2001 TOYOTA SEQUOIA check oil

D14138
D14141
DI±534
± DIAGNOSTICSAUTOMATIC TRANSMISSION
728 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Add ATF through the refill hole until it drains out from
the overflow hole.
(3) Install the overflow plug with a new gasket when the
draining ATF has become a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(4) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(5) Lower down the vehicle.
(6) Turn the ignition switch off.
(7) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.

D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
C13480D14149
GND
2 V/DIV
20 ms/DIV
DI±596
± DIAGNOSTICSAUTOMATIC TRANSMISSION
790 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0722 Output Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the
ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the
speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assy rotates, and this voltage
is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock±up timing are controlled by the ECM based on the signals from this vehicle
speed sensor and the throttle position sensor signal.
DTC No.DTC Detection ConditionTrouble Area
P0722
All conditions below are detected 500 times or more continu-
ously (1±trip detection logic)
(a) No signal from speed sensor (SP2) is input to ECM while 4
pulses of No. 1 vehicle speed sensor signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
(c) Park/neutral position switch is OFF.
(d) Transfer position is except neutral (4WD).

Open or short in speed sensor (SP2) circuit

Speed sensor (SP2)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals SP2+ and SP2±
of the ECM connector.
Standard: Refer to the illustration.
TerminalSP2+ ± SP2±
Tool setting2V/DIV, 20ms/DIV
Vehicle conditionVehicle speed 20 km/h (12 mph)
DIDJ9±01

D14169
1±2 Shift Valve
Valve Body:
DI±636
± DIAGNOSTICSAUTOMATIC TRANSMISSION
830 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0781 1±2 Shift (1±2 Shift Valve)
SYSTEM DESCRIPTION
The 1±2 shift valve performs shifting to 1st gear and other
gears.
DTC No.DTC Detection ConditionTrouble Area
P0781The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Valve body is blocked up or stuck (1±2 shift valve)

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates that the 1±2 shift valve in the valve body is locked in the direction the spring compresses.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº and switching oil pressure
to the valves in the valve body.
The ECM calculates the ºactualº transmission gear by comparing the signals from the input speed sensor
(NCO) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift sole-
noids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear
position and the commanded gear position are different, it will illuminate the MIL and store the DTC .
MONITOR STRATEGY
Related DTCsP0781Valve body/Rationality check
MainValve body
Required sensors/ComponentsSubAutomatic transmission assembly, Speed sensor (NT), Speed sensor
(NO), Vehicle speed sensor, Throttle speed sensor
Frequency of operationContinuous
Conditions (A) and (B)0.4 sec.
DurationCondition (C)3 sec.Duration
Condition (D)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJH±01

DI1AP±40
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1573
1767 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
SymptomSuspected AreaSee page
Immobiliser is not set.
(Engine starts with key codes other than the registered key code.)1. Door courtesy light switch circuit (DTC12)
2. Transponder key ECUDI±1585
IN±35
Engine does not start.
1. Key
2. Key unlock warning switch circuit (DTC11)
3. Transponder key coil
4. Transponder key ECU
5. ECM*1
DI±1582
BE±143
IN±35
IN±35
Security indicator is always ON.
1. Security indicator
2. Security indicator light circuit
3. Transponder key ECU*2
DI±1597
IN±35
Security indicator is always ON.
(Although code has been registered in the automatic registration
mode, indicator is not OFF.)1. Transponder key coil
2. Transponder key ECUBE±143
IN±35
Security indicator is OFF.
(When DTC of immobiliser is output)1. Transponder key coil
2. Transponder key ECUBE±143
IN±35
Security indicator is OFF.
(When DTC of immobiliser is not output)1. Security indicator light circuit
2. Diagnosis circuit
3. Transponder key ECUDI±1597
DI±1599
IN±35
Security indicator is abnormally blinking.Transponder key ECUIN±35
No code is output.
1. Power source circuit
2. Diagnosis circuit
3. Transponder key ECUDI±1595
DI±1599
IN±35
*1 : Check that the key which did not start the engine has been registered, and that it is possible to start with
any other already registered key.
*2 : Finish the automatic registration mode because the mode might still be set.

DI±1590
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1784 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check whether the engine can be started with the master key and sub±key for
another vehicle of the same type.
RESULT:
AAll keys start the engine.
BA specific key does not start the engine. In this case, DTC
21 or 22 is not stored in memory.
CAll keys do not start the engine. In this case, DTC 21 and 22
are not stored in memory.
A No problem at this time.
HINT:
If the result is ºAº, confirm whether or not the customer has ever
inserted the key (without a transponder chip) of another vehicle
into the ignition key cylinder.
B The transponder chip of a specific key is defec-
tive. Replace the key.
C
2 Check transponder key coil (See page BE±143).
NG Replace transponder key coil.
OK
3 Check harness and connector between transponder key ECU and transponder
key amplifier (See page IN±35).
NG Repair or replace harness or connector.
OK

