2002 ISUZU AXIOM mirror

4D2±30
TRANSFER CASE (TOD)
Bearing
Check the profile of the needle, roller, ball, and thrust
bearings. Wash the bearings with clean detergent
completely, and dry with air.
NOTE: If the bearing is rotated excessively, the rollers
may be damaged. So, rotate the bearing slowly with your
hand. Apply grease to the bearing, and check the
smoothness of the bearing while slowly rotating the race
with your hand.
Allowable limit : 0.23 mm (0.009 in)
226RW143
Lockup Fork Spring
Check the lockup fork spring for distortion, cracking, and
wear. If defects are observed, replace the part.
Multi Plate Disk Clutch

If the burned, mirror-surfaced clutch facing, or
scraping is observed on the clutch plates, clutch
housing, armature plate, and insulator washer,
replace the parts.
266R200003
Legend
(1) Clutch Housing
(2) Clutch Plate
(3) Insulator Washer
(4) Armature Plate
Coil Assembly

Check the resistance of the coil with a tester. If
defects are observed, replace the coil assembly.
Standard : 1.7+0.3
(at ordinary temperature)
Allowable limit : 1.0~5.0

261RY00022
Cam Pulley, Cam Ball, and Cam & Coil
Housing

Check the cam balls and cam for excessive wear or
damage. If defective, replace the parts.
266RW016

5C±11 POWER±ASSISTED BRAKE SYSTEM
330RW012
17. Bleed the air from the front wheel brake pipe
connection (2) by repeating steps 7 through 16.
Bleeding the Caliper
18. Bleed the air from each wheel in the order listed
below:

Right rear caliper or wheel cylinder

Left rear caliper or wheel cylinder

Right front caliper

Left front caliper
Conduct air bleeding from the wheels in the above
order. If no brake fluid comes out, it suggests that air
is mixed in the master cylinder. In this case, bleed air
from the master cylinder in accordance with steps 7
through 17, and then bleed air from the caliper or
wheel cylinder.
19. Place the proper size box end wrench over the
bleeder screw.
20. Cover the bleeder screw with a transparent tube, and
submerge the free end of the transparent tube in a
transparent container containing brake fluid.
21. Pump the brake pedal slowly three (3) times
(once/sec), then hold it depressed.
22. Loosen the bleeder screw until fluid flows through the
tube.
23. Retighten the bleeder screw.
24. Release the brake pedal slowly.
25. Repeat steps 21 through 24 until the air is completely
removed.
It may be necessary to repeat the bleeding procedure
10 or more times for front wheels and 15 or more
times for rear wheels.
26. Go to the next wheel in the sequence after each wheel
is bled.
Be sure to monitor reservoir fluid level.
27. Depress the brake pedal to check if you feel
ªsponginessº after the air has been removed from all
wheel cylinders and calipers.
If the pedal feels ªspongyº, the entire bleeding
procedure must be repeated.28. After the bleeding operation is completed on the each
individual wheel, check the level of the brake fluid in
the reservoir and replenish up to the ªMAXº level as
necessary.
29. Attach the reservoir cap.
If the diaphragm inside the cap is deformed, reform
it and install.
30. Stop the engine.
Flushing Brake Hydraulic System
It is recommended that the entire hydraulic system be
thoroughly flushed with clean brake fluid whenever new
parts are installed in the hydraulic system. Approximately
one quart of fluid is required to flush the hydraulic system.
The system must be flushed if there is any doubt as to the
grade of fluid in the system or if fluid has been used which
contains the slightest trace of mineral oil. All rubber parts
that have been subjected to a contaminated fluid must be
replaced.
Brake Pipes and Hoses
The hydraulic brake system components are
interconnected by special steel piping and flexible hoses.
Flexible hoses are used between the frame and the front
calipers, the frame and rear axle case and the rear axle
and the rear calipers.
When the hydraulic pipes have been disconnected for
any reason, the brake system must be bled after
reconnecting the pipe. Refer to
Bleeding the Brake
Hydraulic System
in this section.
Brake Hose Inspection
The brake hose should be inspected at least twice a year.
The brake hose assembly should be checked for road
hazard, cracks and chafing of the outer cover, and for
leaks and blisters. Inspect for proper routing and
mounting of the hose. A brake hose that rubs on
suspension components will wear and eventually fail. A
light and mirror may be needed for an adequate
inspection. If any of the above conditions are observed on
the brake hose, adjust or replace the hose as necessary.
CAUTION: Never allow brake components such as
calipers to hang from the brake hoses, as damage to
the hoses may occur.

