2001 TOYOTA SEQUOIA airbag

H23996
LA
A2014
ABR I18
Ignition SW
Combination Meter
BatteryIG2 A2021
E1 A2025
E2 A2026 B
W±B
W±B B±R
IG2 AM26 5 W±R
SRS B±Y
C5 29
C612 C6241D4
1A5 1A3 IGN1
1D6
1F9
101A6
1A8 Instrument Panel J/B
Engine Room J/B1H11
1J7
2C1
2D1AM2BR
W±B
W±B
J8
J/C A
A 4
5 B
BB±O
IEAirbag Sensor
Assembly
1C2
Instrument Panel J/B
F10
Fusible Link Block 1C3 D6
DLC3
114B10
4A20
4A10B±Y
B±Y
1F W±R Sub J/B No. 4 DI±1248
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1442 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1249
1443 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check battery.
CHECK:
Measure the voltage of the battery.
OK:
Voltage: 11 to 14 V
NG Replace battery.
OK
2 Check connection of connectors.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check that the connectors are properly connected to the airbag sensor assembly and combination meter.
OK:
The connectors are connected securely.
NG Connect connectors, then go to step 1.
OK
3 Check combination meter.
PREPARATION:
(a) Disconnect the connectors from the airbag sensor assembly.
(b) Connect the negative (±) terminal cable to the battery, and wait for at least 2 seconds.
CHECK:
Turn the ignition switch to the ON position, check the operation of the SRS warning light.
OK:
The SRS warning light comes on (goes off 6 seconds after the ignition switch is turned to the
ON position).
NG Go to combination meter system
(see page DI±1610).
OK

H22564H23040I27704H23986
A Cowl Wire Combination
Meter
C5
A20
Airbag
Sensor
Assembly
B C D
C5±29LA
DI±1250
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1444 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check cowl wire (airbag sensor assembly ± combination meter).
PREPARATION:
Disconnect the connector from the combination meter.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±14 (LA) ± C5±29AlwaysBelow 1 W
A20±14 (LA) ±
Body groundAlways1 MW or higher
NG Repair or replace cowl wire.
OK
Replace airbag sensor assembly (see page RS±82).

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1253
1447 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:

If troubleshooting (wire harness inspection) is difficult to perform, remove the passenger seat installa-
tion bolts to see the under surface of seat cushion.

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time
may cause a problem, such as seat rail deformation. Hold the seat only as necessary.
1 Check DTC.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in memory (see page DI±1147).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand±held tester, check the DTCs of the occupant classification ECU (see page DI±1147).
OK:
DTC B1771 is not output.
HINT:
Codes other than DTC B1771 may be output at this time, but they are not related to this check.
NG Go to step 2.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1257
1451 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check DTC.
PREPARATION:
(a) Connect the connectors to the occupant classification ECU and the front seat inner belt RH.
(b) Connect the negative (±) terminal cable to the battery.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in memory (see page DI±1147).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand±held tester, check the DTCs of the occupant classification ECU (see page DI±1147).
OK:
DTC B1771 is not output.
HINT:
Codes other than DTC B1771 may be output at this time, but they are not related to this check.
NG Go to step 8.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).

DI±1258
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1452 Author: Date:
2005 SEQUOIA (RM1146U)
8 Replace front seat inner belt RH.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the front seat inner belt RH (see page BO±112, BO±126).
HINT:
Perform the inspection using parts from a normal vehicle if possible.
(d) Connect the negative (±) terminal cable to the battery.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in memory (see page DI±1147).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand±held tester, check the DTCs of the occupant classification ECU (see page DI±1147).
OK:
DTC B1771 is not output.
HINT:
Codes other than DTC B1771 may be output at this time, but they are not related to this check.
NG Go to step 9.
OK
END

DI±1262
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1456 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:

If troubleshooting (wire harness inspection) is difficult to perform, remove the passenger seat installa-
tion bolts to see the under surface of seat cushion.

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time
may cause a problem, such as seat rail deformation. Hold the seat only as necessary.
1 Check DTC.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in memory (see page DI±1147).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand±held tester, check the DTCs of the occupant classification ECU (see page DI±1147).
OK:
DTC B1780 is not output.
HINT:
Codes other than DTC B1780 may be output at this time, but they are not related to this check.
NG Go to step 2.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).

DI±1266
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1460 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check DTC.
PREPARATION:
(a) Connect the connectors to the occupant classification ECU and the occupant classification sensor
front LH.
(b) Connect the negative (±) terminal cable to the battery.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in memory (see page DI±1147).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand±held tester, check the DTCs of the occupant classification ECU (see page DI±1147).
OK:
DTC B1780 is not output.
HINT:
Codes other than DTC B1780 may be output at this time, but they are not related to this check.
NG Go to step 8.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).