DID8Q±01
DI±1608
± DIAGNOSTICSCOMBINATION METER SYSTEM
1802 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. METER GAUGE AND WARNING/INDICATOR
GAUGE:
ItemDetail
SpeedometerVehicle speed sensor (Direct line).
TachometerECM transmits engine speed to the meter to display.
ODO/TRIP MeterCombination meter assy.
FuelDisplays a fuel level according to a signal from the fuel sender gauge (Direct line).
Water TemperatureDisplays engine coolant temperature according to a signal from the ECM (BEAN).
Oil PressureReceives a signal from the oil pressure sender (Direct line).
Volt MeterDisplays vehicle voltage according to a voltage from the IG terminal (Direct line).
WARNING/INDICATOR:
HINT:
Combination meter bulb check is performed for 3 seconds after the ignition switch is turned ON.
ItemDetailList of indicators available for
bulb check
O/D OFFReceives a signal from the ECM (Direct line)±
TURNTurns signal switch ON (Direct line)±
BEAMReceives a signal from the body ECU (*1), Displays a signal received from the
dimmer switch (*2) (Direct line)±
SECURITYReceives a set signal from the transponder key ECU and body ECU (Direct line)±
CHARGEReceives a malfunction signal from the alternator (Direct line)
AIR BAGReceives a malfunction signal from the airbag sensor center (Direct line)
D SEAT BELTReceives the driver seat belt signal (Unfastened) from the seat belt inner front LH
(Direct line)±
DOOROpen door indicator comes on when a signal is received from the ECU (BEAN)
from each door±
A/T OIL TEMP.Warning is displayed when the oil temperature is high (Direct line)
BRAKEComes on when the parking brake switch is on or the brake fluid level warning
switch is on (Direct line)
MIL (CHECK ENGINE)Receives a malfunction signal from the ECM (Direct line)
FUEL WARNINGReceives the fuel empty signal from the fuel sender gauge (Direct line)±
ABSReceives a malfunction signal from the skid control ECU (Direct line)
WASHERWarning is displayed when the washer level is low (Direct line)±
CRUISEReceives a CRUISE on signal or malfunction signal from the ECM (Direct line)±
VSC TRACReceives a malfunction signal from the skid control ECU (Direct line)
VSC (TRAC) OFFReceives a malfunction signal from the translate ECU (Direct line)
SLIPReceives a malfunction signal from the translate ECU (Direct line)
4HIReceives a 4HI signal from the 4WD control ECU (Direct line)±
CTR DIF LOCKReceives a DIF LOCK signal from the 4WD control ECU (Direct line)±
A/T PReceives a P signal from the park/neutral position switch (Direct line)±
A/T NReceives an N signal from the park/neutral position switch (Direct line)±
A/T DReceives a D signal from the park/neutral position switch (Direct line)±
A/T 3Receives a 3 signal from the park/neutral position switch (Direct line)±
A/T 2Receives a 2 signal from the park/neutral position switch (Direct line)±
A/T LReceives an L signal from the park/neutral position switch (Direct line)±

DID8S±01
/ /
/ /
COMBINATION METER SYSTEM Check Sheet
Inspector 's name:
Customer 's NameVIN
Production Date
Licence Plate No.
Date Vehicle
Brought InOdometer Readingkm
miles
Weather Conditions
When Problem
OccurredFrequency Problem Occurs
Weather
Outside temperature Constantly  Sometimes ( times per day, month)
 Once only Date Problem First Occurred
 Fine  Cloudy  Rainy  Snowy
 Various/Others
 Hot  Warm  Cool
 Cold (Approx. 5F ( 5C))
Problem Symptom
Gauge

Malfunction in speedometer

Malfunction in tachometer

Malfunction in engine coolant temperature receiver gauge

Malfunction in fuel receiver gauge

Entire combination meter does not operate

Buzzer does not sound (Key reminder warning, Seat belt warning)

Seat belt warning for driver's seat does not operate
Others

Operating light control rheostat does not change light brightness

















Malfunction in oil pressure receiver gauge

Malfunction in volt meter DI±1612
± DIAGNOSTICSCOMBINATION METER SYSTEM
1806 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK

DID8U±01
DI±1614
± DIAGNOSTICSCOMBINATION METER SYSTEM
1808 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
Inspect the related ºFuseº and ºRelayº before confirming the suspected area as shown in the table below.
MALFUNCTION SYSTEM:
SymptomSuspected AreaSee page
Entire combination meter does not operate.Refer to troubleshooting proceduresDI±1628
Operating light control rheostat does not change light brightness.Refer to troubleshooting proceduresDI±1645
Seat belt warning does not operate.Refer to troubleshooting proceduresDI±1650
Key reminder warning buzzer does not sound.
1. Multiplex communication system
2. Key unlock warning switch circuit
3. Door courtesy lamp switch circuit
4. Combination meter assyDI±1892
DI±1715
DI±1728
IN±35
METER GAUGES:
SymptomSuspected AreaSee page
Malfunction in speedometerRefer to troubleshooting proceduresDI±1632
Malfunction in tachometerRefer to troubleshooting proceduresDI±1636
Malfunction in fuel receiver gaugeRefer to troubleshooting proceduresDI±1640
Malfunction in engine coolant temperature receiver gaugeRefer to troubleshooting proceduresDI±1644
Malfunction in oil pressure receiver gaugeRefer to troubleshooting proceduresDI±1654
Malfunction in volt meterRefer to troubleshooting proceduresDI±1658
WARNING LIGHTS:
SymptomSuspected AreaSee page
Check engine warning light (MIL) does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Discharge warning light does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Brake warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
ABS warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
SRS warning light does not come on.
1. Airbag sensor assy
2. Wire harness or connector
3. Combination meter assyDI±1126
±
IN±35
Open door warning light does not come on.
1. Door courtesy light switch circuit
2. Wire harness or connector
3. Combination meter assy
4. Body ECUDI±1728
±
IN±35
IN±35
Fuel level warning light does not come on.
1. Refer to troubleshooting
2. Wire harness or connector
3. Combination meter assyDI±1640
±
IN±35
Low oil pressure warning light does not come on.
1. Low oil pressure warning switch
2. Wire harness or connector
3. Combination meter assyBE±55
±
IN±35