2001 DODGE RAM tire pressure

DIAGNOSIS AND TESTING - FIXED ORIFICE
TUBE
The fixed orifice tube can be checked for proper
operation using the following procedure. However,
the fixed orifice tube is only serviced as a part of the
liquid line unit. If the results of this test indicate
that the fixed orifice tube is obstructed or missing,
the entire liquid line unit must be replaced.
WARNING: THE LIQUID LINE BETWEEN THE CON-
DENSER OUTLET AND THE FIXED ORIFICE TUBE
CAN BECOME HOT ENOUGH TO BURN THE SKIN.
USE EXTREME CAUTION WHEN PERFORMING THE
FOLLOWING TEST.
(1) Confirm that the refrigerant system is properly
charged. (Refer to 24 - HEATING & AIR CONDI-
TIONING - DIAGNOSIS AND TESTING - A/C PER-
FORMANCE)
(2) Start the engine. Turn on the air conditioning
system and confirm that the compressor clutch is
engaged.
(3) Allow the air conditioning system to operate for
five minutes.
(4) Lightly and cautiously touch the liquid line
near the condenser outlet at the front of the engine
compartment. The liquid line should be hot to the
touch.
(5) Touch the liquid line near the evaporator inlet
at the rear of the engine compartment. The liquid
line should be cold to the touch.
(6) If there is a distinct temperature differential
between the two ends of the liquid line, the orifice
tube is in good condition. If there is little or no
detectable temperature differential between the two
ends of the liquid line, the orifice tube is obstructed
or missing and the liquid line must be replaced.
REMOVAL
The fixed orifice tube is located in the liquid line,
between the condenser and the evaporator coil. If the
fixed orifice tube is faulty or plugged, the liquid line
assembly must be replaced. (Refer to 24 - HEATING
& AIR CONDITIONING/PLUMBING/LIQUID LINE
- REMOVAL)
ACCUMULATOR
DESCRIPTION
The accumulator is mounted in the engine com-
partment between the a/c evaporator outlet tube and
the compressor inlet.
OPERATION
Refrigerant enters the accumulator canister as a
low pressure vapor through the inlet tube. Any liq-
uid, oil-laden refrigerant falls to the bottom of the
canister, which acts as a separator. A desiccant bag is
mounted inside the accumulator canister to absorb
any moisture which may have entered and become
trapped within the refrigerant system (Fig. 13).
REMOVAL
WARNING: REVIEW THE WARNINGS AND CAU-
TIONS IN THE FRONT OF THIS SECTION BEFORE
PERFORMING THE FOLLOWING OPERATION.
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - WARNING) (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - CAUTION)
(1) Disconnect and isolate the battery negative
cable.
(2) Recover the refrigerant from the refrigerant
system. (Refer to 24 - HEATING & AIR CONDI-
TIONING/PLUMBING - STANDARD PROCEDURE -
REFRIGERANT RECOVERY)
(3) Remove the a/c low pressure switch from the
accumulator. (Refer to 24 - HEATING & AIR CON-
DITIONING/CONTROLS/A/C LOW PRESSURE
SWITCH - REMOVAL)
(4) Loosen the screw that secures the accumulator
retaining band to the support bracket on the dash
panel (Fig. 20).
(5) Disconnect the suction line refrigerant line fit-
ting from the accumulator outlet. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - A/C LINE COUPLERS)
Install plugs in, or tape over all of the opened refrig-
erant line fittings.
(6) Disconnect the accumulator inlet refrigerant
line fitting from the evaporator outlet. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
Fig. 12 FIXED ORIFICE TUBE - TYPICAL
1 - DIFFUSER SCREEN
2 - ªOº RINGS
3 - INLET FILTER SCREEN
4 - ORIFICE
24 - 54 PLUMBINGBR/BE
A/C ORIFICE TUBE (Continued)

UNDER VEHICLE
INSPECTION - TIRE PRESSURES
(1) Using the tire placard or the Safety Certifica-
tion Label, check that the correct tires are mounted
on the vehicle.
(2) Install valve stem extensions as required.
(3) Using the tire placard or the Safety Certifica-
tion Label, check tire pressure (including spare) and
adjust as required to recommended pressure.
(4) Inspect the spare tire for correct pressure and
proper mounting (Fig. 13).
NOTE: Tire pressure may have been set above nor-
mal during manufacturing in order to properly seat
the tire bead. Be sure to adjust to proper specifica-
tion.
INSPECTION - VISUAL
CAUTION: Before raising the vehicle on a hoist,
(Refer to LUBRICATION & MAINTENANCE/HOISTING
- STANDARD PROCEDURE) for the proper lifting
points.
(1) Visually inspect the following for loose attach-
ment, leakage, clearance and routing, and tighten
connections and clamps as required:
²Engine
²Oil Cooler
²Cooling System
²Transmission
²Driveshaft Boots²Differential
²Transfer Case (Fig. 19)
²Transmission Cooler and Lines (Fig. 18)
²Brake System and Lines (Fig. 14)
²Fuel System
²Exhaust System (Fig. 15), (Fig. 16) and (Fig. 17)
²Steering and Suspension Components
Fig. 13 SPARE TIRE INSPECTION
Fig. 14 BRAKE LINES TO CALIPERS (REAR)
Fig. 15 EXHAUST CLAMPS
30 - 8 NEW VEHICLE PREPARATIONBR/BE

²After the vehicle is clean, inspect the paint
again
(2) Mopartoffers a wide variety of car care prod-
ucts, developed to meet your dealership's require-
ments. All are specifically formulated for
DaimlerChrysler vehicles
FINAL STEPS
STANDARD PROCEDURE - OWNER CHECK
OUT
The last step in the new vehicle preparation proce-
dure is to help the customer become familiar with
the features on their new vehicle. Show the new
owner where the controls and gauges are and explain
how they operate.
STANDARD PROCEDURE - INSPECTION -
INFORMATION LABELS
Verify that the following labels are installed and
legible.
