Page 633 of 1897
DI6N7-01
F07879
F02201
E1Tc
DLC1
F00103
Normal Code
0.25 sec.
0.25 sec. 0.5 sec.
ON
OFF
ON
OFF0.5 sec. 0.5 sec.
Code 11 and 21
4 sec.1.5 sec.
2.5 sec.
Code 11 Code 21
DI-212- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM WITH ELECTRONIC
BRAKE FORCE DISTRIBUTION (EBD)
368 Author: Date:
2001 AVALON (RM808U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Release the parking brake pedal.
(b) Check the indicator.
When the ignition switch is turned ON, check that the ABS
warning light and BRAKE warning light goes on for
approx. 3 seconds.
HINT:
When the parking brake is applied or the level of the brake
fluid is low, the BRAKE warning light is lit.
If the indicator check result is not normal, proceed to trou-
bleshooting for the ABS warning light circuit or BRAKE
warning light circuit (See page DI-243, DI-240).
(c) Check the DTC.
(1) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(2) Turn the ignition switch ON and read the DTC from
the ABS warning light on the combination meter.
HINT:
If no codes appears, inspect the diagnostic circuit or ABS
warning light circuit (See page DI-245 or DI-243).
As an example, the blinking patterns for normal code and
codes 11 and 21 are shown on the left.
(3) Codes are explained in the code table on page
DI-215.
(4) After completing the check, disconnect terminals Tc
and E
1, and turn off the display.
If 2 or more malfunction codes are identified at the
same time, the lowest numbered DTC will be dis-
played 1st.
Page 634 of 1897
BR3890
F02201
DLC1
Ts E
1
Tc
BR3904
0.13 sec. 0.12 sec.
ON
OFF
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM WITH ELECTRONIC
BRAKE FORCE DISTRIBUTION (EBD)DI-213
369 Author: Date:
2001 AVALON (RM808U)
(d) Clear the DTC.
(1) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(2) Turn the ignition switch ON.
(3) Clear the DTC stored in ECU by depressing the
brake pedal 8 times or more within 5 seconds.
(4) Check that the warning light shows the normal
code.
(5) Remove the SST from the terminals of DLC1.
SST 09843-18020
HINT:
Cancellation cannot be done by removing the battery cable or
ECU-IG fuse.
2. SPEED SENSOR SIGNAL CHECK (TEST MODE)
(a) Check the sensor signal.
(1) Using SST, connect terminals Ts and E
1 of DLC1.
SST 09843-18020
(2) Start the engine.
(3) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI-243).
(4) Drive vehicle straight forward.
(5) Drive vehicle at a speed faster than 45 km/h (28
mph) for several seconds.
HINT:
If the brake is applied during the check, the check routine must
be started again.
(6) Stop the vehicle.
(7) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(8) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC shown on the next page.
If every sensor is normal, a normal code is output (A cycle
of 0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction codes are identified at the same
time, the lowest numbered code will be displayed 1st.
Page 638 of 1897
F09823
ABS & BA &
TRAC & VSC ECU
WA A2081
47 1
B
W-B
B
BJ4
J/C
W-B W-B
IG Battery FL MAINA21
Active
Light
Relay
F10F8 F61 1
1ALT
W W
W-B
B-L
2G
2H 11
5512 AM1
B
W-LIF17 W-L 22
Y-R
IG1 AM1 4
Ignition Switch W-R 1B 1C1G1B1D
4
3 4 3 1
1
213 10 GAUGE No. 1
ECU-IG
No. 2
Y-R3C
3D 2
11 R-B
R-B 4D
4FM6M6
4
Multi
Display 13 45 R-LR-L
4A4B
4H15
15 15
R-L 14
E1
ABS D2
DLC2
ABS
J/B No. 4
J/B No. 3 Driver Side J/B
Engine Room J/B
Engine Room R/B No. 5J/B No. 4
FL Block IG1
Relay
B
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI-325
481 Author: Date:
2001 AVALON (RM808U)
ABS Warning Light Circuit
WIRING DIAGRAM
DI6OI-03
Page 639 of 1897
DI-326
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
482 Author: Date:
2001 AVALON (RM808U)
INSPECTION PROCEDURE
HINT:
Troubleshoot in accordance with the chart below for each trouble symptom.
ABS warning light does not light up*
ABS warning light remains onGo to step 2
*: Start the inspection from step 1 in case of using a TOYOTA hand-held tester and start from step 2 in case
of not using the TOYOTA hand-held tester.
1 Check operation of the ABS warning light.
PREPARATION:
(a) Connect the TOYOTA hand-held tester to the DLC3.
(b) Turn the ignition switch ON and push the TOYOTA hand-held tester main switch ON.
(c) Select the ACTIVE TEST mode on the TOYOTA hand-held tester.
CHECK:
Check that ºONº and ºOFFº of the ABS warning light can be shown on the combination meter on the TOYOTA
hand-held tester.
OK Check and replace ABS & BA & TRAC & VSC
ECU.
NG
2 Check ABS warning light.
See combination meter troubleshooting on page BE-2.
