Page 122 of 1897
D07989
AX0KD-01
D07988
2
4
3
1
2
D07990
D07221
D07991
AX-24
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
1314 Author: Date:
2001 AVALON (RM808U)
DISASSEMBLY
1. REMOVE O/D MAIN SWITCH TERMINAL
(a) Remove the connector from the shift lever plate.
(b) Remove the secondary locking device.
(c) Release the looking lug of the terminals 2 and 4, and pull
the terminals out from the rear.
(d) Separate the O/D main switch wire harness from the 2
clamps.
2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Side the shift lever knob cover.
(b) Remove the 2 screws and shift lever knob sub-assembly.
NOTICE:
Pay attention not to apply unnatural load onto O/D main
switch wire harness.
3. DISASSEMBLE SHIFT LEVER KNOB
SUB-ASSEMBL Y
(a) Using a small screwdriver, remove the O/D main switch
cover.
(b) Using a small screwdriver, remove the O/D main switch
from the shift lever knob.
Page 123 of 1897
D07992
D07220
D07222
D07239
D07225
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
AX-25
1315 Author: Date:
2001 AVALON (RM808U)
(c) Insert a small screwdriver into the position in the illustra-
tion and disengage the claw.
(d) Remove the shift lever knob button and compression
spring.
4. REMOVE INDICATOR LIGHT
(a) Remove the indicator light from the lower position indica-
tor housing.
(b) Remove the cap and bulb from the indicator light wire.
5. REMOVE LOWER POSITION INDICATOR HOUSING
Remove the 4 screws and lower position indicator housing.
6. DISASSEMBLE LOWER POSITION INDICATOR
HOUSING
(a) Remove the control position indicator plate.
(b) Remove the shift lock release button and spring.
(c) Remove the slide cover.
7. REMOVE SHIFT LOCK CONTROL UNIT
Remove the 2 screws and shift lock control unit assembly.
Page 128 of 1897
D07999
A00452F01188
A Shift Lever
Sub-assembly
Detent Rod
Grooved Pin
D07223
D07224
D07225
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
AX-29
1319 Author: Date:
2001 AVALON (RM808U)
(d) Meet the grooved pin with the notch of the guide hole.
(e) Press the pin with a hammer.
A: 10.0 - 10.4 mm (0.39 - 0.41 in.)
NOTICE:
When pressing in the grooved pin, if doing it at the place
other than the notch, the shift lever sub-assembly might be
damaged.
5. CHECK DETENT ROD OPERATION
6. INSTALL SHIFT LEVER KNOB SLEEVE
7. INSTALL MANUAL DETENT SPRING
Install the manual detent spring with the screw.
8. INSTALL SHIFT LOCK CONTROL UNIT
Install the shift lock unit assembly with the 2 screws.
Page 129 of 1897
D08000
D07239
D07222
D07220
AX-30
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
1320 Author: Date:
2001 AVALON (RM808U)
NOTICE:
Install the grooved pin into the groove of the shift lock unit
as shown in the illustration.
9. ASSEMBLE LOWER POSITION INDICATOR HOUSING
(a) Install the slide cover.
(b) Install the spring and shift lock release bottom.
(c) Install the control position indicator plate.
10. INSTALL LOWER POSITION INDICATOR HOUSING
Install the lower position indicator housing with the 4 screws.
11. INSTALL INDICATOR LIGHT
(a) Install the bulb and cap to the indicator light wire.
(b) Install the indicator light to the lower position indicator
housing.
12. ASSEMBLE SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Install the spring and shift lever knob to the shift lever
knob.
(b) Install the O/D main switch and O/D main switch cover to
the shift lever knob.
13. INSTALL SHIFT LEVER KNOB AND SHIFT LEVER
KNOB COVER
(a) Pass through the wire harness of the O/D main switch as
shown in the illustration and set it.
(b) Install the shift lever knob and shift lever knob cover to the
shift lever sub-assembly.
