2001 TOYOTA SEQUOIA engine

DIDBP±01
I27727
Instrument Panel J/B

RAD NO. 2 Fuse

ECU±B Fuse

AM1 FuseEngine Room J/B

RAD NO. 1 Fuse

RAD NO. 3 Fuse
Steering Pad
Switch
Ignition SwitchDisc Player
Controller
(*1)
Stereo
Component
Amplifier
Multi±display
Controller (*1)
VTR
Terminal
(*1)Headphone
Terminal
(*1) (*2)
Radio and
Navigation Assy GPS Antenna
TweeterTelevision Display Assy (*1)
Rear Seat Audio
Controller Assy (*2)
Rear Door SpeakerRear Door Speaker
Front Door Speaker
and Woofer
Front Door Speaker
and Woofer
*1: w/ RSE System
*2: w/ RSA System
DI±2160
± DIAGNOSTICSNAVIGATION SYSTEM
2354 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDBR±01
I28195
I28196
I28197
DI±2162
± DIAGNOSTICSNAVIGATION SYSTEM
2356 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. SYSTEM NORMAL CONDITION CHECK
(a) If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.
SymptomAnswer
A longer route than expected is chosen.Depending on the road conditions, the navigation ECU may determine that a longer
route is quicker.
Even when distance priority is high, the shortest route is not
shown.Some paths may not be advised due to safety concerns.
When the vehicle is put into motion immediately after the
engine starts, the navigation system deviates from the actu-
al position.If the vehicle starts before the navigation system activates, the system may not
react.
When running on certain types of roads, especially new
roads, the vehicle position deviates from the actual position.When the vehicle is driving on new roads not available on the map disc, the system
attempts to match it to another nearby road, causing the position mark to deviate.
(b) The following symptoms are not a malfunction, but are
caused by errors inherent in the GPS, gyro sensor, speed
sensor, and navigation ECU.
(1) The current position mark may be displayed on a
nearby parallel road.
(2) Immediately after a fork in the road, the current ve-
hicle position mark may be displayed on the wrong
road.
(3) When the vehicle turns right or left at an intersec-
tion, the current vehicle position mark may be dis-
played on a nearby parallel road.

DIDC5±01
I28205
I28206
Upper Left
Lower Left
I28207
± DIAGNOSTICSNAVIGATION SYSTEM
DI±2191
2385 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
HINT:

Illustrations may differ from the actual vehicle depending on the device settings and options. There-
fore, some detailed areas may not be shown exactly the same as on the actual vehicle.

After the ignition switch is turned on, check that the map is displayed before starting the diagnostic
mode. Otherwise, some items cannot be checked.
1. There are 2 methods to start diagnostic mode. Start the mode by using one of them.
2. Method 1
(a) Start the engine.
(b) While pressing and holding ºINFOº switch, operate the
light control switch, OFF " TAIL " OFF " TAIL " OFF
" TAIL " OFF.
(c) The diagnostic mode starts and the service check screen
(ºSystem Check Modeº) will be displayed. Service inspec-
tion starts automatically and the result will be displayed.
3. Method 2
(a) Start the engine.
(b) Switch to the ºDisplay quality adjustmentº screen.
(c) From the display quality adjustment screen, touch the
corners of the screen in the following order: upper left "
lower left "upper left " lower left " upper left " lower
left.
(d) The diagnostic mode starts and ºService Checkº screen
will be displayed. Service inspection starts automatically
and the result will be displayed.
4. Diagnosis MENU
(a) Diagnostic screen will be displayed by pressing the menu
switch on the service check screen.

DIDC7±01
± DIAGNOSTICSNAVIGATION SYSTEM
DI±2203
2397 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
TermsDescription
Physical address
3±digit, hexadecimal code assigned to all components connected to the AVC±LAN.
Individual symbols are specified based on function. Units whose names are un-
known or relevant units are displayed with physical addresses.
Logical address2±digit, hexadecimal code assigned to all the functions in the AVC±LAN system.
HINT:
Titles for each unit are stated in the following order: parts name (physical address) [Name indicated by DTC]
1. Radio and navigation assy (physical address: 140) [AVN]
(a) Logical address: 01 (Communication control)
HINT:
Methods used to verify the cause of the problem are listed in order of probability in the verification column.
DTCNameDiagnosisVerificationSee page
D5
*1
*5Absence of registration unit
A device that the sub code shows is (was) dis-
connected from the system when turning the igni-
tion switch to the ACC or ON position.
The communication condition with the device that
the code shows cannot be obtained when the en-
gine starts.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy). *7
4. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
5. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
6. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±2258
DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±
D8
*2
*5No response to connection
checkThe device indicated by the sub code is (was)
disconnected from the system after engine start.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy). *7
4. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
5. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
6. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±2258
DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±

