2001 TOYOTA SEQUOIA solenoid

DIDIY±01
D14145
E8E7E6E5E4
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±559
753 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECM
1. ECM
HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under ºConditionº. Look under ºSymbols (Terminal No.)º for the termi-
nals to be inspected. The standard voltage between the terminals is shown under ºSpecific Conditionº.
Use the illustration above as a reference for the ECM terminals.
Symbols (Terminals No.)Wiring ColorTerminal DescriptionConditionSpecified Condition
LMS (E5±9) ± E1 (E6±1)P±L ± BRL shift position switch sig-
nalIG switch ON10 to 14 V
===IG switch ON and Press continu-
ously shift position L switchBelow 1 V
2 (E5±10) ± E1 (E6±1)L ± BR2 shift position switch sig-
nalIG switch ON and shift lever 2 and L
position10 to 14 V
===IG switch ON and shift lever except
2 and L positionBelow 1 V
R (E5±11) ± E1 (E6±1)B±Y ± BRR shift position switch sig-
nalIG switch ON and shift lever R posi-
tion10 to 14 V
===IG switch ON and shift lever except
R positionBelow 1 V
D (E5±21) ± E1 (E6±1)W±R ± BRD shift position switch sig-
nalIG switch ON and shift lever D and
4 position10 to 14 V
===IG switch ON and shift lever except
D and 4 positionBelow 1 V
3 (E5±19) ± E1 (E6±1)L ± BR3 shift position switch sig-
nalIG switch ON and shift lever 3 posi-
tion10 to 14 V
===IG switch ON and shift lever except
3 positionBelow 1 V
ODMS (E4±12) ± E1 (E6±1)L±W ± BRO/D main switch signalIG switch ON10 to 14 V
===IG switch ON and press continu-
ously O/D main switchBelow 1 V
STP (E4±15) ± E1 (E6±1)G±Y ± BRStop lamp switch signalBrake pedal is depressed7.5 to 14 V
===Brake pedal is releasedBelow 1.5 V
SLU+ (E7±15) ± SLU± (E7±14)P±L ± L±WSLU solenoid signal5th (lock±up) gearPulse generation
(See waveform 2)
S2 (E7±10) ± E1 (E6±1)W±L ± BRS2 solenoid signal2nd or 3rd gear10 to 14 V
===1st, 4th or 5th gearBelow 1 V
S1 (E7±11) ± E1 (E6±1)R ± BRS1 solenoid signal1st or 2nd gear10 to 14 V
===3rd, 4th or 5th gearBelow 1 V

D14146
5 V/DIV
1 ms/DIVGND
D14147
GND
5 V/DIV
1 ms/DIV
DI±560
± DIAGNOSTICSAUTOMATIC TRANSMISSION
754 Author: Date:
2005 SEQUOIA (RM1146U)SLT+ (E7±13) ± SLT± (E7±12)
B±R ± G±YSLT solenoid signalEngine idle speedPulse generation
(See waveform 1)
SR (E7±9) ± E1 (E6±1)G±R ± BRSR solenoid signal5th gear10 to 14 V
===1st gearBelow 1 V
SL2+ (E7±17) ± SL2± (E7±16)GR ± LG±BSL2 solenoid signalEngine idle speedPulse generation
(See waveform 3)
SL1+ (E7±19) ± SL1± (E7±18)R±B ± LSL1 solenoid signalEngine idle speedPulse generation
(See waveform 4)
THO1 (E7±24) ± E2 (E8±28)G ± G±WNo.1 ATF temperature
sensor signalNo.1 ATF temperature: 115
C (239

F) or moreBelow 1.5 V
THO2 (E7±32) ± E2 (E8±28)V ± G±WNo.2 ATF temperature
sensor signalNo.2 ATF temperature: 115
C (239

F) or moreBelow 1.5 V
SP2+ (E7±34) ± SP2± (E7±26)W±R ± Y±RSpeed sensor (SP2) sig-
nalVehicle speed 20 km/h (12 mph)Pulse generation
(See waveform 6)
NT+ (E7±35) ± NT± (E7±27)B ± WSpeed sensor (NT) signalEngine idle speedPulse generation
(See waveform 5)
STAR/NSW (E7±8) ± E1 (E6±1)B ± BRPark neutral switch signalIG switch ON and shift lever P and
N positionBelow 2 V
===IG switch ON and shift lever except
P and N position10 to 14 V
L4* (E6±13) ± E1 (E6±1)L±R ± BRTransfer L position switch
signalIG switch ON and transfer L posi-
tionBelow 1 V
===IG switch ON and transfer except L
position10 to 14 V
HINT:
*: 4WD
Waveform 1
Reference:
TerminalSLT+ ± SLT±
Tool setting5V/DIV, 1ms/DIV
Vehicle conditionEngine idle speed
Waveform 2
Reference:
TerminalSLU+ ± SLU±
Tool setting5V/DIV, 1ms/DIV
Vehicle condition5th (lock±up) or 6th (lock±up) gear

