2001 TOYOTA SEQUOIA engine

DI±1986
± DIAGNOSTICSAUDIO SYSTEM
2180 Author: Date:
2005 SEQUOIA (RM1146U)
3. Multi±display controller sub±assy (Physical address: 1F6) [RSE ECU, MAIN]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
21ROM ErrorAbnormal condition of ROM is detected.Replace multi±display controller
sub±assy.±
22ROM ErrorAbnormal condition of RAM is detected.Replace multi±display controller
sub±assy.±
D1
*1
Registered component discon-
nected
AVC±LAN transmitting abnor-
malitiesComponent shown by sub±code is or was discon-
nected from system with ignition switch in ACC or
ON.
Communication with component shown by sub±
code is not ensured when engine is started.
1. Power source circuit (Multi±dis-
play controller sub±assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±2110
DI±2139
±
D7
*2No response to connection
checkComponent shown by sub±code is or was discon-
nected from system after engine started.
1. Power source circuit (Multi±dis-
play controller sub±assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±2110
DI±2139
±
D7
*2AVC±LAN Communication
Check Error
Component in which this code is recorded is or
was disconnected from system after engine start.
Or, when recording this code, multi±display con-
troller was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
4. Replace Multi±display controller
sub±assy.DI±1990
DI±2110
DI±2139
±
D6
*1Absence of Master
Component in which this code is recorded has
been disconnected from system with ignition in
ACC or ON. Or, when this code was recorded,
multi±display controller was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±
D7
*2Connection Check Error
Component in which this code is recorded has
been disconnected from system after engine start.
Or, when this code was recorded, multi±display
controller was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±
DC
*3Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DD
*4Master Reset (Momentary Inter-
ruption)Component that is to be master has been discon-
nected after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±

± DIAGNOSTICSAUDIO SYSTEM
DI±1987
2181 Author: Date:
2005 SEQUOIA (RM1146U)E0
*1
Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Request command is output from
sub±master component.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting an engine.

*2: This code is stored when 180 sec. has passed after the power supply connector is pulled out after
engine start.

*3: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position in 1 minute after engine start.

*4: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position after engine start.
Rear seat audio controller (Physical address: 1F4) [RSA]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D6
*1Absence of Master
Component in which this code is recorded has
been disconnected from system with ignition in
ACC or ON. Or, when this code was recorded,
RSA panel was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
D7
*2Connection Check Error
Component in which this code is recorded has
been disconnected from system after engine start.
Or, when this code was recorded, RSA panel was
disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DC
*3Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DD
*4Master Reset (Momentary Inter-
ruption)Component that is to be master has been discon-
nected after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±

DI±1988
± DIAGNOSTICSAUDIO SYSTEM
2182 Author: Date:
2005 SEQUOIA (RM1146U)E0
*1
Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Request command is output from
sub±master component.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
D8
*2No Response To Connection
CheckComponent shown by sub±code is or had been
disconnected from system after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
D9
*1Last Mode Error
Component operated (sound and/or image was
provided) before engine stop is or was discon-
nected with ignition switch in ACC or ON.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DANo Response to ON/OFF
Instruction
No response is identified when changing mode
(audio and visual mode change).
Detected when sound and picture does not
change by button operation
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DB
*1Mode Status ErrorDual alarm is detected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DC
*4Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DE
*3Slave Reset (Momentary Inter-
ruption)After engine start, slave component has been dis-
connected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

± DIAGNOSTICSAUDIO SYSTEM
DI±1989
2183 Author: Date:
2005 SEQUOIA (RM1146U)

*2: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.

*3: This code may be stored when the engine key is turned 1 min. again after engine start.

*4: This code may be stored when the engine key is turned again after engine start.

