2001 TOYOTA SEQUOIA Power switch

BE264±03
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE±73
3477 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
HOW TO RESET POWER WINDOW MOTOR (LIMIT SWITCH)
NOTICE:
If the jam protection function is not functioning properly, perform the following procedures.
HINT:
It is necessary to reset the power window motor (in initial position for the limit switch) when separating the
window regulator from the power window motor or operating the window regulator with the door glass not
installed.
(a) Remove the power window motor.
HINT:
Place matchmarks on the power window motor and window regulator gear.
(b) Connect the power window motor and power window switch to the wire harness of the vehicle.
(c) Turn the ignition switch ON.
(d) Press the power window UP switch until the motor completes 6 to 10 rotations (4 seconds of rotation
or more).
(e) Assemble the power window motor and regulator.
HINT:

Install the motor when the regulator arm is below the middle point.

Align the matchmarks on the power window motor and window regulator gear when installing the pow-
er window motor.
(f) Assemble the power window regulator and door glass.
HINT:
Never rotate the motor downward until the completion of the window glass installation.
(g) Connect the power window switch to the wire harness and turn the ignition switch ON.
(h) Repeat UP and DOWN operation several times manually.
(i) Check that AUTO UP " AUTO DOWN automatic operation is normal.
NOTICE:

The jam protection function does not operate immediately after performing reset.

If the jam protection function is triggered and the window lowers after the window has been fully
closed by AUTO UP operation (step i), reset the power window motor again.
(j) Check the power window function.

BE073±07
I28413
Back Door Power
Window Switch
Instrument Panel J/B
Back Door Key Lock
and Unlock Switch

Back Door Control Switch
Back Door Power Window Regulator
Assembly

Back Door Power Window Motor Body ECU
(Located behind the
Instrument Panel)
Back Door ECU
(Located inside of the back door trim board)
BE±74
± BODY ELECTRICALBACK DOOR POWER WINDOW CONTROL SYSTEM
3478 Author: Date:
2005 SEQUOIA (RM1146U)
BACK DOOR POWER WINDOW CONTROL SYSTEM
LOCATION

BE2MM±01
I18616
I18690
2
3 1DOWN UP
I27714
I27715
± BODY ELECTRICALBACK DOOR POWER WINDOW CONTROL SYSTEM
BE±75
3479 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT BACK DOOR POWER WINDOW SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
UP3 ± 6Continuity
OFF±No continuity
DOWN3 ± 5Continuity
If continuity is not as specified, replace the switch.
2. INSPECT BACK DOOR KEY LOCK AND UNLOCK
SWITCH CONTINUITY (Back Door Control Switch)
Switch positionTester connectionSpecified condition
UP1 ± 3Continuity
OFF±No continuity
DOWN2 ± 3Continuity
If continuity is not as specified, replace the switch.
3. INSPECT BACK DOOR POWER WINDOW MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 4 and check that
the motor turns clockwise.
(b) Connect the positive (+) lead from the battery to terminal
4 and the negative (±) lead to terminal 1 and check that
the motor turns counterclockwise.
If operation is not as specified, replace the back door power
window motor.

I28582
Back Door ECU:
A
1716
I28583
GND BE±76
± BODY ELECTRICALBACK DOOR POWER WINDOW CONTROL SYSTEM
3480 Author: Date:
2005 SEQUOIA (RM1146U)
4. INSPECT BACK DOOR POWER WINDOW PULSE
SENSOR (Using oscilloscope)
(a) Remove the back door ECU with the connectors still con-
nected.
(b) Connect the oscilloscope to terminals A±16 and A±17
and body ground.
(c) Operate the back door power window switch.
(d) Check the signal waveform according to the condition (s)
in the table below.
ItemCondition
Tool setting5V/DIV, 10 ms/DIV
Vehicle conditionIgnition switch ON
OK:
As shown in the illustration
5. INSPECT JAM PROTECTION FUNCTION
NOTICE:
Be careful not to get any part of your body caught when
checking.
HINT:
When performing resetting of the limit switch, do checking after
repeating up and down of the glass with automatic operation.
(a) Confirmation of AUTO up operation:
Confirm that the window will close fully with AUTO up op-
eration.
(b) Checking operation of the jam protection function:
(1) Raise the window with AUTO up operation and
check that the window goes down when it touches
the inserted handle of the hammer.
(2) Confirm that the window will then stop going down
after about 200 mm (7.87 in).
HINT:
When removing the glass, glass guide, regulator, etc. be sure
to perform a check of the jam protection function.
If the jam protection is not functioning properly, adjust the power
window motor switch and pulse switch.