DI±2204
± DIAGNOSTICSNAVIGATION SYSTEM
2398 Author: Date:
2005 SEQUOIA (RM1146U) D9
*1
*5
Last mode error
The device (for audio visual system) that had
functioned before the engine stopped is (was)
disconnected from the system when the ignition
switch is (was) in the ACC or ON position.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy). *7
4. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
5. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
6. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±2258
DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±

DI±2206
± DIAGNOSTICSNAVIGATION SYSTEM
2400 Author: Date:
2005 SEQUOIA (RM1146U) DC
*3
*5
Failure in transmission
This code indicates a transmission failure to the
device indicated by the sub code.
NOTE: This DTC may have no direct relationship
with the malfunction.
1. Power source circuit (Rear seat
audio controller). *6
2. Power source circuit (Multi±dis-
play controller sub±assy). *7
3. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
4. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
5. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
6. Replace stereo component am-
plifier assy.
7. Replace rear seat audio control-
ler. *6
8. Replace multi±display controller
sub±assy. *7DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±
DE
*4
*5
Slave resetThis code is stored when a slave device has been
disconnected after engine start.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy). *7
4. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
5. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
6. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±2258
DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±
21ROM errorThis code is output when a malfunction exists in
ROM.Replace radio and navigation assy.±
22RAM errorThis code is output when a malfunction exists in
RAM.Replace radio and navigation assy.±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: If the power connector is disconnected after the engine starts, this code is recorded after 180 se-
conds.

*3: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*4: This code may be stored if the ignition key is held in the START position for 1 minute or more before
returning to the ON position.

*5: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*6: w/ Rear seat audio system only.

± DIAGNOSTICSNAVIGATION SYSTEM
DI±2207
2401 Author: Date:
2005 SEQUOIA (RM1146U)

*7: w/ Rear seat entertainment system only.
(b) Logical address: 58 (Navigation): 80 (GPS)
HINT:
Methods used to verify the cause of the problem are listed in order of probability in the verification column.
DTCNameDiagnosisVerificationSee page
43SPD signal errorThe difference between the GPS speed and SPD
pulse is detected.
1. Inspect speed signal error.
2. Speed signal circuit.
3. Replace radio and navigation
assy.±
DI±2291
±
44Player errorMap player error is detected.
1. Check if the disc can be inserted
and ejected. If a malfunction is
found, replace the radio and nav-
igation assy.
2. If the same code is detected
again, replace the radio and nav-
igation assy.±
±
45High temperatureHigh map player temperature is detected.
1. Park the vehicle in a cool place.
Turn the engine off. After check-
ing that the temperature of the
radio and navigation assy be-
comes sufficiently low, turn the
engine on to verify the malfunc-
tion symptom.
2. If the same code is detected
again, replace the radio and nav-
igation assy.±
±
(c) Logical address: 21 (SW): 23 (SW with name): 24 (SW converting): 25 (command SW)
HINT:
Methods used to verify the cause of the problem are listed in order of probability in the verification column.
DTCNameDiagnosisVerificationSee page
10Panel switch errorThe panel SW detection circuit has a failure.Replace radio and navigation assy.±

DI±2208
± DIAGNOSTICSNAVIGATION SYSTEM
2402 Author: Date:
2005 SEQUOIA (RM1146U)
2. Stereo component amplifier assy (Physical address: 440) [DSP AMP]
(a) Logical address: 01 (Communication control)
HINT:
Methods used to verify the cause of the problem are listed in order of probability in the verification column.
DTCNameDiagnosisVerificationSee page
D7
*2Connection check error
When either of the following conditions is met.

The device that stored this code has (had) been
disconnected after the engine starts (started).

The master device has (had) been disconnected
when this code is (was) stored.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
3. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *5
4. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *6
5. Power source circuit (stereo
component amplifier assy).
6. Replace radio and navigation
assy.
7. Replace stereo component am-
plifier assy.DI±2256
DI±2268
DI±2061
DI±2139
DI±2258
±
±
DC
*3
*4
Transmission error
The device stores the fact that transmission to the
device indicated by the sub code has failed.
NOTE: This DTC may not be directly related to
the problem.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
3. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *5
4. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *6
5. Power source circuit (stereo
component amplifier assy).
6. Replace radio and navigation
assy.
7. Replace stereo component am-
plifier assy.DI±2256
DI±2268
DI±2061
DI±2139
DI±2258
±
±
E0
*1Registration complete indication
error
When ºRegistration completeº command from the
master device cannot be received.
NOTE: This DTC may not be directly related to
the problem.
±±
E1
*1Voice processing device ON er-
rorWhen the AMP device records that the AMP out-
put does not function even while the source de-
vice operates.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
3. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *5
4. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *6
5. Replace radio and navigation
assy.DI±2256
DI±2268
DI±2061
DI±2139
±