²Emission control labels
²Monroney label
²Tire pressure label
²Vehicle certification label
NEW VEHICLE PREPARATION FORM
Complete the Emission Certification Of Conformity
Statement on the bottom of the New Vehicle Prepa-
ration Form (Fig. 1) in the glove box or storage box
after it has been completed and signed by the desig-
nated individual.
30 - 22 NEW VEHICLE PREPARATIONBR/BE
APPEARANCE TIPS (Continued)

INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page

MOUNTED - INSTALLATION, SIDE VIEW
MIRROR - LOW......................23-98
MOUNTED - REMOVAL, SIDE VIEW
MIRROR - LOW......................23-98
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-6
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH...............8L-6
MOUNTING - STANDARD PROCEDURES,
MATCH .............................22-2
MUFFLER - 3.9L/5.2L/5.9L/8.0L -
INSTALLATION.......................11-11
MUFFLER - 3.9L/5.2L/5.9L/8.0L -
REMOVAL..........................11-10
MUFFLER - 5.9L DIESEL - INSTALLATION . 11-11
MUFFLER - 5.9L DIESEL - REMOVAL.....11-11
MULTI-FUNCTION SWITCH -
DESCRIPTION.......................8L-23
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-25
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-28
MULTI-FUNCTION SWITCH - OPERATION . . 8L-24
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-27
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-89
NAME PLATES - REMOVAL, EXTERIOR....23-89
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER..............7-66
NEGATIVE CABLE INSTALLATION,
GASOLINE..........................8F-24
NEGATIVE CABLE REMOVAL, GASOLINE . . . 8F-23
NEUTRAL SAFETY SWITCH -
INSPECTION........................30-19
NEW VEHICLE PREPARATION -
DESCRIPTION, THE IMPORTANCE OF
CAREFUL............................30-1
NEW VEHICLE PREPARATION FORM,
FINAL STEPS........................30-22
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-10
NIGHT MIRROR - INSTALLATION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-11
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY.....................8N-12
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-3
NOISE - INSPECTION, SQUEAKS,
RATTLES AND WIND..................30-15
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-8
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-12
NOISE SUPPRESSION COMPONENTS -
DIAGNOSIS AND TESTING, RADIO.......8A-12
NON-DEPLOYED AIRBAGS - STANDARD
PROCEDURE, HANDLING...............8O-4
NON-MONITORED CIRCUITS - DIESEL -
OPERATION.........................25-23
NON-MONITORED CIRCUITS - GAS
ENGINES - OPERATION................25-22
NOZZLE - DESCRIPTION, WASHER.......8R-9
NOZZLE - INSTALLATION, WASHER.......8R-9
NOZZLE - OPERATION, WASHER.........8R-9
NOZZLE - REMOVAL, WASHER...........8R-9
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION...................Intro.-10
NV231HD - ASSEMBLY, TRANSFER CASE . 21-834
NV231HD - CLEANING, TRANSFER CASE . 21-831
NV231HD - DESCRIPTION, TRANSFER
CASE.............................21-820
NV231HD - DISASSEMBLY, TRANSFER
CASE.............................21-822
NV231HD - INSPECTION, TRANSFER
CASE.............................21-832
NV231HD - INSTALLATION, TRANSFER
CASE
.............................21-847
NV231HD - OPERATION, TRANSFER
CASE
.............................21-820
NV231HD - REMOVAL, TRANSFER CASE
. 21-822
NV231HD - TRANSFER CASE
..........21-849
NV241HD - ASSEMBLY, TRANSFER CASE
. 21-904NV241HD - CLEANING, TRANSFER CASE . 21-902
NV241HD - DESCRIPTION, TRANSFER
CASE.............................21-890
NV241HD - DISASSEMBLY, TRANSFER
CASE.............................21-894
NV241HD - INSPECTION, TRANSFER
CASE.............................21-902
NV241HD - INSTALLATION, TRANSFER
CASE.............................21-919
NV241HD - OPERATION, TRANSFER
CASE.............................21-892
NV241HD - REMOVAL, TRANSFER CASE . 21-894
NV241HD - TRANSFER CASE..........21-920
NV241LD - ASSEMBLY, TRANSFER CASE . 21-869
NV241LD - CLEANING, TRANSFER CASE . 21-866
NV241LD - DESCRIPTION, TRANSFER
CASE.............................21-855
NV241LD - DISASSEMBLY, TRANSFER
CASE.............................21-858
NV241LD - INSPECTION, TRANSFER
CASE.............................21-867
NV241LD - INSTALLATION, TRANSFER
CASE.............................21-882
NV241LD - OPERATION, TRANSFER
CASE.............................21-855
NV241LD - REMOVAL, TRANSFER CASE . 21-858
NV241LD - TRANSFER CASE...........21-884
NV3500 - ASSEMBLY, MANUAL.........21-17
NV3500 - CLEANING, MANUAL..........21-15
NV3500 - DESCRIPTION, MANUAL........21-1
NV3500 - DISASSEMBLY, MANUAL........21-5
NV3500 - INSPECTION, MANUAL........21-15
NV3500 - INSTALLATION, MANUAL......21-40
NV3500 - MANUAL...................21-41
NV3500 - OPERATION, MANUAL..........21-1
NV3500 - REMOVAL, MANUAL...........21-3
NV4500 - ASSEMBLY, MANUAL.........21-65
NV4500 - CLEANING, MANUAL..........21-64
NV4500 - DESCRIPTION, MANUAL.......21-44
NV4500 - DISASSEMBLY, MANUAL.......21-48
NV4500 - INSTALLATION, MANUAL......21-82
NV4500 - MANUAL...................21-83
NV4500 - OPERATION, MANUAL.........21-46
NV4500 - REMOVAL, MANUAL..........21-47
NV4500 - SPECIFICATIONS.............21-83
NV5600 - ASSEMBLY, MANUAL........21-110
NV5600 - DESCRIPTION, MANUAL.......21-91
NV5600 - DISASSEMBLY, MANUAL.......21-95
NV5600 - INSTALLATION, MANUAL.....21-125
