2001 TOYOTA SEQUOIA differential

SA24B±02
F14284
Socket Wrench
F14286
F14287
SST
SST
F14288
SST
SST
± SUSPENSION AND AXLEREAR AXLE SHAFT
SA±101
3097 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
1. INSTALL BEARING ASSEMBLY
Position the backing plate on the bearing assembly and using
a press and 2 socket wrenches, install the serration bolts.
2. INSTALL OIL DEFLECTOR AND GASKET
Position a new gasket and oil deflector on the axle shaft and
install a washer and nut to a new hub bolt, as shown in the il-
lustration, and install the hub bolt by torquing the nut.
3. INSTALL REAR AXLE SHAFT TO BACKING PLATE
(a) Install the backing plate, spring washer and bearing re-
tainer on the rear axle shaft.
(b) Using SST and a press, install the rear axle shaft into the
backing plate.
SST 09631±12090, 09950±60020 (09951±01030)
4. INSTALL SNAP RING TO AXLE SHAFT
Using a snap ring expander, install a new snap ring.
5. INSTALL SPEED SENSOR ROTOR AND BEARING RE-
TAINER (DIFFERENTIAL SIDE)
Using SST and a press, install a new speed sensor rotor and
bearing retainer.
SST 09631±12090, 09950±60020 (09951±01030)
Standard length: 132.8 ± 1.0 mm (5.228 ± 0.039 in.)

SA15K±09
F14321

Oil Seal
Front Bearing

Bearing Spacer
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable partCompanion Flange
Rear Propeller ShaftWasher


74 (750, 54)
Drive Pinion
2WD:
10 (102, 7.4)
74 (750, 54)

See page SA±119
Stud BoltCompanion
Flange
See page SA±119
SA±104
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
3100 Author: Date:
2005 SEQUOIA (RM1146U)
REAR DIFFERENTIAL FRONT OIL SEAL
COMPONENTS

SA24D±04
F14486
40 mm
(1.57 in.)
F14485
SST
F14484
SST
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
SA±105
3101 Author: Date:
2005 SEQUOIA (RM1146U)
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
2. DISCONNECT REAR PROPELLER SHAFT
2WD: See page PR±3
4WD: See page PR±7
3. REMOVE COMPANION FLANGE
(a) 2WD:
Remove the companion flange nut.
(1) Using a chisel and hammer, loosen the staked part
of the nut.
(2) Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(3) Set the SST and install the 3 nuts to the companion
flange.
SST 09213±58013
(4) Install the other SST to the set SST to hold the com-
panion flange, and remove the nut.
SST 09330±00021
(5) Remove the 3 nuts, SST and stud bolts from the
companion flange.

SA2349
SST
R13357
SST
R13358
SST SST
R13359
SST SA±106
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
3102 Author: Date:
2005 SEQUOIA (RM1146U)
(b) 4WD:
(1) Using a chisel and hammer, loosen the staked part
of the nut.
(2) Using SST to hold the flange, remove the nut.
SST 09330±00021
(c) Using SST, remove the companion flange.
SST 09950±30012 (09951±03010, 09953±03010,
09954±03010, 09955±03030, 09956±03050)
4. REMOVE OIL SEAL
Using SST, remove the oil seal.
SST 09308±10010
5. REMOVE FRONT BEARING
Using SST, remove the front bearing from the drive pinion.
SST 09556±22010
6. REMOVE BEARING SPACER
(a) Remove the 2 washers.
(b) Remove the bearing spacer.
7. INSTALL NEW BEARING SPACER
(a) Install a new bearing spacer.
(b) Install the 2 washers.
8. INSTALL FRONT BEARING
(a) Place the front bearing.

R13361
SST
R13360
SST
Vinyl Tape
F14486
40 mm
(1.57 in.)
F14485
SST
F14522SST
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
SA±107
3103 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Using SST and the companion flange, install the front
bearing then remove the companion flange.
SST 09950±30012 (09951±03010, 09953±03010,
09954±03010, 09955±03030, 09956±03050)
9. INSTALL NEW OIL SEAL
(a) Coat a new oil seal lip with MP grease.
(b) Using SST and a plastic hammer, install the oil seal until
its surface is flush with the differential carrier end.
SST 09316±12010, 09649±17010
HINT:
Connect 2 SST with vinyl tape.
10. INSTALL COMPANION FLANGE
(a) Place the companion flange on the drive pinion.
(b) Coat the threads of a new nut with hypoid gear oil.
(c) 2WD:
Install the companion flange nut.
(1) Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(2) Set the SST and install the 3 nuts to the companion
flange .
SST 09213±58013
(3) Install the other SST to the set SST to hold the com-
panion flange and torque the nut.
SST 09330±00021
Torque: 147 N´m (1,500 kgf´cm, 109 ft´lbf)
(4) Remove the 3 nuts, SST and stud bolts from the
companion flange.

FA1083
SST
FA1084
R13337
Less than
5 mm (0.20 in.) SA±108
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
3104 Author: Date:
2005 SEQUOIA (RM1146U)
(d) 4WD:
Using SST to hold the flange, torque the nut.
SST 09330±00021
Torque: 147 N´m (1,500 kgf´cm, 109 ft´lbf)
11. ADJUST DRIVE PINION PRELOAD
(See page SA±119)
12. STAKE DRIVE PINION NUT
13. CONNECT REAR PROPELLER SHAFT
2WD: See page PR±5
4WD: See page PR±9
14. FILL DIFFERENTIAL WITH HYPOID GEAR OIL
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
Oil type: Hypoid gear oil API GL±5
Recommended oil viscosity:
SAE 75W ± 140 (Synthetic)
Capacity: 3.65 liters (3.86 US qts, 3.21 Imp. qts)

SA15M±05
F14291
Brake Caliper
Disc Parking Brake Assembly Drain Plug
Gasket Filler Plug
Parking Brake
Cable Differential Carrier Axle Shaft (RH)
x10 Propeller ShaftAxle Shaft (LH)
Gasket 

49 (500, 36)
Clip
O±ring

122 (1,244, 90)
Gasket 
49 (500, 36)
15.5 (158, 11)
N´m (kgf´cm, ft´lbf) : Specified torque
Non±reusable part
74 (750, 55)
73 (744, 53)
105 (1,070, 77)
8.0 (82, 71 in.´lbf)10 (102, 7.4)
2WD:
74 (750, 55)
Stud Bolt
± SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
SA±109
3105 Author: Date:
2005 SEQUOIA (RM1146U)
REAR DIFFERENTIAL CARRIER
COMPONENTS

F14292
N´m (kgf´cm, ft´lbf) : Specified torqueStraight Pin
Pinion ShaftPinion Gear
Thrust Washer
Side Gear
Ring Gear

Differential Case
Drive Pinion
Rear Bearing
 Adjusting Washer
 Bearing Spacer
Front Bearing
 Dust Deflector Companion Flange
Bearing CapThrust Washer
Plate Washer
Side Bearing
Side Bearing
Plate Washer
Differential Carrier
Washer
Oil Seal
x12
125 (1,270, 92)
113 (1,150, 83)
113 (1,150, 83)
See page SA±119
 Non±reusable part

Precoated part
Companion
Flange
2WD: SA±110
± SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
3106 Author: Date:
2005 SEQUOIA (RM1146U)