2001 TOYOTA SEQUOIA fuel

DID7O±02
± DIAGNOSTICSENGINE
DI±3
197 Author: Date:
2005 SEQUOIA (RM1146U)
TOYOTA PART AND SYSTEM NAME LIST
This reference list indicates the part names used in this manual along with their definitions.
TOYOTA/LEXUS nameDefinition
Toyota HCAC system, Hydro±carbon Adsorptive Catalyst
(HCAC) system, HC adsorptive three±way catalystHC adsorptive three±way catalytic converter
Variable Valve Timing sensor, VVT sensorCamshaft position sensor
Variable valve timing system, VVT systemCamshaft timing control system
Camshaft timing oil control valve, Oil control valve, OCV,
VVT, VSVCamshaft timing oil control valve
Variable timing and lift, VVTLCamshaft timing and lift control
Crankshaft position sensor ºAºCrankshaft position sensor
Engine speed sensorCrankshaft position sensor
THAIntake air temperature
Knock control moduleEngine knock control module
Knock sensorEngine knock sensor
Mass or volume air flow circuitMass air flow sensor circuit
Vacuum sensorManifold air pressure sensor
Internal control module, Control module, Engine control
ECU, PCMPower train control module
FC idleDeceleration fuel cut
Idle air control valveIdle speed control
VSV for CCV, Canister close valve VSV for canister controlEvaporative emissions canister vent valve
VSV for EVAP, Vacuum switching valve assembly No. 1,
EVAP VSV, Purge VSVEvaporative emissions canister purge valve
VSV for pressure switching valve, Bypass VSVEvaporative emission pressure switching valve
Vapor pressure sensor, EVAP pressure sensor, Evaporative
emission control system pressure sensorFuel tank pressure sensor
Charcoal canisterEvaporative emissions canister
ORVR systemOn±board refueling vapor recovery system
Intake manifold runner controlIntake manifold tuning system
Intake manifold runner valve, IMRV, IACV (runner valve)Intake manifold tuning valve
Intake control VSVIntake manifold tuning solenoid valve
AFSAir fuel ratio sensor
O2 sensorHeater oxygen sensor
Oxygen sensor pumping current circuitOxygen sensor output signal
Oxygen sensor reference ground circuitOxygen sensor signal ground
Accel position sensorAccelerator pedal position sensor
Throttle actuator control motor, Actuator control motor, Elec-
tronic throttle motor, Throttle control motorElectronic throttle actuator
Electronic throttle control system, Throttle actuator control
systemElectronic throttle control system
Throttle/pedal position sensor, Throttle/pedal position switch,
Throttle position sensor/switchThrottle position sensor
Turbo press sensorTurbocharger pressure sensor
Turbo VSVTurbocharger pressure control solenoid valve
P/S pressure switchPower±steering pressure switch
VSV for ACMActive control engine mount

DID7P±01
B17433
Heated Oxygen Sensor
(Bank 2 Sensor 2) Fuel Pump
Resister
Knock Sensor 2
A/F Sensor
(Bank 1 Sensor 1) A/F Sensor
(Bank 2 Sensor 1)EVAP VSV
Combination Meter
Ignition Coil with Igniter
ECM Knock Sensor 1
Injector Throttle Body
(Throttle Position Sensor,
Throttle Control Motor)Mass Air Flow
Meter
Camshaft
Position Sensor
Crankshaft Position
SensorHeated Oxygen Sensor
(Bank 2 Sensor 2)
Park/Neutral Position
Switch DLC3
Air Injection Driver
(AID)
Accelerator Pedal Assembly
(Accelerator Pedal Position
Sensor)
Fuel Pump
VVT Sensor (Bank 2)
VVT Sensor (Bank 1) OCV (Bank 2)
OCV (Bank 1) Air Pump
Air Switching Valve No.2
(ASV No.2) (Bank 1)
Air Switching Valve
(ASV) Air Switching Valve No.2
(ASV No.2) (Bank 2)
VSV for Air Injection
Contorl (Bank 1)
VSV for Air Injection
Contorl (Bank 2)ACIS VSVCharcoal Canister Assembly
± DIAGNOSTICSENGINE
DI±5
199 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