NV5600 - OPERATION, MANUAL.........21-93
NV5600 - REMOVAL, MANUAL..........21-94
NV5600 - SPECIFICATIONS............21-126
NV5600 MANUAL TRANSMISSION,
SPECIAL TOOLS....................21-127
O2 SENSOR - DESCRIPTION............14-46
O2 SENSOR - INSTALLATION...........14-48
O2 SENSOR - OPERATION.............14-46
O2 SENSOR - REMOVAL...............14-47
ODOMETER - DESCRIPTION............8J-24
ODOMETER - OPERATION..............8J-25
OFF INDICATOR - DESCRIPTION,
OVERDRIVE.........................8J-27
OFF INDICATOR - OPERATION,
OVERDRIVE.........................8J-27
OFF SWITCH - DESCRIPTION,
OVERDRIVE........................21-215
OFF SWITCH - INSTALLATION,
OVERDRIVE........................21-215
OFF SWITCH - OPERATION, OVERDRIVE . 21-215
OFF SWITCH - REMOVAL, OVERDRIVE . . . 21-215
OIL - DESCRIPTION, ENGINE..........0-3,0-4
OIL - DESCRIPTION, REFRIGERANT......24-56
OIL - OPERATION, REFRIGERANT........24-56
OIL - STANDARD PROCEDURE, ENGINE . . 9-104,
9-160,9-217,9-47
OIL - STANDARD PROCEDURE-ENGINE
OIL LEVEL..........................9-295
OIL - STANDARD PROCEDURE-ENGINE
OIL SERVICE........................9-295
OIL COOLER - INSTALLATION, AIR TO
.....7-88
OIL COOLER & LINES - CLEANING AND
INSPECTION
........................9-296
OIL COOLER - REMOVAL, AIR TO
.........7-87
OIL COOLER - REMOVAL, WATER TO
......7-87
OIL COOLER - STANDARD PROCEDURE,
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION
..............7-80,7-83,7-86OIL COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION..............7-79,7-83,7-85
OIL FILTER - INSTALLATION . 9-105,9-161,9-218,
9-296,9-48
OIL FILTER - REMOVAL.....9-105,9-161,9-218,
9-296,9-48
OIL LEAKS - DIAGNOSIS AND TESTING,
ENGINE..............9-104,9-160,9-215,9-47
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-57
OIL LEVEL, OIL - STANDARD
PROCEDURE-ENGINE.................9-295
OIL PAN - CLEANING . . 9-106,9-162,9-218,9-297,
9-49
OIL PAN - INSPECTION.....9-106,9-162,9-219,
9-297,9-49
OIL PAN - INSTALLATION . . . 9-106,9-162,9-219,
9-297,9-49
OIL PAN - REMOVAL . . 9-105,9-161,9-218,9-296,
9-48
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE . 9-104,9-160,9-215,9-295,9-47
OIL PRESSURE GAUGE - DESCRIPTION . . . 8J-25
OIL PRESSURE GAUGE - OPERATION.....8J-26
OIL PRESSURE RELIEF VALVE -
CLEANING..........................9-297
OIL PRESSURE RELIEF VALVE -
INSPECTION........................9-297
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-298
OIL PRESSURE RELIEF VALVE -
REMOVAL............................9-297
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION...................9-298,9-49
OIL PRESSURE SENSOR/SWITCH -
INSTALLATION.......................9-299
OIL PRESSURE SENSOR/SWITCH -
OPERATION.....................9-298,9-49
OIL PRESSURE SENSOR/SWITCH -
REMOVAL..........................9-298
OIL PUMP - ASSEMBLE..........9-109,9-165
OIL PUMP - ASSEMBLY................9-51
OIL PUMP - ASSEMBLY . . 21-212,21-382,21-558,
21-729
OIL PUMP - CLEANING.......9-220,9-299,9-50
OIL PUMP - CLEANING . . 21-211,21-381,21-557,
21-728
OIL PUMP - DESCRIPTION......21-208,21-379,
21-554,21-724
OIL PUMP - DISASSEMBLE . . . 9-107,9-163,9-50
OIL PUMP - DISASSEMBLY.....21-209,21-380,
21-555,21-726
OIL PUMP - INSPECTION....9-107,9-163,9-220,
9-299,9-50
OIL PUMP - INSPECTION . 21-211,21-382,21-557,
21-728
OIL PUMP - INSTALLATION . . 9-109,9-165,9-221,
9-300,9-52
OIL PUMP - OPERATION . 21-208,21-379,21-554,
21-724
OIL PUMP - REMOVAL......9-107,9-162,9-219,
9-299,9-50
OIL PUMP VOLUME CHECK - STANDARD
PROCEDURE.....21-209,21-379,21-554,21-724
OIL SEAL - FRONT - DESCRIPTION,
CRANKSHAFT...............9-147,9-34,9-91
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT..........9-148,9-277,9-34,9-91
OIL SEAL - FRONT - OPERATION,
CRANKSHAFT...............9-147,9-34,9-91
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT..........9-147,9-276,9-34,9-91
OIL SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT................9-205
OIL SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT....................9-204
OIL SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT
................9-205
OIL SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT
....................9-204
OIL SEAL - REAR - DESCRIPTION,
CRANKSHAFT
...............9-148,9-34,9-91
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
.....9-149,9-206,9-278,9-35,9-92
OIL SEAL - REAR - OPERATION,
CRANKSHAFT
...............9-148,9-34,9-92
BR/BEINDEX 23
Description Group-Page Description Group-Page Description Group-Page

PARK/TURN SIGNAL LAMP -
INSTALLATION.......................8L-29
PARK/TURN SIGNAL LAMP - REMOVAL . . . 8L-29
PARK/TURN SIGNAL LAMP UNIT -
INSTALLATION.......................8L-29
PARK/TURN SIGNAL LAMP UNIT -
REMOVAL..........................8L-29
PARTS - STANDARD PROCEDURES,
CLEANING FUEL SYSTEM..............14-57
PASSENGER AIRBAG - DESCRIPTION....8O-21
PASSENGER AIRBAG - INSTALLATION....8O-23
PASSENGER AIRBAG - OPERATION......8O-21
PASSENGER AIRBAG - REMOVAL........8O-21
PASSENGER AIRBAG ON/OFF SWITCH -
DESCRIPTION.......................8O-23
PASSENGER AIRBAG ON/OFF SWITCH -
INSTALLATION......................8O-25
PASSENGER AIRBAG ON/OFF SWITCH -
OPERATION.........................8O-24
PASSENGER AIRBAG ON/OFF SWITCH -
REMOVAL..........................8O-24