5C±71 POWER±ASSISTED BRAKE SYSTEM
NOTE: Do not allow the fluid level in the reservoir to go
below the half±way mark.
12. Reconnect the brake pipe (1) to the master cylinder
and tighten the pipe.
13. Depress the brake pedal slowly once and hold it
depressed.
14. Loosen the rear wheel brake pipe (1) at the master
cylinder.
15. Retighten the brake pipe, then release the brake
pedal slowly.
16. Repeat steps 13 through 15 until no air comes out of
the port when the brake pipe is loosened
NOTE: Be very careful not to allow the brake fluid to come
in contact with painted surfaces.
330R200004
17. Bleed the air from the front wheel brake pipe
connection (2) by repeating steps 7 through 16.
Bleeding the Caliper
18. Bleed the air from each wheel in the order listed
below:

Right rear caliper or wheel cylinder

Left rear caliper or wheel cylinder

Right front caliper

Left front caliper
Conduct air bleeding from the wheels in the above
order. If no brake fluid comes out, it suggests that air
is mixed in the master cylinder. In this case, bleed air
from the master cylinder in accordance with steps 7
through 17, and then bleed air from the caliper or
wheel cylinder.
19. Place the proper size box end wrench over the
bleeder screw.
20. Cover the bleeder screw with a transparent tube, and
submerge the free end of the transparent tube in a
transparent container containing brake fluid.
21. Pump the brake pedal slowly three (3) times
(once/sec), then hold it depressed.
22. Loosen the bleeder screw until fluid flows through the
tube.
23. Retighten the bleeder screw.24. Release the brake pedal slowly.
25. Repeat steps 21 through 24 until the air is completely
removed.
It may be necessary to repeat the bleeding procedure
10 or more times for front wheels and 15 or more
times for rear wheels.
26. Go to the next wheel in the sequence after each wheel
is bled.
Be sure to monitor reservoir fluid level.
27. Depress the brake pedal to check if you feel
ªsponginessº after the air has been removed from all
wheel cylinders and calipers.
If the pedal feels ªspongyº, the entire bleeding
procedure must be repeated.
28. After the bleeding operation is completed on the each
individual wheel, check the level of the brake fluid in
the reservoir and replenish up to the ªMAXº level as
necessary.
29. Attach the reservoir cap.
If the diaphragm inside the cap is deformed, reform
it and install.
30. Stop the engine.
Flushing Brake Hydraulic System
It is recommended that the entire hydraulic system be
thoroughly flushed with clean brake fluid whenever new
parts are installed in the hydraulic system. Approximately
one quart of fluid is required to flush the hydraulic system.
The system must be flushed if there is any doubt as to the
grade of fluid in the system or if fluid has been used which
contains the slightest trace of mineral oil. All rubber parts
that have been subjected to a contaminated fluid must be
replaced.
Brake Pipes and Hoses
The hydraulic brake system components are
interconnected by special steel piping and flexible hoses.
Flexible hoses are used between the frame and the front
calipers, the frame and rear axle case and the rear axle
and the rear calipers.
When the hydraulic pipes have been disconnected for
any reason, the brake system must be bled after
reconnecting the pipe. Refer to
Bleeding the Brake
Hydraulic System
in this section.
Brake Hose Inspection
The brake hose should be inspected at least twice a year.
The brake hose assembly should be checked for road
hazard, cracks and chafing of the outer cover, and for
leaks and blisters. Inspect for proper routing and
mounting of the hose. A brake hose that rubs on
suspension components will wear and eventually fail. A
light and mirror may be needed for an adequate
inspection. If any of the above conditions are observed on
the brake hose, adjust or replace the hose as necessary.
CAUTION: Never allow brake components such as
calipers to hang from the brake hoses, as damage to
the hoses may occur.

