switch to ACC position and return it to OFF
position quickly three times.
NOTE: This step must be carried out within five seconds after step
1 is finished.
Is the action complete?
Go to Step 3Go to Step 1
3Close and open the drive's side door quickly two times.
NOTE: This step must be carried out within ten seconds after step
2 is finished.
Is the action complete?
Go to Step 4Go to Step 1
41. Turn the starter switch to ACC position and return it to OFF
position quickly one time.
2. Close and open the drive's side door quickly one time.
NOTE: This step must be carried out within ten seconds after step
3 is finished.
Is the action complete?
Go to Step 5Go to Step 1
5The control unit locks and unlocks the doors twice as many
registered ID codes.
Go to Step 1Go to Step 1

EXTERIOR/INTERIOR TRIM8J±1
AXIOM
BODY AND ACCESSORIES
EXTERIOR / INTERIOR TRIM
CONTENTS
Service Precaution 8J±2. . . . . . . . . . . . . . . . . . . . . .
Consoles 8J±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consoles and Associated Parts 8J±3. . . . . . . . .
Removal 8J±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Door Trim Panel 8J±4. . . . . . . . . . . . . . . . . . .
Front Door Trim Panel and Associated
Parts 8J±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8J±5. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Trim Panel 8J±6. . . . . . . . . . . . . . . . . . . .
Rear Door Trim Panel and Associated
Parts 8J±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8J±7. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Mirror Assembly 8J±8. . . . . . . . . . . . . . . . . . . .
Removal 8J±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Mirror Assembly 8J±8. . . . . . . . . . . . . . . . . .
Removal 8J±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Trim Panels 8J±9. . . . . . . . . . . . . . . . . . . . . .
Interior Trim Panels and Associated Parts 8J±9
Removal 8J±9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlining 8J±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Location 8J±12. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8J±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overhead Console 8J±14. . . . . . . . . . . . . . . . . . . . . . Parts Location (W/O Sunroof) 8J±14. . . . . . . . . . .
Removal 8J±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Location (W/ Sunroof) 8J±15. . . . . . . . . . . . .
Removal 8J±15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Arch Cover 8J±16. . . . . . . . . . . . . . . . . . . . . . .
Wheel Arch Cover and Associated Parts 8J±16. .
Removal 8J±16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locker Cover 8J±17. . . . . . . . . . . . . . . . . . . . . . . . . . .
Locker Cover and Associated Parts 8J±17. . . . . .
Removal 8J±17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±17. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Filler Door 8J±18. . . . . . . . . . . . . . . . . . . . . . . . .
Parts Location 8J±18. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8J±18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±18. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roof Moulding 8J±19. . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Location 8J±19. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8J±19. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8J±19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Door Mirror System 8J±20. . . . . . . . . . . . . . .
General Description 8J±20. . . . . . . . . . . . . . . . . . . . .
Door Mirror Switch 8J±20. . . . . . . . . . . . . . . . . . . . .
Power Window System 8J±21. . . . . . . . . . . . . . . . . .
General Description 8J±21. . . . . . . . . . . . . . . . . . . . .
Power Window Switch Driver Seat Side 8J±21. .
Power Window Motor 8J±22. . . . . . . . . . . . . . . . . .
Main Data and Specifications 8J±23. . . . . . . . . . . . .

8J±4EXTERIOR/INTERIOR TRIM
7. Remove the CD changer.

Remove the four fixing bolts and the connector.Installation
To install, follow the removal steps in the reverse order.
Front Door Trim Panel
Front Door Trim Panel and Associated Parts
635R200012
Legend
(1) Glass
(2) Glass Run
(3) Door Mirror Assembly
(4) Door Mirror Cover
(5) Tweeter
(6) Speaker Spacer
(7) Speaker Assembly
(8) Inner Waist Seal
(9) Door Trim Panel
(10) Power Window Switch
(11) Inside Lock Bracket(12) Inside Handle
(13) Pull Box
(14) Courtesy Light
(15) Pull Box Bracket
(16) Waterproof Sheet
(17) Front Door Panel
(18) Door Lock Assembly
(19) Door Lock Cylinder
(20) Outside Handle
(21) Power Window Regulator
(22) Outer Waist Seal

