2001 TOYOTA SEQUOIA airbag

H16720
4 Claws
H16721
Clip
H11151
H17633
w/o Rear No. 2 seat:
w/ Rear No. 2 seat:
± BODYROOF HEADLINING
BO±103
3656 Author: Date:
2005 SEQUOIA (RM1146U)
11. w/o Curtain shield airbag asseindly:
REMOVE ASSIST GRIP
(a) Using a screwdriver, remove the No. 2 assist grip piug.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws and assist grip.
(c) Use the same manner described above to the other side.
12. REMOVE CENTER PILLAR GARNISH
(a) Remove the clip.
(b) Remove the center pillar garnish.
(c) Use the same manner described above to the other side.
13. REMOVE DOME LIGHT
(a) Using a screwdriver, remove the lens.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws and dome light, then disconnect the
connector.
14. REMOVE REAR TRIM COVER
Using a screwdriver, remove the rear trim cover.
HINT:
Tape the screwdriver tip before use.

H16736
± BODYROOF HEADLINING
BO±107
3660 Author: Date:
2005 SEQUOIA (RM1146U)
32. REMOVE SUN VISORS AND HOLDERS
33. REMOVE ROOF HEADLINING
(a) Using a clip remover, remove the 2 clips.
(b) Remove the roof headlining.
34. w/ Rear A/C:
REMOVE REAR AIR DUCTS
35. w/ Rear A/C:
REMOVE FRONT SIDE RAIL SPACERS
36. w/o Rear A/C:
REMOVE REAR NO. 2 SIDE RAIL SPACERS
37. w/o Curtain shield airbag assembly:
REMOVE FRONT PILLAR SPACERS
38. REMOVE FRONT ROOF HEADLINING TRIM RETAIN-
ERS
39. REMOVE REAR ROOF HEADLINING TRIM RETAIN-
ERS
40. REMOVE NO. 1 ROOF HEADLINING TRIM SIDE RE-
TAINERS

BO4S6±01
H24329
37 (380, 27)
37 (380, 27)
37 (380, 27)
37 (380, 27)
37 (380, 27)
42 (430, 32) Seatback Cover
Seat Cushion
Cover
Seat Cushion
PadArmrest CapArmrest Spacer
Armrest
Lock Plate
Spacer
Armrest
AssemblyHeadrest
Headrest Support Seatback Pad
Lumbar Support
Adjuster
Seat Frame Assembly Seat Position Sensor
Protector
Seat Position
Sensor
Seat Cushion
Inner Shield
Seat Cushion
Lower ShieldFront Seat Inner BeltRH Reclining
Adjuster Inside
CoverRH Seatback
ShieldVertical Adjuster
Bracket Inner Cover
Vertical Adjuster
Bracket Outer Cover
LH Reclining
Adjuster Inside Cover
Reclining Knob
Slide Knob
Seat Cushion Outer ShieldLumbar Switch Power Seat SwitchLH Seatback Shield

Hog RingSeat Track
Cover
Seat Track
CoverBushing

Hog Ring
Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)


w/ Side airbag:
5.5 (56, 49 in.´lbf)
w/ Seat heater:
w/ Seat heater:
Seat Cushion Heater Assembly
Seatback
Heater Assembly
Occupant Classification ECUPassenger's seat:
Driver's seat:
Driver's seat:
BO±110
± BODYFRONT SEAT (Power Adjuster Type)
3663 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT SEAT (Power Adjuster Type)
COMPONENTS
HINT:
The procedures listed below are for the LH side.

BO4S7±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±111
3664 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the body.

H24861
H24321
Hog Ring
H24318Hog Ring
H24319
H24320
BO±114
± BODYFRONT SEAT (Power Adjuster Type)
3667 Author: Date:
2005 SEQUOIA (RM1146U)
(c) w/ Side airbag:
Remove the nut and disconnect the seatback cover
bracket from the seat frame assembly.
(d) Remove the hog rings from the seat frame assembly.
(e) Remove the hog rings from the seat frame assembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. w/ Seat heater:
REMOVE SEATBACK HEATER ASSEMBLY
Cut off the tack pins which fasten the seat heater, and then re-
move the seatback heater assembly from the seatback cover.
11. REMOVE SEAT CUSHION COVER AND PAD
(a) Disconnect the wire harness clamp.
(b) Remove the 2 clips.

H24319
H24318Hog Ring
H24321Hog Ring
H24861
H24317
BO±120
± BODYFRONT SEAT (Power Adjuster Type)
3673 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Turn up the seatback cover and install the hog rings.
11. INSTALL SEATBACK COVER AND PAD
(a) Install the seatback cover and pad to the seat frame as-
sembly.
(b) Install the hog rings to the seat frame assembly.
(c) Install the hog rings to the seat frame assembly.
(d) w/ Side airbag:
Connect the seatback cover bracket to the seat frame as-
sembly with the nut.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
(e) Close the fastener.
(f) Install the hog rings to the seat frame assembly.

BO4S9±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±123
3676 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.

BO4SB±01
H24345
RH Lower Reclining
Adjuster Inside Cover
Seat Cushion
Outer Shield
Vertical Adjuster Handle Cap Reclining Adjuster Release Handle Seat Cushion
Inner ShieldRH Upper Reclining
Adjuster Inside Cover
RH Seat Cushion
Lower Shield
LH Lower Reclining
Adjuster Inside CoverLH Upper Reclining
Adjuster Inside CoverLH Seat Cushion
Lower Shield
Vertical Adjuster Handle
Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)

Driver's seat:
Driver's seat:
37 (380, 27)
37 (380, 27)37 (380, 27)
37 (380, 27)
42 (430, 32) Seatback Cover
Seat Cushion
Cover
Seat Cushion
PadArmrest CapArmrest SpacerArmrest
Lock Plate
Spacer
Armrest AssemblyHeadrest
Headrest Support Seatback Pad
Seat Frame Assembly
Seat Position Sensor
Protector
Seat Position Sensor
Front Seat
Inner Belt
Hog RingSeat Track Cover
Seat Track Cover

Hog Ring
37 (380, 27)
Occupant Classification ECUPassenger's seat:
w/ Side airbag:
5.5 (56, 49 in.´lbf)
BO±124
± BODYFRONT SEAT (Manual Adjuster Type)
3677 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT SEAT (Manual Adjuster Type)
COMPONENTS
HINT:
The procedures listed below are for the LH side.