PASSENGER POWER SEAT SWITCH -
DESCRIPTION.......................8N-19
PASSENGER POWER SEAT SWITCH -
DIAGNOSIS & TESTING...............8N-19
PASSENGER POWER SEAT SWITCH -
INSTALLATION......................8N-20
PASSENGER POWER SEAT SWITCH -
OPERATION.........................8N-19
PASSENGER POWER SEAT SWITCH -
REMOVAL..........................8N-20
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION.......................8G-13
PASSENGER SEAT HEATER SWITCH -
INSTALLATION......................8G-16
PASSENGER SEAT HEATER SWITCH -
OPERATION.........................8G-14
PASSENGER SEAT HEATER SWITCH -
REMOVAL..........................8G-15
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-7
PCM - DESCRIPTION..................8E-14
PCM - GAS ENGINES - OPERATION......8E-17
PCM INPUT - OPERATION, ASD SENSE.....8I-3
PCM OUTPUT - DESCRIPTION............8I-3
PCM OUTPUT - OPERATION............14-53
PCM OUTPUT - OPERATION.............8I-3
PCV FILTER - DESCRIPTION............25-35
PCV VALVE - V-6/V-8 ENGINES -
DIAGNOSIS AND TESTING.............25-36
PEDAL - DESCRIPTION.................5-16
PEDAL - INSTALLATION............5-17,5-36
PEDAL - INSTALLATION, ACCELERATOR . . . 14-37
PEDAL - INSTALLATION, CLUTCH.........6-19
PEDAL - OPERATION...................5-16
PEDAL - REMOVAL................5-16,5-36
PEDAL - REMOVAL, ACCELERATOR......14-37
PEDAL - REMOVAL, CLUTCH............6-18
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR..........14-91
PEDAL POSITION SENSOR -
INSTALLATION, ACCELERATOR..........14-93
PEDAL POSITION SENSOR - OPERATION,
ACCELERATOR.......................14-91
PEDAL POSITION SENSOR - REMOVAL,
ACCELERATOR.......................14-91
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-22
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-22
PER MILE, SPECIFICATIONS - TIRE
REVOLUTIONS........................22-9
PERFORMANCE - DIAGNOSIS AND
TESTING...............9-118,9-173,9-4,9-61
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PERFORMANCE - INSPECTION, ENGINE . . . 30-16
PILOT BEARING - DESCRIPTION..........6-17
PILOT BEARING - INSTALLATION.........6-18
PILOT BEARING - OPERATION
...........6-18
PILOT BEARING - REMOVAL
.............6-18
PINION GEAR/RING GEAR -
INSTALLATION
....................3-42,3-74
PINION GEAR/RING GEAR - REMOVAL
. 3-40,3-72
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION
........3-105,3-137,3-166,3-195PINION GEAR/RING GEAR/TONE RING -
REMOVAL...........3-103,3-135,3-165,3-193
PINION SEAL - INSTALLATION.....3-125,3-157,
3-185,3-34,3-66,3-95
PINION SEAL - REMOVAL . . . 3-125,3-156,3-185,
3-34,3-66,3-95
PIPE - 3.9L/5.2L/5.9L - INSPECTION,
EXHAUST............................11-7
PIPE - 3.9L/5.2L/5.9L - INSTALLATION,
EXHAUST............................11-7
PIPE - 3.9L/5.2L/5.9L - REMOVAL,
EXHAUST............................11-7
PIPE - 5.9L DIESEL - INSPECTION,
EXHAUST............................11-9
PIPE - 5.9L DIESEL - INSTALLATION,
EXHAUST...........................11-10
PIPE - 5.9L DIESEL - REMOVAL,
EXHAUST............................11-9
PIPE - 5.9L HEAVY DUTY/8.0L -
INSPECTION, EXHAUST.................11-9
PIPE - 5.9L HEAVY DUTY/8.0L -
INSTALLATION, EXHAUST...............11-9
PIPE - 5.9L HEAVY DUTY/8.0L -
REMOVAL, EXHAUST...................11-8
PISTON & CONNECTING ROD -
CLEANING........9-154,9-209,9-285,9-41,9-98
PISTON & CONNECTING ROD -
CONNECTING RODS..................9-286
PISTON & CONNECTING ROD -
DESCRIPTION.....9-153,9-208,9-282,9-40,9-97
PISTON & CONNECTING ROD -
INSPECTION......9-154,9-209,9-285,9-41,9-98
PISTON & CONNECTING ROD -
INSTALLATION......9-154,9-210,9-287,9-41,9-98
PISTON & CONNECTING ROD -
REMOVAL........9-154,9-209,9-285,9-40,9-97
PISTON FITTING - STANDARD
PROCEDURE...........9-153,9-208,9-40,9-97
PISTON GRADING - STANDARD
PROCEDURE........................9-282
PISTON RETAINER - ASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE
......21-236,21-406,21-581,21-752
PISTON RETAINER - CLEANING,
OVERRUNNING CLUTCH CAM/
OVERDRIVE
......21-236,21-406,21-580,21-752
PISTON RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE
......21-235,21-405,21-580,21-751
PISTON RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE
......21-235,21-405,21-580,21-751
PISTON RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE
......21-236,21-406,21-580,21-752
PISTON RETAINER - OPERATION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE
......21-235,21-405,21-580,21-751
PISTON RING FITTING - STANDARD
PROCEDURE
................9-154,9-41,9-98
PISTON RINGS - STANDARD
PROCEDURE, FITTING
.................9-211
PISTON RINGS - STANDARD
PROCEDURE-PISTON RING FITTING
......9-288
PISTONS - DESCRIPTION
. 21-238,21-408,21-584,
21-755
PISTONS - OPERATION
. . 21-238,21-409,21-584,
21-755
PITMAN BEARING - INSTALLATION
......19-21
PITMAN BEARING - REMOVAL
..........19-20
PITMAN SHAFT - INSTALLATION
........19-23
PITMAN SHAFT - REMOVAL
............19-22
PITMAN SHAFT SEAL - INSTALLATION
....19-24
PITMAN SHAFT SEAL - REMOVAL
.......19-23
PLANETARY GEARTRAIN/OUTPUT
SHAFT - ASSEMBLY
.....21-241,21-412,21-588,
21-760
PLANETARY GEARTRAIN/OUTPUT
SHAFT - DESCRIPTION
. . . 21-240,21-410,21-585,
21-757
PLANETARY GEARTRAIN/OUTPUT
SHAFT - DISASSEMBLY
. . 21-240,21-411,21-586,
21-757
PLANETARY GEARTRAIN/OUTPUT
SHAFT - INSPECTION
....21-241,21-411,21-587,
21-760PLANETARY GEARTRAIN/OUTPUT