8J±6EXTERIOR/INTERIOR TRIM
Rear Door Trim Panel
Rear Door Trim Panel and Associated Parts
655R200009
Legend
(1) Glass Run
(2) Glass
(3) Division Bar
(4) Fix Window Glass
(5) Power Window Regulator
(6) Outside Handle
(7) Door Lock Assembly
(8) Pull Box Bracket
(9) Speaker Spacer
(10) Speaker(11) Pull Box
(12) Door Trim Panel
(13) Courtesy Light
(14) Power Window Switch
(15) Inside Handle
(16) Inside Lock Bracket
(17) Inner Waist Seal
(18) Tweeter
(19) Waterproof Sheet
(20) Outer Waist Seal
(21) Rear Door Panel

SUPPLEMENTAL RESTRAINT SYSTEM 9J±14
deployment procedure until the deployed air bag
assembly is scrapped. Before performing the
procedures, you should be familiar with servicing the SRS
system and with proper handling of the air bag assembly.
Procedures should be read fully before they are
performed.
The following procedure requires use of J±42986 SRS
Deployment Harness with the appropriate pigtail adapter.
The procedure also requires the use of J±41497
Passenger Side SRS Module Deployment Fixture. Do
not attempt this procedure without J±42986 and fixture
J±41497.
WARNING: FAILURE TO FOLLOW PROCEDURES IN
THE ORDER LISTED MAY RESULT IN PERSONAL
INJURY. NEVER CONNECT DEPLOYMENT
HARNESS TO ANY POWER SOURCE BEFORE
CONNECTING DEPLOYMENT HARNESS TO THE AIR
BAG ASSEMBLY. DEPLOYMENT HARNESS SHALL
REMAIN SHORTED AND NOT BE CONNECTED TO A
POWER SOURCE UNTIL THE AIR BAG IS TO BE
DEPLOYED. THE AIR BAG ASSEMBLY WILL
IMMEDIATELY DEPLOY THE AIR BAG WHEN A
POWER SOURCE IS CONNECTED TO IT. WEAR
SAFETY GLASSES THROUGHOUT THIS ENTIRE
DEPLOYMENT AND DISPOSAL PROCEDURE.
NOTE: This information applies only to passenger air bag
assembly. Information for disposing of a live driver air bag
assembly can be found in ªDeployment Outside Vehicleº
(Driver Air Bag Assembly) in this section.
1. Turn ignition switch to ªLOCKº remove key, and put on
safety glasses.
2. Inspect J±41434 SRS Deployment Harness and
appropriate pigtail adapter for damage. If harness or
pigtail is damaged, discard and obtain a replacement.
3. Short the two SRS Deployment Harness leads
together by fully seating one banana plug into the
other. The SRS Deployment Harness shall remain
shorted and not be connected to a power source until
the air bag is to be deployed.
827RS003
4. Connect the appropriate pigtail adapter to the SRS
Deployment Harness
827RS004
5. Remove passenger air bag assembly from vehicle.
Refer to ªPassenger Air Bag Assembly Removal º in
this Section.
6. Clear a space on the ground approximately 185 cm
(six feet) in diameter where the fixture with attached
air bag assembly is to be placed for deployment. A
paved outdoor location where there is no activity is
preferred. If an outdoor location is not available, a
space on the shop floor where is no activity and
sufficient ventilation is recommended. Ensure that no
loose or flammable objects are within the deployment
area.
7. Place the J±41497 on the bench vice. This is
necessary to provide sufficient stabilization of the
fixture during deployment.
8. Attach the passenger air bag assembly in the
J±41497. Air bag assembly must be mounted such
that the bag will deploy upward. SECURELY
HAND±TIGHTEN ALL FASTENERS PRIOR TO
DEPLOYMENT.
9. Stretch the SRS Deployment Harness and pigtail
adapter from the air bag assembly to its full length.
10. Place a power source near the shorted end of the
SRS deployment harness. (Recommended
application: 12 volts minimum, 2 amps minimum. A
vehicle battery is suggested.)
11. Connect the air bag assembly to the pigtail adapter on
the SRS deployment harness. The SRS Deployment
Harness shall remain shorted and not be connected
to a power source until the air bag is to be deployed.
The air bag assembly will immediately deploy the air
bag when a power source is connected to it.
NOTE: Ensure that the pigtail adapter is firmly seated into
the air bag assembly connector. Failure to fully seat the
connectors may leave the shorting bar located in the air
bag assembly connector functioning (shorting the
deployment circuit) and may result in non deployment of
the air bag assembly.
12. Verify that the area around the passenger air bag
assembly is clear of all people and loose or flammable
objects.