DIDJ2±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±567
761 Author: Date:
2005 SEQUOIA (RM1146U)
FAIL±SAFE CHART
1. FAIL±SAFE
This function minimizes the loss of the ECT functions when any malfunction occurs in a sensor or solenoid.
Malfunction PartFunction
Output Speed Sensor (SP2)During an output speed sensor malfunction, shift control is effected through the
input speed sensor signal (NT).
ATF Temp. Sensor No. 1During an ATF temperature sensor No. 1 malfunction, up±shift to the 5th and flex
lock±up clutch control are prohibited.
Shift Solenoid Valve S1, S2 and SR
The current to the failed solenoid valve is cut off and control is effected by operating
the other solenoid valves with normal operation.
Shift control is effected depending on the failed solenoid as described in the table
on the next page.
Shift Solenoid Valve SL1 and SL2During a solenoid valve SL1 or SL2 malfunction, up±shift to the 5th is prohibited.
Shift Solenoid Valve SLU
During a solenoid valve SLU malfunction, the current to the solenoid valve is
stopped. This stops lock±up control and flex lock±up control, fuel economy de-
creases.
Shift Solenoid Valve SLT
During a solenoid valve SLT malfunction, the current to the solenoid valve is
stopped. This stops line pressure optimal control, the shift shock increases. How-
ever, shifting is effected through normal clutch pressure control.
Fail Safe Function:
If either of the shift solenoid valve circuits has an open or short failure, the ECM turns the other shift solenoid
ºONº and ºOFFº in order to shift into the gear positions shown in the table below.
In case of a short circuit, the ECM stops sending current to the short circuited solenoid.
Even if starting the engine again in the fail±safe mode, the gear position remains in the same position.

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±571
765 Author: Date:
2005 SEQUOIA (RM1146U)LOCK UP SOL
Lock Up Solenoid Status/
ON or OFF
Lock Up: ON

Except Lock Up: OFF±
SOLENOID (SLT)Shift Solenoid SLT Status/
ON or OFF

Accelerator pedal is depressed:
OFF

Accelerator pedal is released:
ON
±
SOLENOID (SLU)Shift Solenoid SLU Status/
ON or OFF
Lock Up: ON

Except Lock Up: OFF±
AT FLUID TEMP 1
ATF Temp. Sensor No.1 Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature
when cold soakIf the value is º±40C (±40F)º or
º215C (419F)º, ATF temp. sen-
sor No.1 circuit is open or shorted.
AT FLUID TEMP 2
ATF Temp. Sensor No.2 Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature
when cold soakIf the value is º±40C (±40F)º or
º215C (419F)º, ATF temp. sen-
sor No.2 circuit is open or shorted.
SPD (SP2)
Output shaft Speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)Vehicle stopped: 0 km/h (0 mph)
[HINT]
Equal to vehicle speed
±
SPD (NT)Input Turbine Speed/
display: 50 r/min
[HINT]

Lock±up ON (After warming up
the engine);
Input Turbine speed (NT) equal to
the engine speed.

Lock±up OFF (Idling at N posi-
tion);
Input Turbine speed (NT) nearly
equal to the engine speed.
±

DI±572
± DIAGNOSTICSAUTOMATIC TRANSMISSION
766 Author: Date:
2005 SEQUOIA (RM1146U)
2. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press º"º button: Shift up

Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
LOCK UP
[Test Details]
Control the shift solenoid SLU to set the automatic transmission to the
lock±up condition.
[Vehicle Condition]

Throttle valve opening angle: Less than 35 %

Vehicle Speed: 60 km/h (37 mph) or more
Possible to check the SLU opera-
tion.
LINE PRESS UP *
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]

Vehicle Stopped.

IDL: ON
[HINT]
OFF: Line pressure up (When the active test of ºControl the Line Pres-
sure Upº is performed, the ECM commands the SLT solenoid to turn
off).
ON: No action (normal operation)
±
*: ºLINE PRESS UPº in the ACTIVE TEST is performed to check the line pressure changes by connecting
the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (See page DI±540) as well.
HINT:
The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

DIDJ4±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±573
767 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the page
given.
HINT:
*1 :
... The MIL (Malfunction Indicator Lamp) lights up
*2 :  ... The ECM memorizes the trouble code if the ECM detects the DTC detection condition.
This DTC may be output when the clutch, brake and gear components etc. inside the automatic trans-
mission are damaged.
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory *2
P0500
(DI±278)Vehicle Speed Sensor ºAº
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM


P0705
(DI±576)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)Open or short in park/neutral position switch circuit
Park/neutral position switch
ECM


P0710
(DI±582)Transmission Fluid Temperature
Sensor ºAº CircuitOpen or short in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0711
(DI±588)Transmission Fluid Temperature
Sensor ºAº PerformanceTransmission wire (ATF temperature sensor No.1)