SHAFT - OPERATION....21-240,21-410,21-585,
21-757
PLATE - DESCRIPTION, BODY CODE....Intro.-1
PLATE - DESCRIPTION, ENGINE DATA....9-244
PLATE - DESCRIPTION, EQUIPMENT
IDENTIFICATION...................Intro.-12
PLATE - DESCRIPTION, PRESSURE.......6-15
PLATE - INSTALLATION, SUPPORT........5-32
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-11
PLATE - OPERATION, PRESSURE.........6-16
PLATE - REMOVAL, SUPPORT...........5-32
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-11
PLATE LAMP - INSTALLATION, LICENSE . . 8L-22
PLATE LAMP - REMOVAL, LICENSE......8L-22
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-22
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-22
PLATE, SPECIFICATIONS - FUEL
INJECTION PUMP DATA...............14-73
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-89
PLATES - REMOVAL, EXTERIOR NAME....23-89
PLUG - CLEANING, SPARK.............8I-19
PLUG - DESCRIPTION, SPARK...........8I-16
PLUG - INSTALLATION, SPARK..........8I-19
PLUG - INSTALLATION, STEERING GEAR
HOUSING............................19-27
PLUG - OPERATION, SPARK............8I-16
PLUG - REMOVAL, SPARK..............8I-18
PLUG - REMOVAL, STEERING GEAR
HOUSING...........................19-27
PLUG CABLE - DESCRIPTION, SPARK.....8I-19
PLUG CABLE - INSTALLATION, SPARK....8I-20
PLUG CABLE - OPERATION, SPARK.......8I-19
PLUG CABLE - REMOVAL, SPARK........8I-20
PLUG CABLE ORDER, 8.0L V-10 ENGINE
- SPARK .............................8I-2
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK...............8I-3
PLUG CABLES - DIAGNOSIS AND
TESTING, SPARK.....................8I-19
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-16
PLUGS, SPECIFICATIONS - SPARK........8I-3
PLUMBING - CLEANING, CHARGE AIR
COOLER............................11-18
PLUMBING - DESCRIPTION............24-40
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER........................11-17
PLUMBING - INSPECTION, CHARGE AIR
COOLER............................11-18
PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-18
PLUMBING - OPERATION..............24-41
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-17
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-17
POLISHING - DESCRIPTION, WET
SANDING/BUFFING..................23-130
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-1
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-91
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-51
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL.................14-93
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL.................14-91
POSITION SENSOR - OPERATION,
THROTTLE..........................14-51
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL
.................14-91
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL
.......................6-22
POSITION SWITCH - DIAGNOSIS AND
TESTING, PARK/NEUTRAL
......21-237,21-408,
21-583,21-755
POSITION SWITCH - INSTALLATION,
PARK/NEUTRAL
. . . 21-238,21-408,21-583,21-755
POSITION SWITCH - OPERATION,
CLUTCH PEDAL
.......................6-22
BR/BEINDEX 25
Description Group-Page Description Group-Page Description Group-Page

POSITION SWITCH - REMOVAL,
PARK/NEUTRAL . . . 21-238,21-408,21-583,21-755
POSITIVE CABLE INSTALLATION,
GASOLINE..........................8F-23
POSITIVE CABLE REMOVAL, GASOLINE . . . 8F-23
POTENTIAL - STANDARD PROCEDURE,
TESTING FOR VOLTAGE.............8W-01-6
POWER BRAKE BOOSTER -
INSTALLATION........................5-20
POWER BRAKE BOOSTER - REMOVAL.....5-19
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-7
POWER DISTRIBUTION CENTER -
INSTALLATION....................8W-97-8
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-8
POWER DISTRIBUTION CENTER -
REMOVAL........................8W-97-8
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-17
POWER LOCK & REMOTE KEYLESS
ENTRY SYSTEM - DIAGNOSIS AND
TESTING............................8N-4
POWER LOCK MOTOR - DESCRIPTION....8N-6
POWER LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-7
POWER LOCK MOTOR - OPERATION......8N-6
POWER LOCK SWITCH - DESCRIPTION....8N-8
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-8
POWER LOCK SWITCH - OPERATION......8N-8
POWER LOCK SYSTEM - DESCRIPTION....8N-1
POWER LOCK SYSTEM - DIAGNOSIS
AND TESTING........................8N-4
POWER LOCK SYSTEM - OPERATION.....8N-3
POWER LUMBAR ADJUSTER -
DIAGNOSIS & TESTING...............8N-18
POWER MIRROR SWITCH -
DESCRIPTION.......................8N-12
POWER MIRROR SWITCH -
INSTALLATION......................8N-13
POWER MIRROR SWITCH - OPERATION . . 8N-12
POWER MIRROR SWITCH - REMOVAL . . . 8N-12
POWER MIRRORS - DESCRIPTION......8N-10
POWER MIRRORS - OPERATION........8N-10
POWER OUTLET - DESCRIPTION......8W-97-9
POWER OUTLET - DIAGNOSIS &
TESTING........................8W-97-10
POWER OUTLET - INSTALLATION....8W-97-11
POWER OUTLET - OPERATION
.......8W-97-10
POWER OUTLET - REMOVAL
........8W-97-10
POWER SEAT RECLINER - DIAGNOSIS &
TESTING
...........................8N-21
POWER SEAT SWITCH - DESCRIPTION,
DRIVER
............................8N-16
POWER SEAT SWITCH - DESCRIPTION,
PASSENGER
........................8N-19
POWER SEAT SWITCH - DIAGNOSIS &
TESTING, DRIVER
....................8N-16
POWER SEAT SWITCH - DIAGNOSIS &
TESTING, PASSENGER
................8N-19
POWER SEAT SWITCH - INSTALLATION,