B17430
HA1A
A1A+
A1A±
HA2A
A2A+
A2A±
HT1B
OXIB
HT2B
OX2B
E2
PRG
ACIS
AIV1
AIV2
THA
E2G
VG
E2
THW
PPMP
VPMP
MPMP#10
#20
#30
#40
#50
#60
#70
#80
IGT1
IGT2
IGT3
IGT4
IGT5
IGT6
IGT7
IGT8
IGF1
IGF2 To A/F Relay
A/F Sensor
(Bank 1 Sensor 1)
A/F Sensor
(Bank 2 Sensor 1)
HO2 Sensor
(Bank 1 Sensor 2)
HO2 Sensor
(Bank 2 Sensor 2) To EFI Relay
To EFI No.2
Fuse
VSV (EVAP)
VSV (ACIS)
VSV (AI Control)
VSV (AI Control)
Mass Air Flow
Meter
ETC Sensor
Pump Modul
Pressure
Sensor
Control
Valve To VC
TerminalTo Battery
IGN2
Fuel Injector #1
Fuel Injector #2
Fuel Injector #3
Fuel Injector #4
Fuel Injector #5
Fuel Injector #6
Fuel Injector #7
Fuel Injector #8
Ignition Coil and
Igniter No.1
Ignition Coil and
Igniter No.2
Ignition Coil and
Igniter No.3
Ignition Coil and
Igniter No.4
Ignition Coil and
Igniter No.5
Ignition Coil and
Igniter No.6
Ignition Coil and
Igniter No.7
Ignition Coil and
Igniter No.8
± DIAGNOSTICSENGINE
DI±7
201 Author: Date:
2005 SEQUOIA (RM1146U)

B17431
AIDI
AIRP
AIRV
AIP
GE01
M+
M±
VTA1
VC
VTA2
FC
FPRACCR
ST1±
STP
E01
E02
E04
E05
E1
E03
ME01
EC
EOM
TC
CANL
CANH
IMI
IMODLC3
CG
TC
CANL
CANH ASVAI Driver To EFI Relay
To Battery
To Battery
To Battery To E2
TerminalTo E2
TerminalTo IG SW
Air Pump
Pressure
Sensor
Throttle Body
C/OPN Relay
Fuel Pump Relay
Fuel Pump Resister
Fuel PumpTransponder Key
Computre Stop Light SW
To IGN1 Fuse
To EFI
RelayACC Cut Relay
To Battery DI±8
± DIAGNOSTICSENGINE
202 Author: Date:
2005 SEQUOIA (RM1146U)

± DIAGNOSTICSENGINE
DI±13
207 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check air filter.
PREPARATION:
Remove the air filter.
CHECK:
Visual check that the air filter is not excessively dirty or oily.
NG Repair or replace
air filter.
OK
5 Check idle speed (See page EM±11).
NG Proceed to problem symptoms table on page
DI±33.
OK
6 Check fuel pressure (See page SF±7).
NG Proceed to page SF±7 and continue to trouble-
shoot.
OK
7 Check for spark (See page IG±1).
NG Proceed to page IG±1 and continue to trouble-
shoot.
OK
Proceed to problem symptoms table on page
DI±33.

DICEL±02
± DIAGNOSTICSENGINE
DI±27
221 Author: Date:
2005 SEQUOIA (RM1146U)
READINESS MONITOR DRIVE PATTERN
1. PURPOSE OF THE READINESS TESTS

The On±Board Diagnostic (OBD II) system is designed to monitor the performance of emission±re-
lated components and report any detected abnormalities in the form of Diagnostic Trouble Codes
(DTCs). Since the various components need to be monitored during different driving conditions, the
OBD II system is designed to run separate monitoring programs called Readiness Monitors. Many
state Inspection and Maintenance (I/M) programs require that vehicles complete their Readiness Mon-
itors prior to beginning an emission test.

The current status of the Readiness Monitors can be seen by using the hand±held tester with version
9.0 software (or newer), or a generic OBD II Scan tool.

