2001 NISSAN ALMERA wiring

Wiring Diagram Ð F/FOG Ð/SedanNJEL0361
HEL030B
FRONT FOG LAMP
Wiring Diagram Ð F/FOG Ð/Sedan
EL-89

Wiring Diagram Ð F/FOG Ð/HatchbackNJEL0428
YEL346C
FRONT FOG LAMP
Wiring Diagram Ð F/FOG Ð/Hatchback
EL-90

Wiring Diagram Ð R/FOG Ð/SedanNJEL0362WITHOUT FRONT FOG LAMPNJEL0362S01
HEL372B
REAR FOG LAMP
Wiring Diagram Ð R/FOG Ð/Sedan
EL-93

WITH FRONT FOG LAMPNJEL0362S02
HEL373B
REAR FOG LAMP
Wiring Diagram Ð R/FOG Ð/Sedan (Cont'd)
EL-94

Wiring Diagram Ð R/FOG Ð/HatchbackNJEL0429
YEL347C
REAR FOG LAMP
Wiring Diagram Ð R/FOG Ð/Hatchback
EL-95

Wiring Diagram Ð TURN Ð/SedanNJEL0364
HEL374B
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram Ð TURN Ð/Sedan
EL-99

HEL375B
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram Ð TURN Ð/Sedan (Cont'd)
EL-100

Trouble Diagnoses/SedanNJEL0033
Symptom Possible cause Repair order
Turn signal and hazard warning
lamps do not operate.1. Hazard switch
2. Combination flasher unit
3. Open in combination flasher unit
circuit
4. Combination flasher unit ground
circuit1. Check hazard switch.
2. Refer to combination flasher unit check.
3. Check wiring to combination flasher unit for open
circuit.
4. Check combination flasher unit ground circuit.
Turn signal lamps do not operate
but hazard warning lamps operate.1. 10A fuse
2. Hazard switch
3. Turn signal lamp switch
4. Open in turn signal lamp switch
circuit1. Check 10A fuse [No. 26, located in fuse block (J/B)].
Turn ignition switch ON and verify battery positive
voltage is present at terminal 2 of hazard switch.
2. Check hazard switch.
3. Check turn signal lamp switch.
4. Check the wire between combination flasher unit
terminal 3 and turn signal lamp switch terminal 1 for
open circuit.
Hazard warning lamps do not oper-
ate but turn signal lamps operate.1. 15A fuse
2. Hazard switch
3. Open in hazard switch circuit1. Check 15A fuse [No. 5, located in fuse block (J/B)].
Verify battery positive voltage is present at terminal
3 of hazard switch.
2. Check hazard switch.
3. Check the wire between combination flasher unit
terminal 3 and hazard switch terminal 4 for open
circuit.
Front turn signal lamp LH or RH
does not operate.1. Bulb
2. Grounds E30 and E73
3. Open in front turn signal lamp
circuit1. Check bulb.
2. Check grounds E30 and E73.
3. Check the wire between front turn signal lamp and
turn signal lamp switch.
Rear turn signal lamp LH or RH
does not operate.1. Bulb
2. Grounds B9, B21 and B308
3. Open in rear turn signal lamp
circuit1. Check bulb.
2. Check grounds B9, B21 and B308.
3. Check the wire between rear turn signal lamp and
turn signal lamp switch.
LH and RH turn indicators do not
operate.1. Ground 1. Check grounds M28 and M67.
LH or RH turn indicator does not
operate.1. Bulb
2. Open combination meter circuit1. Check bulb in combination meter.
2. Check the wire between hazard switch and combi-
nation meter.
SEL122E
Electrical Components InspectionNJEL0034COMBINATION FLASHER UNIT CHECKNJEL0034S01+Before checking, ensure that bulbs meet specifications.
+Connect a battery and test lamp to the combination flasher
unit, as shown. Combination flasher unit is properly function-
ing if it blinks when power is supplied to the circuit.
TURN SIGNAL AND HAZARD WARNING LAMPS
Trouble Diagnoses/Sedan
EL-101