DRIVER
............................8N-17
POWER SEAT SWITCH - INSTALLATION,
PASSENGER
........................8N-20
POWER SEAT SWITCH - OPERATION,
DRIVER
............................8N-16
POWER SEAT SWITCH - OPERATION,
PASSENGER
........................8N-19
POWER SEAT SWITCH - REMOVAL,
DRIVER
............................8N-17
POWER SEAT SWITCH - REMOVAL,
PASSENGER
........................8N-20
POWER SEAT SYSTEM - DESCRIPTION
. . . 8N-15
POWER SEAT SYSTEM - DIAGNOSIS &
TESTING
...........................8N-15
POWER SEAT SYSTEM - OPERATION
.....8N-15
POWER SEAT TRACK - DESCRIPTION
....8N-21
POWER SEAT TRACK - DIAGNOSIS &
TESTING
...........................8N-21
POWER SEAT TRACK - INSTALLATION
....8N-22
POWER SEAT TRACK - OPERATION
......8N-21
POWER SEAT TRACK - REMOVAL
.......8N-22POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING GEAR LEAKAGE -
DIAGNOSIS AND TESTING.............19-14
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-20
POWER STEERING GEAR,
SPECIFICATIONS.....................19-19
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-31
POWER STEERING PUMP, SPECIAL
TOOLS.............................19-36
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-32
POWER WINDOW SWITCH -
DESCRIPTION.......................8N-24
POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING.......................8N-24
POWER WINDOW SWITCH -
INSTALLATION......................8N-26
POWER WINDOW SWITCH - OPERATION . . 8N-24
POWER WINDOW SWITCH - REMOVAL . . . 8N-25
POWER WINDOWS - DESCRIPTION......8N-23
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-23
POWER WINDOWS - OPERATION........8N-23
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR SHORT TO GROUND ON FUSES . . . 8W-01-7
POWERTRAIN CONTROL MODULE -
INSTALLATION.......................8E-20
POWERTRAIN CONTROL MODULE -
REMOVAL..........................8E-19
POWR-LOK - ASSEMBLY, DIFFERENTIAL . . 3-163
POWR-LOK - DISASSEMBLY,
DIFFERENTIAL.......................3-161
POWR-LOKYTEST - DIAGNOSIS AND
TESTING...........................3-161
PRE DELIVERY STORAGE -
DESCRIPTION.......................30-19
PRE DELIVERY STORAGE - STANDARD
PROCEDURE........................30-20
PRE-ALIGNMENT - DIAGNOSIS AND
TESTING.............................2-2
PRECAUTIONS - CAUTION,
REFRIGERANT HOSES/LINES/TUBES......24-42
PRECAUTIONS AND WARNINGS, BODY -
SAFETY.............................23-1
PRECAUTIONS, COLUMN - SERVICE......19-6
PRELIMINARY - DIAGNOSIS AND
TESTING........21-143,21-314,21-486,21-657
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-4
PREPARATION - DESCRIPTION, THE
IMPORTANCE OF CAREFUL NEW
VEHICLE............................30-1
PREPARATION FORM, FINAL STEPS -
NEW VEHICLE.......................30-22
PRESSURE - DESCRIPTION, HOSES......19-37
PRESSURE - DIAGNOSIS AND TESTING,
BOOST.............................14-89
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION . 9-124,9-179,9-67,9-9
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL......9-104,9-160,9-215,9-295,9-47
PRESSURE - DIAGNOSIS AND TESTING,
FUEL TRANSFER PUMP...............14-80
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - GAS ENGINES -
SPECIFICATIONS, FUEL SYSTEM.........14-4
PRESSURE - OPERATION, HOSES........19-37
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-8
PRESSURE CAP - CLEANING, RADIATOR . . . 7-66
PRESSURE CAP - DESCRIPTION,
RADIATOR
...........................7-65
PRESSURE CAP - INSPECTION,
RADIATOR
...........................7-66
PRESSURE CAP - OPERATION,
RADIATOR
...........................7-65
PRESSURE FUEL LINES - DESCRIPTION,
HIGH
..............................14-74
PRESSURE FUEL LINES - OPERATION,
HIGH
..............................14-74PRESSURE GAUGE - DESCRIPTION, OIL . . 8J-25
PRESSURE GAUGE - OPERATION, OIL....8J-26
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-7
PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING, FUEL.........14-2
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION . 9-124,9-179,
9-67,9-9
PRESSURE PLATE - DESCRIPTION........6-15
PRESSURE PLATE - OPERATION..........6-16
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-3
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-297
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-46
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-297
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-298
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-46
PRESSURE RELIEF VALVE - REMOVAL,
OIL................................9-297
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL...............9-298,9-49
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL...................9-299
PRESSURE SENSOR/SWITCH -
OPERATION, OIL.................9-298,9-49
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL........................9-298
PRESSURE SWITCH - DESCRIPTION, A/C
HIGH..............................24-20
PRESSURE SWITCH - DESCRIPTION, A/C
LOW ..............................24-21
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C HIGH...................24-20
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C LOW...................24-21
PRESSURE SWITCH - INSTALLATION,
A/C HIGH...........................24-21
PRESSURE SWITCH - INSTALLATION,
A/C LOW ...........................24-22
PRESSURE SWITCH - OPERATION, A/C