BE2MN±01
± BODY ELECTRICALBACK DOOR POWER WINDOW CONTROL SYSTEM
BE±77
3481 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. RESET (INITIALIZE) POWER WINDOW REGULATOR MOTOR
NOTICE:
Resetting the power window regulator motor (initializing the pulse sensor) is necessary if: 1) the bat-
tery terminal cable is disconnected; 2) the back door ECU, wire harness, power window regulator
switch, power window regulator assembly and power window regulator motor are replaced or re-
moved/installed; or 3) the P/W fuse is replaced or removed. If resetting is not performed, the master
switch assembly will not be able to operate the AUTO operation function, jam protection function and
remote operation function.
(a) Turn the ignition switch ON.
(b) Open the power window halfway by pressing the power window switch.
(c) Fully pull up on the switch until the power window is fully closed and continue to hold the switch for
at least 1 second.
(d) Check that the AUTO UP/DOWN function operates normally.
If the AUTO UP/DOWN function operates normally, reset operations are complete. If abnormal, follow the
steps (e) to (g) below.
(e) Disconnect the negative battery terminal cable for 10 seconds.
(f) Connect the battery terminal cable.
(g) Perform the steps (a) to (d) again.

BE075±07
I28415
Door Lock Control Switch
Ignition SwitchDoor Lock Control Switch
Door Key Lock and Unlock
Switch

Back Door Control Switch Instrument Panel J/B
Body ECU
(Located behind the Instrument Panel)
Door Lock Assembly

Door Lock Motor

Door Key Lock and Unlock Switch

Door Unlock Detection Switch
Door Lock Assembly

Door Lock Motor

Door Unlock Detection Switch
Back Door Lock Assembly

Back Door Lock Motor

Back Door Detection Switch Back Door ECU
(Located inside of the back door trim board)
Door Lock Assembly

Door Lock Motor

Door Unlock Detection Switch
BE±78
± BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
3482 Author: Date:
2005 SEQUOIA (RM1146U)
POWER DOOR LOCK CONTROL SYSTEM
LOCATION

BE266±05
I18691
LOCK
UNLOCK
I18692
LOCK
UNLOCK
I18693
LOCKUNLOCK
I18694
LOCK UNLOCK
I18695
LOCKUNLOCKRight Side
Left Side
± BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
BE±79
3483 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT DRIVER DOOR KEY LOCK AND UNLOCK
SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK3 ± 5Continuity
OFF±No continuity
UNLOCK3 ± 6Continuity
If continuity is not as specified, replace the door lock motor.
2. INSPECT PASSENGER'S DOOR KEY LOCK AND UN-
LOCK SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK2 ± 4Continuity
OFF±No continuity
UNLOCK1 ± 4Continuity
If continuity is not as specified, replace the door lock motor.
3. INSPECT DRIVER'S DOOR UNLOCK DETECTION
SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)±No continuity
ON (Door Lock set to
UNLOCK)3 ± 4Continuity
If continuity is not as specified, replace the door lock motor.
4. INSPECT PASSENGER'S DOOR UNLOCK DETEC-
TION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)±No continuity
ON (Door Lock set to
UNLOCK)3 ± 4Continuity
If continuity is not as specified, replace the door lock motor.
5. INSPECT REAR DOOR UNLOCK DETECTION
SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)±No continuity
ON (Door Lock set to
UNLOCK)3 ± 4 (Left side)
1 ± 2 (Right side)Continuity
If continuity is not as specified, replace the door lock motor.

I18696
UNLOCK
LOCK
I18690
2
1UNLOCKLOCK
3
± BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
BE±81
3485 Author: Date:
2005 SEQUOIA (RM1146U)
11. INSPECT BACK DOOR UNLOCK DETECTION
SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)±No continuity
ON (Door Lock set to
UNLOCK)1 ± 2Continuity
If continuity is not as specified, replace the back door lock mo-
tor.
12. INSPECT BACK DOOR KEY LOCK AND UNLOCK
SWITCH CONTINUITY (Back Door Control switch)
Switch positionTester connectionSpecified condition
LOCK1 ± 3Continuity
OFF±No continuity
UNLOCK2 ± 3Continuity
If continuity is not as specified, replace the switch.