Page 1123 of 4323
DI93C±06
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±921
111 5 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
NOTICE:
When removing parts, turn the ignition switch OFF.
When replacing the master cylinder, yaw rate and deceleration sensors and/or the ECU, make
sure to perform master cylinder, yaw rate and deceleration sensors' zero point calibration (See
page DI±897).
HINT:
Using SST 09843±18040, connect terminals Tc and CG.
If no abnormality is found when inspecting parts, inspect the ECU.
If a trouble code is displayed during the DTC check, check the circuit listed for that code. For details
of each code, turn to the page referred to under the ºSee pageº for respective ºDTC No.º in the DTC
chart.
DTC chart of ABS system:
DTC No.
(See Page)Detection ItemTrouble Area
C0200/31*1
(DI±925)Right front wheel speed sensor signal malfunction
C0205/32*1
(DI±925)Left front wheel speed sensor signal malfunctionRight front, left front, right rear and left rear speed sensor
Each speed sensor circuit
C0210/33*1
(DI±925)Right rear wheel speed sensor signal malfunction
Each s eed sensor circuit
Speed sensor rotor
Skid control ECU
C0215/34*1
(DI±925)Left rear wheel speed sensor signal malfunction
C0226/21
(DI±932)Malfunction in ABS & VSC solenoid valvesABS & VSC actuator
ABS & VSC solenoid circuit
C0278/11
(DI±934)Open or short circuit in ABS & VSC relay circuit
ABS & VSC solenoid relay
ABS & VSC solenoid relay circuit
ABS & VSC motor relay
ABS & VSC motor relay circuit
C1241/41
(DI±957)Low battery positive voltage or abnormally high battery positive
voltage
Battery
Charging system
Power source circuit (+BM, +BS)
Skid control ECU
C1244/44
(DI±951)Open or short circuit in deceleration sensor circuitYaw rate (deceleration) sensor
Yaw rate (deceleration) sensor circuit
C1247/47
(DI±960)Malfunction in delta S sensor
Delta S sensor
Delta S sensor circuit
Skid control ECU
Brake booster
C1249/49
(DI±963)Open circuit in stop light switch circuit
Stop light switch
Stop light switch circuit
Skid control ECU
C1251/51*1
(DI±966)
Pump motor is locked
Open circuit in pump motor circuitABS & VSC actuator
C1337/37
(DI±975)Some tires are different in size from the other tiresTire size
Always ON
(DI±1016)Malfunction in skid control ECU
Battery
Charging system
Power source circuit
ABS warning light circuit
Skid control ECU
Page 1124 of 4323
DI±922
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
111 6 Author: Date:
2005 SEQUOIA (RM1146U)
*1: As long as the following operations are not performed, the ABS warning light will not go OFF only by re-
pairing the trouble area.
(1) Drive the vehicle at 12 mph (20 km/h) for 30 seconds or more and check that the ABS warning light goes
off.
(2) Clear the DTC (See page DI±911).
HINT:
There is a possibility that the hand±held tester cannot be used when the ABS warning light is always ON.
DTC chart of VSC system:
DTC No.
(See Page)Detection ItemTrouble Area
C1201/51
(DI±936)Engine control system malfunctionEngine control system
C1202/52
(DI±937)Brake fluid level warning switch circuit
Brake fluid level
Brake fluid level warning switch
Brake fluid level warning switch circuit
Skid control ECU
CAN1 communication system
Translate ECU
C1203/53 *1
(DI±942)Malfunction in CAN1 communication
Skid control ECU
CAN1 communication system
ECM
Translate ECU
C1207/37
(DI±522)Reverse gear signal failureECT
C1223/43
(DI±945)Malfunction in ABS control systemABS control system
C1231/31
(DI±946)Malfunction in steering angle sensor
Steering angle sensor
Steering angle sensor communication circuit
Skid control ECU
Translate ECU
CAN communication system
C1232/32
(DI±951)Malfunction in deceleration sensorYaw rate (deceleration) sensor
Yaw rate (deceleration) sensor circuit
C1234/34
(DI±954)Malfunction in yaw rate sensorYaw rate (deceleration) sensor
Yaw rate (deceleration) sensor circuit
C1310/11
(DI±969)Open or short circuit in active brake booster solenoid circuitBrake booster
Active brake booster solenoid circuit
C1311/12
(DI±971)Open or short circuit in brake inhibit relay circuitBrake inhibit relay
Brake inhibit relay circuit
1335/35
(DI±946)Malfunction in steering angle sensor communication circuit
Steering angle sensor
Steering angle sensor communication circuit
Skid control ECU
Translate ECU
CAN1 communication system
C1340/47*2
(DI±977)Center diff. lock circuit malfunction
Center diff. lock position switch
Center diff. lock position switch circuit
Center diff. lock indicator light circuit
Translate ECU
C1360/61
(DI±983)Malfunction in master cylinder pressure sensorMaster cylinder pressure sensor
Master cylinder pressure sensor circuit
Page 1125 of 4323
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±923
111 7 Author: Date:
2005 SEQUOIA (RM1146U)C1361/62
(DI±986)
Abnormal battery voltage of VSC sensor
Battery
Charging system
Power source circuit
Yaw rate (deceleration) sensor
Skid control ECU
Master cylinder pressure sensor
C1362/36
(DI±990)Malfunction in sensor offset value (VSC sensor system)Skid control ECU
(Perform zero point calibration)
C1363/63
(DI±991)Malfunction in booster pedal force switchBooster pedal force switch (Active brake booster)
Booster pedal force switch (Active brake booster) circuit
U0100/65
(DI±1075)Malfunction in vehicle CAN communication systemVehicle CAN communication system
HINT:
There is a possibility that the hand±held tester cannot be used when the VSC TRAC warning light is always
ON.