HIGH..............................24-20
PRESSURE SWITCH - OPERATION, A/C
LOW ..............................24-21
PRESSURE SWITCH - REMOVAL, A/C
HIGH..............................24-21
PRESSURE SWITCH - REMOVAL, A/C
LOW ..............................24-21
PRESSURE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-10
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC . . . 21-144,21-315,21-487,
21-658
PRESSURES - INSPECTION, TIRE.........30-8
PRESSURES, DIESEL ENGINES - FUEL
SYSTEM
............................14-58
PROCEDURE-CONNECTING ROD
BEARING FITTING, CONNECTING ROD
BEARINGS - STANDARD
................9-31
PROCEDURE-CYLINDER BLOCK
REFACING, ENGINE BLOCK -
STANDARD
.........................9-263
PROCEDURE-CYLINDER BORE,
DE-GLAZE - STANDARD
...............9-264
PROCEDURE-ENGINE OIL LEVEL, OIL -
STANDARD
.........................9-295
PROCEDURE-ENGINE OIL SERVICE, OIL -
STANDARD
.........................9-295
PROCEDURE-PISTON RING FITTING,
PISTON RINGS - STANDARD
...........9-288
PROCEDURE-VALVES,GUIDES AND
SPRINGS, INTAKE/EXHAUST VALVES &
SEATS - STANDARD
..................9-253
PROGRAMMABLE ELECTRONIC
FEATURES - DESCRIPTION
.............30-20
PROGRAMMABLE ELECTRONIC
FEATURES - OPERATION
...............30-20
PROGRAMMING - STANDARD
PROCEDURE, RKE TRANSMITTER
........8N-8
PROPELLER SHAFT - DESCRIPTION
........3-1
PROPELLER SHAFT - DIAGNOSIS AND
TESTING
.............................3-3
26 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

RELAY - OPERATION, A/C COMPRESSOR
CLUTCH............................24-17
RELAY - OPERATION, BLOWER MOTOR . . . 24-22
RELAY - OPERATION, ENGINE STARTER
MOTOR............................8F-42
RELAY - OPERATION, FUEL HEATER......14-63
RELAY - OPERATION, FUEL INJECTION
PUMP.............................14-99
RELAY - OPERATION, FUEL PUMP.......14-41
RELAY - OPERATION, HEADLAMP........8L-17
RELAY - OPERATION, HEATED SEAT.....8G-12
RELAY - OPERATION, HORN.............8H-3
RELAY - OPERATION, INTAKE AIR
HEATER ...........................14-102
RELAY - OPERATION, RADIO CHOKE......8A-8
RELAY - OPERATION, WIPER...........8R-15
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-18
RELAY - REMOVAL, AUTOMATIC SHUT
DOWN..............................8I-4
RELAY - REMOVAL, BLOWER MOTOR....24-23
RELAY - REMOVAL, ENGINE STARTER
MOTOR............................8F-43
RELAY - REMOVAL, FUEL HEATER.......14-65
RELAY - REMOVAL, FUEL PUMP........14-41
RELAY - REMOVAL, HEADLAMP.........8L-18
RELAY - REMOVAL, HEATED SEAT.......8G-13
RELAY - REMOVAL, INTAKE AIR HEATER . 14-102
RELAY - REMOVAL, RADIO CHOKE.........8A-9
RELAY - REMOVAL, WIPER............8R-17
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-3
RELEASE - INSTALLATION..............5-41
RELEASE - REMOVAL..................5-40
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-3
RELEASE BEARING - DESCRIPTION,
CLUTCH.............................6-14
RELEASE BEARING - INSTALLATION,
CLUTCH.............................6-15
RELEASE BEARING - OPERATION,
CLUTCH.............................6-14
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-15
RELEASE CABLE - INSTALLATION........23-83
RELEASE CABLE - INSTALLATION, LATCH . 23-101
RELEASE CABLE - REMOVAL...........23-82
RELEASE CABLE - REMOVAL, LATCH....23-101
RELIEF VALVE - CLEANING, OIL
PRESSURE.........................9-297
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - INSPECTION, OIL
PRESSURE.........................9-297
RELIEF VALVE - INSTALLATION, OIL
PRESSURE.........................9-298
RELIEF VALVE - OPERATION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-297
REMINDER - INSPECTION, TRIP
COMPUTER/MAINTENANCE.............30-17
REMINDER INDICATOR - DESCRIPTION,
SERVICE...........................8J-28
REMINDER INDICATOR - OPERATION,
SERVICE...........................8J-28
REMOTE KEYLESS ENTRY SYSTEM -
DESCRIPTION........................8N-2
REMOTE KEYLESS ENTRY SYSTEM -
DIAGNOSIS AND TESTING, POWER
LOCK...............................8N-4
REMOTE KEYLESS ENTRY SYSTEM -
OPERATION..........................8N-3
REMOTE KEYLESS ENTRY
TRANSMITTER - DESCRIPTION..........8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - OPERATION............8N-7
REMOTE SWITCHES - DESCRIPTION.....8A-15
REMOTE SWITCHES - DIAGNOSIS AND
TESTING
...........................8A-16
REMOTE SWITCHES - OPERATION
.......8A-15
REMOVAL/INSTALLATION, FUEL FILLER
CAP
...............................25-33
REMOVAL/INSTALLATION, FUEL HEATER
. . 14-63
REPAIR - DESCRIPTION, THREADED
HOLE
.............................Intro.-6REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD....21-159,21-330,21-502,
21-673
REPAIR - STANDARD PROCEDURE, CAM
BORE..............................9-267
REPAIR - STANDARD PROCEDURE,
CYLINDER BORE.....................9-265
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE....9-11,9-125,9-181,
9-238,9-68
REPAIRING LEAKS - STANDARD
PROCEDURES........................22-8
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-2
REQUIREMENTS - GAS ENGINES -
DESCRIPTION, FUEL....................0-1
RESERVOIR - DESCRIPTION, VACUUM....24-29
RESERVOIR - DESCRIPTION, VACUUM . . . 8P-13
RESERVOIR - DESCRIPTION, WASHER . . . 8R-10
RESERVOIR - INSTALLATION, FLUID......5-15
RESERVOIR - INSTALLATION, VACUUM . . . 24-30
RESERVOIR - INSTALLATION, VACUUM . . . 8P-14