P0712
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit Low InputShort in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0713
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit High InputOpen in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0717
(DI±591)Input Speed Sensor Circuit No
Signal
Open or short in speed sensor (NT) circuit
Speed sensor (NT)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0722
(DI±596)Output Speed Sensor Circuit No
Signal
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0724
(DI±600)Brake Switch ºBº Circuit High
Short in stop light switch signal circuit
Stop light switch
ECM


P0748
(DI±603)Pressure Control Solenoid ºAº
Electrical
(Shift Solenoid Valve SL1)Open or short in shift solenoid valve SL1 circuit
Shift solenoid valve SL1
ECM


P0751
(DI±608)Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)Shift solenoid valve S1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0756
(DI±614)Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)Shift solenoid valve S2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0771
(DI±620)Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
Shift solenoid valve SR remains open or closed
Shift solenoid valve SL1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)



DI±574
± DIAGNOSTICSAUTOMATIC TRANSMISSION
768 Author: Date:
2005 SEQUOIA (RM1146U)P0776
(DI±625)
Pressure Control Solenoid ºBº
Performance
(Shift Solenoid Valve SL2)Shift solenoid valve SL2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0778
(DI±631)Pressure Control Solenoid ºBº
Electrical
(Shift Solenoid Valve SL2)Open or short in shift solenoid valve SL2 circuit
Shift solenoid valve SL2
ECM


P0781
(DI±636)1±2 Shift (1 ±2 Shift Valve)Valve body is blocked up or stuck (1±2 shift valve)
Automatic transmission (clutch, brake or gear, etc.)

P0973
(DI±641)Shift Solenoid ºAº Control Circuit
Low (Shift Solenoid Valve S1)Short in shift solenoid valve S1 circuit
Shift solenoid valve S1
ECM


P0974
(DI±641)Shift Solenoid ºAº Control Circuit
High (Shift Solenoid Valve S1)Open in shift solenoid valve S1 circuit
Shift solenoid valve S1
ECM


P0976
(DI±646)Shift Solenoid ºBº Control Circuit
Low (Shift Solenoid Valve S2)Short in shift solenoid valve S2 circuit
Shift solenoid valve S2
ECM


P0977
(DI±646)Shift Solenoid ºBº Control Circuit
High (Shift Solenoid Valve S2)Open in shift solenoid valve S2 circuit
Shift solenoid valve S2
ECM


P0985
(DI±651)Shift Solenoid ºEº Control Circuit
Low (Shift Solenoid Valve SR)Short in shift solenoid valve SR circuit
Shift solenoid valve SR
ECM


P0986
(DI±651)Shift Solenoid ºEº Control Circuit
High (Shift Solenoid Valve SR)Open in shift solenoid valve SR circuit
Shift solenoid valve SR
ECM


P2714
(DI±656)Pressure Control Solenoid ºDº
Performance
(Shift Solenoid Valve SLT)Shift solenoid valve SLT remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P2716
(DI±662)Pressure Control Solenoid ºDº
Electrical
(Shift Solenoid Valve SLT)Open or short in shift solenoid valve SLT circuit
Shift solenoid valve SLT
ECM


P2740
(DI±666)Transmission Fluid Temperature
Sensor ºBº CircuitOpen or short in ATF temperature sensor No.2 circuit
Transmission wire (ATF temperature sensor No.2)
ECM


P2742
(DI±666)Transmission Fluid Temperature
Sensor ºBº Circuit Low InputShort in ATF temperature sensor No.2 circuit
Transmission wire (ATF temperature sensor No.2)
ECM


P2743
(DI±666)Transmission Fluid Temperature
Sensor ºBº Circuit High InputOpen in ATF temperature sensor No.2 circuit
Transmission wire (ATF temperature sensor No.2)
ECM


P2757
(DI±672)
Torque Converter Clutch Pres-
sure Control Solenoid Perfor-
mance
(Shift Solenoid Valve SLU)Shift solenoid valve SLU remains open or closed
Valve body is blocked
Torque converter clutch
Automatic transmission (clutch, brake or gear, etc.)
Line pressure is too low


P2759
(DI±680)
Torque Converter Clutch Pres-
sure Control Solenoid Control
Circuit Electrical
(Shift Solenoid Valve SLU)Open or short in shift solenoid valve SLU circuit
Shift solenoid valve SLU
ECM



D14157
O E1 Electronically Controlled
Transmission Solenoid
OT±O
OT+
L
OT2±L
OT2+ G±W
G±W
G±WG
B±L
G±W 2
110
9E7
E7
E828 32 24
THO2 THO1
E2ECM
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±585
779 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
AT FLUID TEMP 1
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature when cold soak
HINT:
When DTC P0712 is output and hand±held tester output is 150C (302F) or more, there is a short circuit.
When DTC P0713 is output and hand±held tester output is ±40C (±40F), there is an open circuit.
Measure the resistance between terminal THO1 (OT) and body ground.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
150°C (302°F) or moreShort circuit
HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 second).
When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.