NOTICE:
When operating the shift lever sub-assembly, check that
excessive force is not applied to the wire harness of the
O/D main switch.
Page 133 of 1897
Q00229
AX0CJ-02
Q06496
Q05727
Q04617
Q04687
AX-4
- AUTOMATIC TRANSAXLEPARK/NEUTRAL POSITION (PNP) SWITCH
1294 Author: Date:
2001 AVALON (RM808U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON-VEHICLE REPAIR
1. REMOVE ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the clip from the shift control cable.
(b) Remove the nut and disconnect the control cable.
(c) Remove the nut, washer and transaxle control shaft lever.
(d) Using a screwdriver, pry off the lock plate.
(e) Remove the nut and lock plate.
(f) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL AND ADJUST PARK/NEUTRAL POSITION
SWITCH
(a) Install the park/neutral position switch with the 2 bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Install a new lock plate and nut.
Torque: 6.9 N´m (70 kgf´cm, 61 in.´lbf)
(c) Bend the claws on the lock plate to stake the nut.
(d) Install the transaxle control shaft lever and washer.
(e) Install and torque the nut.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
Page 135 of 1897
AX05E-03
D02451D02452D02453D02455
ABC
IGP
P2 P1 ACC
STP KLS
+ESLS
-SLS+
Q06585
Q06584
AX-18
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
1308 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the shift lock control unit assembly connec-
tor.
Terminal No. (Symbols)Measuring ConditionVoltage (V)
1 (ACC) - 5 (E)Ignition switch ACC10 - 14
3 (IG) - 5 (E)Ignition switch ON10 - 14
6 (STP) - 5 (E)Depressing brake pedal10 - 14
4 (KLS+) - 5 (E)
4. Ignition switch ACC and P position
5. Ignition switch ACC and except P position
6. Ignition switch ACC and except P position (After approx. 1 second)0
7.5 - 11
6 - 9
1. Ignition switch ACC and P position0
2 (SLS+) - 1 (SLS-)
1.Ignition switch ACC and P osition
2. Depress brake pedal
0
8.5 -13.52 (SLS) 1 (SLS)2.De ress brake edal
3. Except P position
8.5 13.5
0
4 (P1) 1 (P)1. Ignition switch ON, P position and depress brake pedal04 (P1) - 1 (P)1.Ignition switch ON, P osition and de ress brake edal
2. Shift except P position under condition above
0
9 - 13.5
3 (P2) 1 (P)1. Ignition switch ACC and P position9 - 13.53 (P2) - 1 (P)1.Ignition switch ACC and P osition
2. Shift except P position under condition above
9 13.5
0
2. INSPECT SHIFT LOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure resistance between termi-
nals.
Standard resistance: 29 - 35 W
If resistance value is not as specified, replace the solenoid.
(c) Supply battery positive voltage between terminals. Check
that an operation noise can be heard from the solenoid.
If the solenoid does not operate, replace the solenoid.
Page 136 of 1897
AT8748
D02459
21
D07236
P
P2
P1
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
AX-19
1309 Author: Date:
2001 AVALON (RM808U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Standard resistance: 12.5 -16.5 W
If resistance value is not as specified, replace the solenoid.
(c) Supply battery positive voltage between terminals.
If the solenoid does not operate, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that continuity between at each terminal.
Shift positionTester connectionSpecified value
P position (Release button
is not pushed)3 (P1) - 1 (P)Continuity
P position (Release button
is pushed)3 (P1) - 1 (P)
4 (P2) - 1 (P)Continuity
R, N, D, 2, L position4 (P2) - 1 (P)Continuity
If continuity is not specified, replace the switch.
Page 137 of 1897
AX03T-04
D07231
Shift Lock Control Switch
Key Interlock Solenoid
Stop Light Switch Shift Lock Solenoid
Shift Lock Control ECU
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
AX-17
1307 Author: Date:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Column Shift)
LOCATION