To view the Readiness Monitor status using the hand±held tester, select ºMonitor Statusº from the En-
hanced OBD II Menu.

A status of ºcompleteº indicates that the necessary conditions have been met to run the performance
tests for the related Readiness Monitor.

The Readiness Monitor will be reset to ºincompleteº if:

ECM has lost power (battery or fuse).

DTCs have been cleared.

The conditions for running the Readiness Monitor have not been met.

In the event that any Readiness Monitor shows ºincomplete,º follow the appropriate Readiness Monitor
Drive Pattern to activate the monitor and change the readiness status to ºcomplete.º
CAUTION:
Strictly observe the posted speed limits, traffic laws, and road conditions when performing these
drive patterns.
NOTICE:
These drive patterns represent the fastest method to satisfy all necessary conditions which allow
the specific readiness monitor to complete.
In the event that the drive pattern must be interrupted (possibly due to traffic conditions or other fac-
tors) the drive pattern can be resumed, and in most cases, the readiness monitor will still set to ºcom-
pleteº.
To ensure rapid completion of readiness monitors, avoid sudden changes in vehicle load and speed
(driving up and down hills and/or sudden acceleration).
Contents:
TITLESTEP(s)
CATALYST MONITOR2
EVAP MONITOR3, 4
AIR±FUEL RATIO (A/F) AND OXYGEN SENSOR (O2S) MONITOR5
OXYGEN SENOSR HEATER MONITOR6

A23510
Vehicle Speed
(64 km/h and 113 km/h)Between
40 mph and 70 mph
Idling
Ignition Switch OFF
10 minutes
Time Warm up
(Note: Even when vehicle stops during driving pattern, test can be resumed)NOTICE:
This test will not be completed
if the vehicle is driven under
absolute constant speed
condition such as with cruise
control activated. (6)
(5) DI±28
± DIAGNOSTICSENGINE
222 Author: Date:
2005 SEQUOIA (RM1146U)
2. CATALYST MONITOR (ACTIVE AIR±FUEL RATIO CONTROL TYPE)
(a) Preconditions
The monitor will not run unless:

The MIL is OFF
(b) Drive Pattern
(1) Connect a hand±held tester or OBD II scan tool to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the tester or scan tool ON.
(4) Clear DTCs (where set) (see page DI±43).
(5) Start the engine and warm it up.
(6) Drive the vehicle at between 40 mph and 70 mph (64 km/h and 113 km/h) for at least 10 minutes.
(c) Monitor Status
(1) Check the Readiness Monitor status displayed on the tester or scan tool.
(2) If the status does not switch to COMPL (complete), extend the driving time.

A18910
Idling
Ignition OFF
Warmed up Soak 15 to 50 min.
(When the readiness code or diagnostic code
is set, this test is completed.) 3,000 rpm
10 sec.
± DIAGNOSTICSENGINE
DI±29
223 Author: Date:
2005 SEQUOIA (RM1146U)
3. EVAP MONITOR (VACUUM PRESSURE MONITOR)
NOTICE:
A cold soak must be performed prior to conducting the drive pattern to complete the Internal Pres-
sure Readiness Monitor.
(a) Cold Soak Preconditions
The monitor will not run unless:

MIL is OFF

Fuel level is approximately 1/2 to 3/4

Altitude is 7,800 feet (2,400 m) or less
(b) Cold Soak Procedure
Let the vehicle cold soak for 8 hours or until the difference between IAT and ECT becomes less than
7°C (13°F)
HINT:
Examples:

Scenario 1
ECT = 24°C (75°F)
IAT = 16°C (60°F)
Difference between ECT and IAT is 8°C (15°F)
" The monitor will not run because difference between ECT and IAT is greater than 7°C (13°F)

Scenario 2
ECT = 21°C (70°F)
IAT = 20°C (68°F)
Difference between ECT and IAT is 1°C (2°F)
" The monitor will run because difference between ECT and IAT is less than 7°C (13°F)
4. EVAP MONITOR (VACUUM PRESSURE MONITOR) (CONTINUED)