LIGHTING SYSTEM8A±1
AXIOM
BODY AND ACCESSORIES
CONTENTS
Lighting System 8A. . . . . . . . . . . . . . . . . . . . . . . . .
Wiper / Washer System 8B. . . . . . . . . . . . . . . . . .
Entertainment 8C. . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring System 8D. . . . . . . . . . . . . . . . . . . . . . . . . .
Meter and Gauge 8E. . . . . . . . . . . . . . . . . . . . . . . Body Structure 8F. . . . . . . . . . . . . . . . . . . . . . . . . .
Seats 8G. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security and Locks 8H. . . . . . . . . . . . . . . . . . . . . .
Sunroof / Convertible Top 8I. . . . . . . . . . . . . . . .
Exterior / Interior Trim 8J. . . . . . . . . . . . . . . . . . . .
LIGHTING SYSTEM
CONTENTS
Service Precaution 8A±2. . . . . . . . . . . . . . . . . . . . . .
Headlight Bulb 8A±3. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight Assembly 8A±4. . . . . . . . . . . . . . . . . . . . .
Removal 8A±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight Adjustment 8A±4. . . . . . . . . . . . . . . . . .
Side Marker Light Bulb 8A±6. . . . . . . . . . . . . . . . . . .
Removal 8A±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Taillight Bulb 8A±7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±7. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Plate Light Bulb 8A±8. . . . . . . . . . . . . . . . . .
Removal 8A±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stoplight Bulb 8A±8. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation 8A±8. . . . . . . . . . . . . . .
High Mounted Stoplight Assembly 8A±9. . . . . . . . .
Removal 8A±9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Mounted Stoplight Bulb 8A±9. . . . . . . . . . . . . .
Removal 8A±9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backup Light Bulb 8A±10. . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±10. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Turn Signal Light Bulb 8A±10. . . . . . . . . . . . . .
Removal and Installation 8A±10. . . . . . . . . . . . . . .
Rear Turn Signal Light Bulb 8A±11. . . . . . . . . . . . . .
Removal 8A±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dome Light Bulb 8A±11. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . Map Light Bulb 8A±12. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Courtesy Light Bulb 8A±12. . . . . . . . . . . . . . . . . . . . . .
Removal 8A±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Room Light Bulb 8A±13. . . . . . . . . . . . . . . .
Removal 8A±13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Lever Illumination Light Bulb (A/T) 8A±13. . . .
Removal 8A±13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vanity Mirror Illumination Light Bulb 8A±14. . . . . . . .
Removal 8A±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch Unit Assembly Illumination
Light Bulb (Power/Winter & Intelligent
Suspension Switch) 8A±14. . . . . . . . . . . . . . . . . . . . .
Removal 8A±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOD Switch Illumination Light Bulb 8A±15. . . . . . . .
Removal 8A±15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise Control Main Switch Illumination
Light Bulb 8A±15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wiper and Washer Switch Illumination
Light Bulb 8A±16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A±16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat Heater Switch Illumination Light Bulb 8A±16. .
Removal 8A±16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A±16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Switch 8A±17. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation 8A±17. . . . . . . . . . . . . . .
Lighting Switch (Combination Switch) 8A±17. . . . . .

8A±14LIGHTING SYSTEM
Vanity Mirror Illumination Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (1).
3. Remove the bulb (2).
805R200004
Installation
To install, follow the removal steps in the reverse order.
Switch Unit Assembly Illumination Light Bulb
(Power/Winter & Intelligent Suspension Switch)
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster assembly.

Refer to
Instrument Panel Assembly in Body
Structure
section.
3. Remove the audio.

Refer to
Audio in Entertainment section.
4. Remove the illumination light bulb.
825R200036
Installation
To install, follow the removal steps in the reverse order.

LIGHTING SYSTEM8A±21
Main Data and Specifications
Light and Bulb Specifications
801R200020
Legend
(1) High Mounted Stoplight
(2) Luggage Room Light
(3) Vanity Mirror Illumination Light
(4) Map Light
(5) Dome Light
(6) Meter(7) Front Turn Signal Light/Front Side Marker
Light/Parking Light
(8) Headlight
(9) Courtesy Light
(10) Taillight/Stoplight
(11) Backup Light
(12) Rear Turn Signal Light
(13) License Plate Light