I28499
Built±in Type Amplifier:
Radio Receiver Assy A36
ACC Cut Relay Sub J/B No. 3
Instrument Panel J/B
Engine Room J/BTo ECM
Battery
IFR2
R2
R2 12
3A1
3A
1
4 3 W±R
2
GR B C B±O
J37 J38
IA124
L±Y L±Y GR
2B
2C8
2D1 RAD No. 1
ECU±BShort Pin 3
W±R
BRB RAD No. 2
3
1 6AM1 212 1
P
31ALT
5
B
I18
Ignition SWW±L1 2
AACC+B
GND BU+B 4 3
7 W±R
1J
1E
1L 1C1C1F
ACCAM1
GR
8
F10
Fusible Link Block
4 WJ/C
J12
Junction
Connector DI±1990
± DIAGNOSTICSAUDIO SYSTEM
2184 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
Power source circuit (Radio receiver assy)
CIRCUIT DESCRIPTION
This circuit provides power to the radio receiver assy.
WIRING DIAGRAM
DID9U±01

I28498
11 Radio Receiver Assy
ACC+B
1
R420
GND GR 1
RAD No. 24 3 A36
ACC Cut Relay
P
31AM1 ACC12 Sub J/B No. 3
3AW±R
W±R1
IA124
L±Y L±Y
2B
3
2C8
2D1 Engine Room J/B
RAD No. 1
ECU±BShort Pin 1J3
1E
W±R
1L1
1C6AM12
ALT
5
B
Battery
IOBR Separate Type Amplifier:
R4 R4 3A
I18
Ignition SWW±LB 212 1
1C 1FGR
GRB C B±O
J37To ECM
J38
Instrument Panel J/B
1 2BU+B
W
8
4 F10
Fusible Link BlockJ/C
± DIAGNOSTICSAUDIO SYSTEM
DI±1991
2185 Author: Date:
2005 SEQUOIA (RM1146U)

I28500
GR 1
4 3 A36
ACC Cut Relay
12 Sub J/B No. 3
3AW±R 1
2 3A
GRB C B±O
J37To ECM
J38
RAD No. 2
3
1 6AM1 212 1Instrument Panel J/B
1 2
P
3
AM1
ACC W±R
W±LALT
5
B
Battery W±RILI2
L±W
2A
2C8
2D1 Engine Room J/B
RAD No. 3
ECU±BShort Pin 3
B B
BBJ11
J10 J11 L±W
IOBR
BRS10
S9
S9S9
S9 12
10
15
161ACC
B2+
B+
GND
E Stereo Component
Amplifier Assy
1J 1E
1L 1C 1C 1FJ/C
J/C
GR
8
4 F10
Fusible Link Block WL±W L±W
I18
Ignition SW
± DIAGNOSTICSAUDIO SYSTEM
DI±1993
2187 Author: Date:
2005 SEQUOIA (RM1146U)
Power source circuit (Stereo component amplifier assy)
CIRCUIT DESCRIPTION
This circuit provides power to the stereo component amplifier assy.
WIRING DIAGRAM
DID9V±01

± DIAGNOSTICSAUDIO SYSTEM
DI±2027
2221 Author: Date:
2005 SEQUOIA (RM1146U)
Noise occurs
INSPECTION PROCEDURE
1 Check of speaker installation.
CHECK:
Check if each speaker is securely installed.
OK:
Each speaker is securely installed.
HINT:
The radio is equipped with a noise prevention system that blocks excessively loud noise. If such noise oc-
curs, check the all wiring is proper and that the antenna installation part ground and noise±prevention equip-
ment are installed.
Condition in which noise occursNoise type
Noise increases when the accelerator pedal is depressed, but stops when
the engine is stopped.Generator noise
Noise occurs during A/C or the heater operation.Blower motor noise
Noise occurs when the vehicle accelerates rapidly on an unpaved road or
after the ignition switch is turned on.Fuel pump noise
Noise occurs when the horn switch is pressed and released or when pressed
and held.Horn noise
Quiet noise occurs while the engine is running, but stops when the engine is
stopped.Ignition noise
Noise occurs synchronously with the blink of the turn signal.Flasher noise
Noise occurs during window washer operation.Washer noise
Noise occurs while the engine is running, and it continues even after the en-
gine is stopped.Water temperature sensor noise
Noise occurs during wiper operation.Wiper noise
Noise occurs when the brake pedal is depressed.Stop light switch noise
Others.Static electricity stored on the vehicle
HINT:

Identify the condition under which the noise occurs, and check the noise filter on the related part.

First ensure that the noise is not coming from the outside. Failure to do so makes noise source detec-
tion difficult and may lead to a misdiagnosis.

Noise should be removed in descending order of loudness.
NG Install it properly.
OK
Identification of noise source (See page DI±1964).
DIDA3±01