RESERVOIR - INSTALLATION, WASHER . . . 8R-11
RESERVOIR - OPERATION, VACUUM.....24-29
RESERVOIR - OPERATION, WASHER.....8R-10
RESERVOIR - REMOVAL, FLUID..........5-15
RESERVOIR - REMOVAL, VACUUM.......24-30
RESERVOIR - REMOVAL, VACUUM.......8P-13
RESERVOIR - REMOVAL, WASHER......8R-10
RESISTANCE, 3.9L/5.2L/5.9L ENGINES -
IGNITION COIL........................8I-3
RESISTANCE, 8.0L V-10 ENGINE -
IGNITION COIL........................8I-3
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-3
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-23
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR
............24-24
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR
....................24-24
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR
....................24-23
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR
............................24-24
RESONATOR - INSTALLATION
...........11-13
RESONATOR - REMOVAL
..............11-13
RESTRAINTS - DESCRIPTION
............8O-1
RESTRAINTS - INSPECTION, SEAT
BELTS, SHOULDER BELTS,
RETRACTORS AND HEAD
..............30-12
RESTRAINTS - OPERATION
.............8O-2
RESTRAINTS - WARNING
...............8O-3
RESTRICTIONS - DIAGNOSIS AND
TESTING, FUEL SUPPLY
...............14-56
RETAINER - ASSEMBLY, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-236,
21-406,21-581,21-752
RETAINER - CLEANING, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-236,
21-406,21-580,21-752
RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-235,21-405,21-580,
21-751
RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-235,21-405,21-580,
21-751
RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-236,21-406,21-580,
21-752
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL
.....9-206,9-279
RETAINER - OPERATION, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-235,
21-405,21-580,21-751
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL
.................9-206,9-278
RETRACTOR - INSTALLATION, REAR
SEAT BELT
.........................8O-26
RETRACTOR - REMOVAL, REAR SEAT
BELT
..............................8O-26RETRACTORS AND HEAD RESTRAINTS -
INSPECTION, SEAT BELTS, SHOULDER
BELTS .............................30-12
RETURN - DESCRIPTION, HOSES........19-37
RETURN - DESCRIPTION, SENSOR.......8E-17
RETURN - OPERATION, HOSES..........19-37
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE................22-9
RIGHT FRONT FENDER - INSTALLATION . . 23-94
RIGHT FRONT FENDER - REMOVAL......23-94
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE.....3-105,3-137,3-166,
3-195
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE..........3-103,3-135,3-165,3-193
RING FITTING - STANDARD
PROCEDURE, PISTON.........9-154,9-41,9-98
RING FITTING, PISTON RINGS -
STANDARD PROCEDURE-PISTON........9-288
RINGS - STANDARD PROCEDURE,
FITTING PISTON.....................9-211
RINGS - STANDARD PROCEDURE-
PISTON RING FITTING, PISTON.........9-288
RISER - INSTALLATION, SEAT..........23-141
RISER - REMOVAL, SEAT.............23-141
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
RKE TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE...............8N-8
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TEST - INSPECTION WINDSHIELD
WIPERS/WASHERS....................30-18
ROAD TEST INSPECTION - DESCRIPTION . 30-15
ROAD TESTING - DIAGNOSIS AND
TESTING........21-143,21-314,21-486,21-657
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION........................9-85
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL...........................9-85
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-262
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-261
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-262
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION.............9-142,9-200,9-263
ROCKER ARM / ADJUSTER ASSY -
REMOVAL................9-142,9-200,9-261
ROD - CLEANING, PISTON &
CONNECTING.....9-154,9-209,9-285,9-41,9-98
ROD - CONNECTING RODS, PISTON &
CONNECTING........................9-286
ROD - DESCRIPTION, PISTON &
CONNECTING.....9-153,9-208,9-282,9-40,9-97
ROD - INSPECTION, PISTON &
CONNECTING.....9-154,9-209,9-285,9-41,9-98
ROD - INSTALLATION, PISTON &
CONNECTING.....9-154,9-210,9-287,9-41,9-98
ROD - REMOVAL, PISTON &
CONNECTING.....9-154,9-209,9-285,9-40,9-97
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING............9-274
ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING . . . 9-144,9-202,9-88
ROD BEARING FITTING, CONNECTING
ROD BEARINGS - STANDARD
PROCEDURE-CONNECTING
..............9-31
ROD BEARINGS - STANDARD
PROCEDURE-CONNECTING ROD
BEARING FITTING, CONNECTING
.........9-31
RODS, PISTON & CONNECTING ROD -
CONNECTING
........................9-286
ROLLOVER VALVE - DESCRIPTION
.......14-25
ROLLOVER VALVE - INSTALLATION
......14-27
ROLLOVER VALVE - REMOVAL
..........14-26
ROOF JOINT MOLDING - INSTALLATION
. . 23-91
ROOF JOINT MOLDING - REMOVAL
......23-91
ROTATION - STANDARD PROCEDURES,
TIRE
................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISC BRAKE
.........................5-20
ROTOR - DIAGNOSIS AND TESTING,
DISTRIBUTOR
.......................8I-13
RUN CHANNEL - INSTALLATION, GLASS
. . 23-70
RUN CHANNEL - REMOVAL, GLASS
......23-70
BR/BEINDEX 29
Description Group-Page Description Group-Page Description Group-Page