*
1: Check DTC chart C1203/53 first, then troubleshoot according to the DTC chart of translate ECU if neces-
sary.
*
2:
4WD
DTC chart of translate ECU (When DTC ºC1201/51, C1202/52, C1203/53 or U0100/65º of VSC system
is output):
DTC No.
(See Page)Detection ItemTrouble Area
Normal code*
(DI±1013)Malfunction in ECM control system or suspension control ECU
ECM circuit
ECM
Brake fluid level
Brake fluid level warning switch circuit
Steering angle sensor
Translate ECU
Skid control ECU
Vehicle CAN
VSC+, VSC± circuit (CAN1 communication system)
51
(DI±995)Malfunction in ECM control systemECM
53
(DI±998)Malfunction in CAN1 communication
VSC+, VSC± circuit (CAN1 communication system)
Skid control ECU
Translate ECU
58
(DI±1002)Malfunction of brake fluid level switch
Brake fluid level warning switch circuit
Brake fluid level warning switch
Brake fluid reservoir level
Translate ECU
65
(DI±1005)Malfunction 1 of vehicle CAN
ENG+, ENG± circuit (CAN communication system)
ECM
Translate ECU
Suspension control ECU
94
(DI±1009)Malfunction 2 of vehicle CAN
ENG+, ENG± circuit (CAN communication system)
ECM
Translate ECU
Suspension control ECU
Non±code
(DI±1015)Malfunction in translate ECU
Brake warning light circuit
Tc terminal circuit
Translate ECU
*: Translate ECU is normal.
Page 1126 of 4323
DI±924
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
111 8 Author: Date:
2005 SEQUOIA (RM1146U)
If the brake warning light turns on, check that the parking brake pedal is released, the brake fluid level is
normal, and no malfunction is identified in the fluid level warning switch system.
If there is a problem with VSC, the brake warning light comes on. The possible causes of a problem are as
follows:
2 or more wheel speed sensor failures
Low/high voltage
Valve failure
Page 1139 of 4323
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±937
1131 Author: Date:
2005 SEQUOIA (RM1146U)
DTC C1202 / 52 Brake Fluid Warning Switch Circuit
CIRCUIT DESCRIPTION
The brake fluid level warning switch sends the appropriate signal to the skid control ECU when the brake
fluid level drops.
A brake fluid level signal is transmitted from the translate ECU to the skid control ECU.
DTC No.DTC Detecting ConditionTrouble Area
C1202 / 52
When any of the following conditions are detected:
1. Low fluid level condition in the brake master cylinder
reservoir tank continues for 30 sec. or more when ve-
hicle stops, or for 60 sec. or more when driving.
2. With ECU terminal IG1 voltage is 9.5 V to 17.2 V and
open circuit for the brake fluid level warning switch cir-
cuit continues for 2 sec. or more.Brake fluid level
Brake fluid level warning switch
Brake fluid level warning switch circuit
Skid control ECU
CAN1 communication system
Translate ECU
DIDM7±01
Page 1140 of 4323
F19769
Translate ECU
VSC+
VSC±
IG17
T5
T511
1
T5B±RL
W
AA
J37
J38
A
J37B±R J/C
B±R B±RL
W 7
IL2
6
IL2
1
IL16
S1
2
S1
13
S1 ABS &VSC Actuator
(Skid Control ECU)
CANH
CANL
IG1
8
3C8
3A
B±R Instrument Panel J/B
4
1C
2
1C
3
1C
6
1C4
1F
11
1H
7
1J
1
1L ECU±IG
IGN1
AM1 B±R B±Y
W±R
W±LB±O
W±R
W
1 2Combination Meter
24
C6
Brake
1C5 W
8
ALTF10 Fusible
Link BlockEngine Room J/B
A W±R 1
2D1
2C
4
5
R±B R±B
B1 Brake Fluid Level
Warning SW
Y±L Y±LW±B 23
IA1
129
IA5O
A
A O
OJ43
J/C
IG Sub J/B No.4
LG±R
LG±R 4
4B4
4D
1P2 Parking
Brake SW
B
Battery 39
T5
24
T5
40
T5
4
T5 BRL
LVL2
GND
PKB2Sub J/B No.3
I18
Ignition SW
AM1 IG1
AM2 IG2 1
5 W±L
2
6
AM2
BB±R (CAN1 Circuit)
(CAN1 Circuit) DI±938
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1132 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Page 1141 of 4323
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±939
1133 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check brake fluid level.
CHECK:
Check the amount of fluid in the brake reservoir.
NG Check and repair brake fluid leakage and add
fluid.
OK
2 Check DTC of translate ECU (translate DTC 58).
CHECK:
Check DTC of the translate ECU (See page DI±911).
RESULT:
DTC 58 is not outputA
DTC 58 is outputB
B Go to step 4.
A
3 Check for open and short circuit in harness and connector between skid control
ECU and translate ECU (CAN1 circuit).
NG Repair or replace harness or connector
(CAN1 circuit).
OK
Replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform zero point calibration (See page DI±897).
Page 1142 of 4323
F18069
DI±940
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1134 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check brake fluid level warning switch.
PREPARATION:
Disconnect the brake fluid level warning switch connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSwitch ConditionSpecified Condition
(B2±1) ± (B2±2)Float UP10 kW or more
(No continuity)
(B2±1) ± (B2±2)Float DOWN1 W or less (Continuity)
NG Replace brake reservoir tank.
OK
5 Check for open and short circuit in harness and connector between brake fluid
level warning switch and translate ECU (See page IN±35).
NG Repair or replace harness or connector.
OK