NG Replace bulb or repair combination meter as-
sembly.
OK
3 Check active lamp relay.
NG Replace active lamp relay.
OK
Repair or replace and check for open or short circuit in harness and connector.
Page 640 of 1897
F09818
ABS & BA &
TRAC & VSC ECU
VSCW A2070
P-B
R-B 15
4D
4F 134 4F15
4C P-BJ/B No. 4
M6 M6
R-B4
10 Multi Display
Driver Side J/B
1G1
1D 10
1B3
1C4
3
4 12 IG1 RelayGAUGE
No. 1
W-R 2
IG1 AM1
4 Ignition Switch
W-L W
IF1
7
W-L
5
5 1 2AM1 Engine Room R/B No. 5
B2G 2H11W-B
IG B-L
Battery
FL MAIN
B
F61 F10 F81 1
ALT
FL BlockVSC
Engine Room J/B DI-322
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
478 Author: Date:
2001 AVALON (RM808U)
DTC Always ON Malfunction in ECU
VSC Warning Light Circuit
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
Always ON
Either of the following 1. or 2. is detected:
1. There is a malfunction in the ECU internal circuit.
2. There is a malfunction in VSC warning light circuit.Charging system
VSC warning light circuit
HINT:
TOYOTA hand-held tester may not be able to be used when ECU is defective.
WIRING DIAGRAM
DI6OH-03
Page 642 of 1897
DI-324
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
480 Author: Date:
2001 AVALON (RM808U)
5 Check operation of the VSC warning light.
In case of using the TOYOTA hand-held tester:
PREPARATION:
(a) Connect the TOYOTA hand-held tester to the DLC3.
(b) Turn the ignition switch ON and push the TOYOTA hand-held tester main switch ON.
(c) Select the ACTIVE TEST mode on the TOYOTA hand-held tester.
CHECK:
Check that ºONº and ºOFFº of the VSC warning light can be shown on the combination meter by the TOYOTA
hand-held tester.
In case of not using the TOYOTA hand-held tester:
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the connector from the ABS & BA & TRAC & VSC ECU.
(c) Turn the ignition switch ON.
CHECK:
Check the VSC warning light goes off.
NG Check and replace combination meter (See
page BE-2).
OK
6 Check for short circuit in harness and connector between combination meter
and ABS & BA & TRAC & VSC ECU, combination meter and DLC1 (See page
IN-30).
NG Repair or replace harness or connector.
OK
Check and replace ABS & BA & TRAC & VSC
ECU.
Page 643 of 1897
F09823
ABS & BA &
TRAC & VSC ECU
WA A2081
47 1
B
W-B
B
BJ4
J/C
W-B W-B
IG Battery FL MAINA21
Active
Light
Relay
F10F8 F61 1
1ALT
W W
W-B
B-L
2G
2H 11
5512 AM1
B
W-LIF17 W-L 22
Y-R
IG1 AM1 4
Ignition Switch W-R 1B 1C1G1B1D
4
3 4 3 1
1
213 10 GAUGE No. 1
ECU-IG
No. 2
Y-R3C
3D 2
11 R-B
R-B 4D
4FM6M6
4
Multi
Display 13 45 R-LR-L
4A4B
4H15
15 15
R-L 14
E1
ABS D2
DLC2
ABS
J/B No. 4
J/B No. 3 Driver Side J/B
Engine Room J/B
Engine Room R/B No. 5J/B No. 4
FL Block IG1
Relay
B
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI-319
475 Author: Date:
2001 AVALON (RM808U)
DTC Always ON Malfunction in ECU
ABS Warning Light Circuit
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
Always ON
Either of the following 1., 2. or 3. is detected:
1. The ECU connectors are OFF the ECU.
2. There is a malfunction in the ECU internal circuit.
3. There is a malfunction in ABS warning light circuit.
Charging system
ABS warning light circuit
HINT:
TOYOTA hand-held tester may not be able to be used when the ECU is defective.
WIRING DIAGRAM
DI6OG-02
Page 645 of 1897
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI-321
477 Author: Date:
2001 AVALON (RM808U)
5 Check operation of the ABS warning light.
In case of using the TOYOTA hand-held tester:
PREPARATION:
(a) Connect the TOYOTA hand-held tester to the DLC3.
(b) Turn the ignition switch ON and push the TOYOTA hand-held tester main switch ON.
(c) Select the ACTIVE TEST mode on the TOYOTA hand-held tester.
CHECK:
Check that ºONº and ºOFFº of the ABS warning light can be shown on the combination meter by the TOYOTA
hand-held tester.
In case of not using the TOYOTA hand-held tester:
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the connector from the ABS & BA & TRAC & VSC ECU.
(c) Turn the ignition switch ON.
CHECK:
Check the ABS warning light goes on.
OK Check and replace combination meter (See
page BE-2).
NG
6 Check for short circuit in harness and connector between active lamp relay and
ABS & BA & TRAC & VSC ECU (See page IN-30).
NG Repeir or replace harness or connector.
OK
Check and replace ABS & BA & TRAC & VSC
ECU.
