2001 TOYOTA SEQUOIA parking brake

BR10A±04
F13306
No. 2 Heater to Register DuctLower Finish Panel
Hood Lock
Release Lever Parking Brake Wire
Clip
Pedal Pad Parking Brake
Pedal Assembly
: Specified torque
N´m (kgf´cm, ft´lbf)
Cowl Side Trim BoardFront Door Scuff Plate
13 (130, 9)
Adjusting Nut
Lock Nut Clip
Return Spring
Return Spring Damper
32 (320, 23)
Parking Brake Switch Cushion
5.4 (55, 48 in.´lbf)
Pedal Assembly
Lithium soap base glycol grease

Non±reusable part
Bushing
Bushing
Pedal Bracket
Parking Brake Switch
Connector
Side Panel BR±10
± BRAKEPARKING BRAKE PEDAL
3177 Author: Date:
2005 SEQUOIA (RM1146U)
COMPONENTS

BR10B±04
± BRAKEPARKING BRAKE PEDAL
BR±11
3178 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT DOOR SCUFF PLATE, COWL SIDE TRIM BOARD, SIDE PANEL, LOWER FIN-
ISH PANEL AND NO. 2 HEATER TO REGISTER DUCT (See page BO±89)
2. REMOVE PARKING BRAKE PEDAL ASSEMBLY
(a) Disconnect the parking brake switch connector.
(b) Remove the lock nut and adjusting nut from the parking brake wire.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(c) Remove the clip and disconnect the parking brake wire from the parking brake pedal assembly.
(d) Remove the 4 bolts and parking brake pedal assembly.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)

BR1NB±02
BR±12
± BRAKEPARKING BRAKE PEDAL
3179 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
1. REMOVE RETURN SPRING AND RETURN SPRING DAMPER
2. REMOVE CUSHION
3. REMOVE PEDAL ASSEMBLY
(a) Remove the nut, bolt and pedal assembly.
Torque: 32 N´m (320 kgf´cm, 23 ft´lbf)
(b) Remove the 2 bushings from the pedal assembly.
(c) Remove the pedal pad.
4. REMOVE PARKING BRAKE SWITCH
Remove the screw and parking brake switch.

BR1NC±02
± BRAKEPARKING BRAKE PEDAL
BR±13
3180 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BR±12).
NOTICE:
Apply lithium soap base glycol grease to the parts indicated by the arrows (See page BR±10).

BR10C±03
BR±14
± BRAKEPARKING BRAKE PEDAL
3181 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page BR±11).
HINT:
After the installation, check and adjust parking brake pedal travel (See page BR±9).

BR0JX±17
F13341
PinRear Disc Brake
Assembly
Front Shoe
C±washer
ShimParking Brake Shoe
Lever
Rear Shoe
Shoe Strut
Spring
Adjuster
CupTension Spring Shoe Hold±down
Spring
Disc
High temperature grease
N´m (kgf´cm, ft´lbf) : Specified torqueAnchor SpringCup
Shoe Hold±down
Spring
Shoe Return
Spring
105 (1,070, 77)

Non±reusable part BR±42
± BRAKEPARKING BRAKE
3209 Author: Date:
2005 SEQUOIA (RM1146U)
PARKING BRAKE
COMPONENTS

BR1NF±02
F13327
F13323
F13324
± BRAKEPARKING BRAKE
BR±43
3210 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
1. REMOVE REAR WHEEL
Torque: 110 N´m (1,122 kgf´cm, 81 ft´lbf)
2. REMOVE REAR DISC BRAKE ASSEMBLY
(a) Remove the 2 mounting bolts and remove the disc brake
assembly.
Torque: 105 N´m (1,070 kgf´cm, 77 ft´lbf)
(b) Suspend the disc brake securely and so the hose is not
stretched.
3. REMOVE DISC
(a) Release the parking brake lever.
(b) Place matchmarks on the disc and rear axle hub.
(c) Remove the disc.
HINT:

If the disc cannot be removed easily, turn the shoe adjust-
er until the wheel turns freely.

If there are no matchmarks, temporarily install the disc,
then measure the disc runout and install the disc in posi-
tion (See page BR±39).
4. REMOVE SHOE RETURN SPRINGS
Using needle±nose pliers, remove the 2 shoe return springs.
5. REMOVE SHOE STRUT WITH SPRING
HINT:
At the time of reassembly, install the strut with the spring facing
forward.
6. REMOVE SHOE ADJUSTER
Slide the front shoe toward outside, remove the shoe adjuster.
7. REMOVE FRONT SHOE
(a) Using a needle±nose pliers, disconnect the anchor spring
and tension spring from the front shoe.
(b) Remove the anchor spring and tension spring.

F13325
F13901
F13326
BR±44
± BRAKEPARKING BRAKE
3211 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Using a clip remover, remove the front shoe with holding
the cup.
HINT:
At the time of reassembly, hold the cup with clip remover. In this
condition, install the front shoe.
(d) Remove the 2 cups, shoe hold±down spring and pin.
8. REMOVE REAR SHOE
(a) Using a clip remover, remove the rear shoe with holding
the cup.
HINT:
At the time of reassembly, hold the cup with clip remover. In this
condition, install the rear shoe.
(b) Remove the 2 cups, shoe hold±down spring and pin.
(c) Disconnect the parking brake cable from the parking
brake shoe lever.