2001 TOYOTA SEQUOIA service

H23966
Airbag
Sensor
Assembly
C DCurtain Shield
Airbag RH Squib
DI±1446
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1640 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check curtain shield airbag assembly RH (curtain shield airbag RH squib).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 11:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the curtain shield airbag as-
sembly RH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1830, B1831, B1832 or B1833 is not output.
HINT:
Codes other than DTC B1830, B1831, B1832 and B1833 may
be output at this time, but they are not related to this check.
NG Replace curtain shield airbag assembly RH
(see page RS±71).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01017H23982H23992
Airbag
Sensor
Assembly
ICL+ICL± D
C
Service Wire Curtain Shield
Airbag LH Squib
C11
DI±1456
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1650 Author: Date:
2005 SEQUOIA (RM1146U)
11 Check airbag sensor assembly.
PREPARATION:
(a) From the step 6:
Turn the ignition switch to the LOCK position.
(b) From the step 6:
Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Using a service wire, connect C11±1 (ICL+) and C11±2
(ICL±) of the connector ºCº.
NOTICE:

Twist the end of the service wire in order to insert it
into the connector.

Do not forcibly insert the twisted service wire into the
terminals of the connector when connecting.
(d) Connect the connectors to the airbag sensor assembly.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1836, B1837 or B1838 is not output.
HINT:
Codes other than DTC B1836, B1837 and B1838 may be out-
put at this time, but they are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK

H01018H23474
Curtain Shield
Airbag LH Squib
Airbag
Sensor
Assembly DC
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1457
1651 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check curtain shield airbag assembly LH (curtain shield airbag LH squib).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 9:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the curtain shield airbag as-
sembly LH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1835, B1836, B1837 or B1838 is not output.
HINT:
Codes other than DTC B1835, B1836, B1837 and B1838 may
be output at this time, but they are not related to this check.
NG Replace curtain shield airbag assembly LH
(see page RS±71).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01020H43107H23605
P/T Squib RH
PR± PR+
Floor Wire
Service Wire
C DAirbag
Sensor
Assembly
P11
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1467
1661 Author: Date:
2005 SEQUOIA (RM1146U)
11 Check airbag sensor assembly.
PREPARATION:
(a) From the step 6:
Turn the ignition switch to the LOCK position.
(b) From the step 6:
Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Connect the connectors to the airbag sensor assembly.
(d) Using a service wire, connect P11±1 (PR+) and P11±2
(PR±) of connector ºCº.
NOTICE:

Twist the end of the service wire in order to insert it
into the connector.

Do not forcibly insert the twisted service wire into the
terminals of the connector when connecting.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1901, B1902 or B1903 is not output.
HINT:
Codes other than DTC B1901, B1902 and B1903 may be out-
put at this time, but they are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK

H23966
Airbag
Sensor
Assembly
C D P/T Squib RH
DI±1468
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1662 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check front seat outer belt RH (P/T squib RH).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) From the step 11:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the front seat outer belt RH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1900, B1901, B1902 or B1903 is not output.
HINT:
Codes other than DTC B1900, B1901, B1902 and B1903 may
be output at this time, but they are not related to this check.
NG Replace front seat outer belt RH
(see page BO±163).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01017H43107H23603
Airbag
Sensor
Assembly P/T Squib LH
C D
PL± PL+
Service Wire
P10
DI±1478
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1672 Author: Date:
2005 SEQUOIA (RM1146U)
11 Check airbag sensor assembly.
PREPARATION:
(a) From the step 6:
Turn the ignition switch to the LOCK position.
(b) From the step 6:
Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Connect the connectors to the airbag sensor assembly.
(d) Using a service wire, connect P10±1 (PL+) and P10±2
(PL±) of connector ºCº.
NOTICE:

Twist the end of the service wire in order to insert it
into the connector.

Do not forcibly insert the twisted service wire into the
terminals of the connector when connecting.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1906, B1907 or B1908 is not output.
HINT:
Codes other than DTC B1906, B1907 and B1908 may be out-
put at this time, but they are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK

H01018H23474
Airbag
Sensor
Assembly DC P/T Squib LH
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1479
1673 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check front seat outer belt LH (P/T squib LH).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 10:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the front seat outer belt LH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1905, B1906, B1907 or B1908 is not output.
HINT:
Codes other than DTC B1905, B1906, B1907 and B1908 may
be output at this time, but they are not related to this check.
NG Replace front seat outer belt LH
(see page BO±163).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

A08841
Hand±held Tester
DLC3
DIDEZ±01
A04550
DLC3 1 2345678
9
10 11 12 1314 15 16
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1543
1737 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. DESCRIPTION
The ECM controls the cruise control system of the vehicle. The
data and DTCs relating to the cruise control system can be read
from the DLC3 of the vehicle. If no DTCs are output when
checking for DTCs, there may be a problem with the combina-
tion meter or the multiplex communication system.
Use the hand±held tester or SST to check and solve the prob-
lem.
SST 09843±18040
2. CHECK THE DLC3
The vehicle's ECM uses ISO 9141±2 for communication. The
terminal arrangement of the DLC3 complies with SAE J1962
and matches the ISO 9141±2 format.
Symbols (Terminals No.)Terminal DescriptionConditionSpecified Condition
SIL(7) ± SG(5)Bus º+º lineDuring transmissionPulse generation
CG(4) ± Body groundChassis groundAlwaysBelow 1 W
SG(5) ± Body groundSignal groundAlwaysBelow 1 W
BAT(16) ± Body groundBattery positiveAlways11 to 14 V
HINT:
If the display shows ºUNABLE TO CONNECT TO VEHICLEº af-
ter connecting the hand±held tester to the DLC3, turning the
ignition switch to the ON position and operating the tester, there
is a problem on either the vehicle side or the tool side.

If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.

If communication is still impossible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.