8A±22LIGHTING SYSTEM
Light NameBulb No.Rated
PowerNumber of
BulbsLens ColorRemarks
Headlight9005/900660w/51w2WhiteHalogen
Front Turn signal Light/
Front Side Marker Light/Parking Light1157NA27w/8w2Amber
Rear Turn Signal Light744021w2Amber
Backup Light92118w2White
Taillight/Stoplight744321w/5w2Red
High Mounted Stoplight92118w2Red
License Plate Light (Tailgate type)1685w2White
Map LightÐ8w2White
Dome LightÐ10w1White
Luggage Room LightÐ5w1White
Courtesy LightÐ3.4w4White
Check TransÐ1.4w1RedMeter
A/T Oil TempÐ1.4w1RedMeter
Cruise SetÐ1.4w1GreenMeter
Power DriveÐ1.4w1AmberMeter
Winter DriveÐ1.4w1GreenMeter
Turn SignalÐ1.4w2GreenMeter
Check TODÐ1.4w1RedMeter
High BeamÐ1.4w1BlueMeter
ABSÐ1.4w1AmberMeter
Seat BeltÐ2w1RedMeter
Indicator/Warning
Malfunction Indicator
(Check Engine)Ð1.4w1AmberMeter
Indicator/Warning
LightLow FuelÐ1.4w1AmberMeterg
Reduced PowerÐ1.4w1AmberMeter
Sports ModeÐ1.4w1GreenMeter
TOD FrontÐ1.1w1GreenMeter
TOD AutoÐ1.1w1GreenMeter
TOD RearÐ1.1w1GreenMeter
Oil PressureÐ1.4w1RedMeter
Brake SystemÐ1.4w1RedMeter
ChargeÐ1.4w1RedMeter
A/T Shift PositionÐ1.1w7
P,N,D,3,2,L
:Green
R: Amber
Meter
Air BagÐ2w1RedMeter
Illumination LightMeterÐ3.4w4Meter
Shift leverÐ1.4w1WhiteShift lever
Vanity MirrorÐ2w2WhiteSun Visor
Cigarette LighterÐ1.4w1WhiteCigarette
Lighter
AshtrayÐ1.4w1WhiteAshtray

8D±1
WIRING SYSTEM
AXIOM
BODY AND ACCESSORIES
WIRING SYSTEM
CONTENTS
Fuse, Relay and Diode 8D±2. . . . . . . . . . . . . . . . . . .
Relay / Fuse Box Location 8D±2. . . . . . . . . . . . . .
Relay / Fuse Box (Instrument Panel) 8D±3. . . . .
Relay / Fuse Box (Engine Room) 8D±4. . . . . . . .
Circuit Diagram 8D±5. . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Block Circuit 8D±5. . . . . . . . . . . . . . . . . . . . .
Ground Location (Engine Room) 8D±6. . . . . . . .
Ground Location (Cabin) 8D±7. . . . . . . . . . . . . . .
Starter and Generator 8D±8. . . . . . . . . . . . . . . . . .
PCM±1 8D±9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCM±2 8D±10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight and Fog Light 8D±11. . . . . . . . . . . . . . . .
Turn, Hazard, Stop, Back Up, Horn and
A/T Shift Lock 8D±12. . . . . . . . . . . . . . . . . . . . . . . .
Dome Light, Luggage Room Light, Courtesy
Light, Spot Light, and Warning Buzzer 8D±13. . .
Power Window and Door Lock 8D±14. . . . . . . . . .
Alarm and Relay Control Unit 8D±15. . . . . . . . . . . Rear Wiper/Washer and Rear Defogger 8D±16. .
Audio, Clock, Cigarette Lighter and
ACC Socket 8D±17. . . . . . . . . . . . . . . . . . . . . . . . . .
MID 8D±18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Mirror 8D±19. . . . . . . . . . . . . . . . . . . . . . . . . . .
Meter 8D±20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anti-theft with Keyless Entry 8D±21. . . . . . . . . . . .
Air Conditioning 8D±22. . . . . . . . . . . . . . . . . . . . . . .
ABS 8D±23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SRS±Air Bag 8D±24. . . . . . . . . . . . . . . . . . . . . . . . . .
Intelligent Suspension 8D±25. . . . . . . . . . . . . . . . . .
T.O.D 8D±26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sunroof 8D±27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Illumination Light 8D±28. . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D±29. . . . . . . . . .
Power Seat 8D±30. . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat Heater 8D±31. . . . . . . . . . . . . . . . . . . . . . . . . . .